| Commit message (Collapse) | Author | Age | Files | Lines |
|---|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Now everything is done to load a raw U-Boot proper image instead of
an mkimage-processed one (as far as I tested on NAND, eMMC, NOR).
The SPL already knows the load address of the U-Boot proper without
parsing its uImage header because the load address is defined by
CONFIG_SYS_TEXT_BASE, assuming that the two images are generated from
the same build.
My main motivation of this switch is to use u-boot-with-spl.bin, a
concatenation of u-boot-spl.bin and u-boot.bin. (I wish there were
a concatenation of u-boot-spl.bin and u-boot.img...) Anyway, this
commit would be useful for one-shot image burn.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
| |
|
|
|
|
|
|
|
|
| |
Commit 3cb9abc9c512 ("ARM: uniphier: update U-Boot file names in
workflow") missed to update these two sentences. Fix them now.
Replace u-boot-spl-dtb.bin and u-boot-dtb.img with u-boot-spl.bin
and u-boot.img, respectively.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
| |
|
|
| |
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
| |
|
|
|
|
|
|
| |
PH1-Pro5 support and ProXstream2/PH1-LD6b support can coexist in one
image and there is bit more room in SPL to accommodate all of them.
Merge uniphier_pro5_defconfig into uniphier_pxs2_defconfig.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
| |
|
|
|
|
|
|
|
|
|
|
| |
The Boot ROM expects the boot image (SPL) in the Boot Partition 1.
So, updating images involves the hardware partition switch. It might
be a bit advanced for some users.
To be user-friendly, this commit adds a useful command to update the
images; just put SPL and U-Boot proper into the public directory of
the TFTP server and execute "run emmcupdate" from the command line.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
| |
|
|
|
|
|
| |
Add a driver for the on-chip SD/eMMC host controller used by
UniPhier SoC family.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
| |
|
|
|
|
|
| |
This GPIO controller device is used on UniPhier SoCs.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
| |
Since commit ad1ecd2063da ("fdt: Build a U-Boot binary without device
tree") and commit 03c25bcd263a ("fdt: Build an SPL binary without
device tree"), we can use shorter file names for the output images.
The default configuration for UniPhier SoCs enables CONFIG_OF_SEPARATE
and CONFIG_SPL_OF_CONTROL. In this case, spl/u-boot-spl.bin is the
same as spl/u-boot-spl-dtb.bin. Likewise, u-boot.img is the same as
as u-boot-dtb.img. So, this change of the flow has no impact.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
| |
|
|
|
|
|
|
|
|
|
|
| |
The mem_is_flash() in arch/arm/mach-uniphier/micro-support_card.c
writes/reads the tail of each NOR flash bank to check if the device
really resides there.
If CS1_SPLIT were enabled, the support card would always require two
NOR flash devices to be inserted for the correct NOR detection.
This is not probably what we want.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
| |
|
|
|
|
|
| |
Rename rest of defconfig files of UniPhier SoC family to have the
prefix uniphier_.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
| |
|
|
|
|
|
|
| |
These boards are similar enough to be supported in a single defconfig
file. Distinguish one from another by "DEVICE_TREE" from the command
line. The how-to-build in doc/README.uniphier should be also updated.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
| |
|
|
|
|
|
|
|
| |
These two are similar enough to be merged into a single
defconfig file. Distinguish one from another by "DEVICE_TREE"
from the command line. The how-to-build in doc/README.uniphier
should be also updated.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
| |
|
|
| |
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
| |
|
|
|
|
|
| |
The DDR SDRAM initialization code has not been mainlined yet, but
U-Boot proper should work.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
| |
|
|
|
|
|
| |
The DDR SDRAM initialization code has not been mainlined yet, but
U-Boot proper should work.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
| |
Device Tree really improves code maintainability and is now
available for SPL too.
This is the state-of-the-art implementation in U-boot.
The board files (platform data) are no longer needed.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
| |
|
|
| |
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
| |
|
|
|
|
|
| |
The init code for UMC (Unified Memory Controller) and PLL has not
been mainlined yet, but U-boot proper should work.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
| |
|
|
|
|
|
| |
Support xHCI host driver used on Panasonic UniPhier platform.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Marek Vasut <marex@denx.de>
|
|
|
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
|
