summaryrefslogtreecommitdiffstats
path: root/configs/uniphier_pro4_defconfig
Commit message (Collapse)AuthorAgeFilesLines
* ARM: dts: uniphier: sync DT with latest LinuxMasahiro Yamada2016-10-181-1/+1
| | | | Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
* ARM: uniphier: move CONFIG_SPL_* to defconfig or selectMasahiro Yamada2016-09-231-0/+3
| | | | | | | | | | | | As I repeated in the ML, I am unhappy with config entries with bare defaults. Kick them out of arch/arm/mach-uniphier/Kconfig. Currently, CONFIG_SPL_SERIAL_SUPPORT is not user-configurable (build fails without it), but it should be fixed later anyway, so I am moving CONFIG_SPL_SERIAL_SUPPORT to defconfigs. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* Revert "Increase default of CONFIG_SYS_MALLOC_F_LEN for SPL_OF_CONTROL"Masahiro Yamada2016-09-191-0/+1
| | | | | | | | | | | | | | This reverts commit 90c08d9e08c7a108ab904f3bbdeb558081757892. I took a closer look at this after the commit was applied, and found CONFIG_SYS_MALLOC_F_LEN=0x2000 was too much. 8KB memory for SPL is actually too big for some boards. Perhaps 0x800 is enough, but the situation varies board by board. Let's postpone our decision until we come up with a better idea. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Reviewed-by: Simon Glass <sjg@chromium.org>
* Merge branch 'master' of git://git.denx.de/u-boot-uniphierTom Rini2016-09-181-2/+2
|\
| * ARM: uniphier: select PINCTRL and SPL_PINCTRLMasahiro Yamada2016-09-181-2/+0
| | | | | | | | | | | | | | Now all UniPhier SoCs support a pinctrl driver. Select (SPL_)PINCTRL since it is mandatory even for base use. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
| * ARM: uniphier: enable Generic EHCI driver for Pro4 SoCMasahiro Yamada2016-09-141-0/+2
| | | | | | | | | | | | | | This SoC is equipped with two EHCI cores and two xHCI cores. Enable the generic EHCI driver for the former. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
* | Convert CONFIG_SPL_NOR_SUPPORT to KconfigSimon Glass2016-09-161-0/+1
|/ | | | | | Move this option to Kconfig and tidy up existing uses. Signed-off-by: Simon Glass <sjg@chromium.org>
* Increase default of CONFIG_SYS_MALLOC_F_LEN for SPL_OF_CONTROLMasahiro Yamada2016-09-071-1/+0
| | | | | | | | | | | If both SPL_DM and SPL_OF_CONTROL are enabled, SPL needs to bind several devices, but CONFIG_SYS_MALLOC_F_LEN=0x400 is apparently not enough. Increase the default to 0x2000 for the case. This will be helpful for shorter defconfigs. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Reviewed-by: Stefan Roese <sr@denx.de> Reviewed-by: Simon Glass <sjg@chromium.org>
* ARM: uniphier: enable CONFIG_CMD_CACHEMasahiro Yamada2016-08-281-0/+1
| | | | | | | This will be useful, for example, to load firmware to DRAM and make it visible to other agents. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
* ARM: uniphier: change UNIPHIER_SERIAL to default y optionMasahiro Yamada2016-08-281-1/+0
| | | | | | | This is very likely to be necessary for normal use cases. Set its default to 'y' for shorter defconfig files. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
* ARM: uniphier: move CONFIG_I2C_EEPROM to defconfigMasahiro Yamada2016-07-261-0/+2
| | | | | | | We already have the entry for this option in Kconfig, so let's migrate to it. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
* ARM: uniphier: use the default CONFIG_BOOTDELAY=2Masahiro Yamada2016-06-201-1/+0
| | | | | | | I do not insist on CONFIG_BOOTDELAY=3. The default value in Kconfig, CONFIG_BOOTDELAY=2, is just fine for these boards. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
* common: bootdelay: move CONFIG_BOOTDELAY into a Kconfig optionHeiko Schocher2016-06-091-0/+1
| | | | | | | | | | | move CONFIG_BOOTDELAY into a Kconfig option. Used for this purpose the moveconfig.py tool in tools. Signed-off-by: Heiko Schocher <hs@denx.de> Reviewed-by: Tom Rini <trini@konsulko.com> Acked-by: Viresh Kumar <viresh.kumar@linaro.org> Acked-by: Igor Grinberg <grinberg@compulab.co.il>
* configs: Re-sync with cmd/KconfigTom Rini2016-04-251-0/+3
| | | | | | | Update the config.h and defconfig files for the commands that 8e3c036 converted over to Kconfig Signed-off-by: Tom Rini <trini@konsulko.com>
* defconfig: Reorder boards' defconfig filesBin Meng2016-03-221-1/+0
| | | | | | | Some boards' defconfig files are out of order. Clean this up. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
* Correct defconfig orderingSimon Glass2016-03-141-1/+0
| | | | | | | | Various boards have the wrong Kconfig ordering now. To avoid a misleading diff in the next patch, reorder the configuration correctly. Signed-off-by: Simon Glass <sjg@chromium.org>
* ARM: uniphier: enable UniPhier SD/MMC host driverMasahiro Yamada2016-02-291-0/+1
| | | | | | | Enable the driver in all UniPhier defconfig files and add some needed defines to the common files. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
* ARM: uniphier: enable GPIO command and driver for UniPhier SoCsMasahiro Yamada2016-02-291-0/+2
| | | | | | | This allows to use the "gpio" command. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Acked-by: Simon Glass <sjg@chromium.org>
* ARM: uniphier: rename rest of defconfig filesMasahiro Yamada2015-12-231-0/+30
Rename rest of defconfig files of UniPhier SoC family to have the prefix uniphier_. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
generated by cgit (git 2.34.1) at 2024-11-10 13:57:52 +0000