summaryrefslogtreecommitdiffstats
path: root/configs/pine64_plus_defconfig
Commit message (Collapse)AuthorAgeFilesLines
* configs: Resync with savedefconfigTom Rini2019-02-071-1/+1
| | | | | | Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
* sunxi: usb: Switch to Generic host controllersJagan Teki2019-01-181-0/+1
| | | | | | | | | | | | | | Onc of key blocker for using USB Generic host controller drivers in Allwinner are CLK and RESET drivers, now these available for USB usage. So switch sunxi USB use EHCI and OHCI Generic controllers. Enabling USB is wisely a board choise, So Enable USB_OHCI_HCD where it already have USB_EHCI_HCD Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
* sunxi: disable Pine A64 model detection code on other boardsIcenowy Zheng2018-10-291-0/+1
| | | | | | | | | | | | | | | | | | The Pine A64 Plus/non-Plus model detection code is now built on all 64-bit ARM SoCs, even if the code cannot be triggered when H5/H6 is in use. Disable them when the board is Pine A64 by adding a Kconfig option that is only selected on Pine A64. On GCC 7.3.1 this makes the size of the function reduces 184 bytes, and saves a 104 byte strstr() function, then makes SPL on H6 succeed to build. Signed-off-by: Icenowy Zheng <icenowy@aosc.io> Reviewed-by: Andre Przywara <andre.przywara@arm.com> Acked-by: Maxime Ripard <maxime.ripard@bootlin.com> Reviewed-by: Jagan Teki <jagan@openedev.com>
* configs: Resync with savedefconfigTom Rini2018-09-031-1/+1
| | | | | | Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
* configs: Migrate CONFIG_NR_DRAM_BANKSTom Rini2018-08-161-0/+1
| | | | | | | | | | | We have the following cases: - CONFIG_NR_DRAM_BANKS was defined, migrate normally - CONFIG_NR_DRAM_BANKS_MAX was defined and then used for CONFIG_NR_DRAM_BANKS after a check, just migrate it over now. - CONFIG_NR_DRAM_BANKS was very oddly defined on p2771-0000-* (to 1024 + 2), set this to 8. Signed-off-by: Tom Rini <trini@konsulko.com>
* part: Disable CONFIG_SPL_ISO_PARTITION by defaultAlexander Graf2018-04-161-1/+0
| | | | | | | | | | | | | | | | We enabled CONFIG_ISO_PARTITION by default for distro boot, so that U-Boot could load distro images that usually get shipped as iso images. These images usually come with a board agnostic boot environment. However, there is very little point in having ISO support enabled (for anyone really) in SPL, as the whole idea of SPL is to load U-Boot proper which again is board specific. So the fact that we enable ISO support in U-Boot proper does not mean at all that we want ISO support in U-Boot SPL. Hence, let's remove the Kconfig dependency. Along the way, let's also clean up all those default configs that disabled SPL ISO support. Signed-off-by: Alexander Graf <agraf@suse.de>
* configs: Resync with savedefconfigTom Rini2018-04-071-3/+3
| | | | | | Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
* Merge git://git.denx.de/u-boot-sunxiTom Rini2018-04-041-0/+1
|\ | | | | | | Signed-off-by: Tom Rini <trini@konsulko.com>
| * Revert "sunxi: Pine64: temporarily remove extra Pine64 non-plus DT"Andre Przywara2018-04-041-0/+1
| | | | | | | | | | | | | | | | | | | | Now with the MMC environment gone, we have enough space to accommodate the Pine64 "non-plus" .dtb again. This reverts commit 47952b8e42c2790150e16d3d4235b3a1ee0ba9bb. Signed-off-by: Andre Przywara <andre.przywara@arm.com> Reviewed-by: Jagan Teki <jagan@openedev.com>
* | Configs: Use the newly added PHY_RTL8211E_PINE64_GIGABIT_FIXkevans@FreeBSD.org2018-03-221-0/+2
|/ | | | | | | | The Pine64+ uses a generic PHY driver, so flip it over to using the Realtek PHY driver to actually apply the RTL8211e fix. Signed-off-by: Kyle Evans <kevans@FreeBSD.org> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
* sunxi: move CONFIG_SYS_TEXT_BASE out of defconfigsAndre Przywara2018-03-141-1/+0
| | | | | | | | | | | | | | | | | Commit 278b90ce786f ("configs: Migrate CONFIG_SYS_TEXT_BASE") made CONFIG_SYS_TEXT_BASE a proper Kconfig variable, with the consequence of moving the common definition shared by almost every sunxi board into 123 individual defconfig files. But the U-Boot start address for Allwinner boards is a platform decision which has been around for ages, so defining it in each *board* config file seems a bit over the top. Define the standard values (160MB into DRAM for most SoCs, with two SoC exceptions) if ARCH_SUNXI is selected, and delete the lines from the individual defconfigs. Signed-off-by: Andre Przywara <andre.przywara@arm.com> Acked-by: Maxime Ripard <maxime.ripard@bootlin.com> Reviewed-by: Jagan Teki <jagan@openedev.com>
* sunxi: Pine64: temporarily remove extra Pine64 non-plus DTAndre Przywara2018-03-131-1/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | With the merge of the new u-boot.itb size check now the build for pine64_plus_defconfig breaks, as this file gets too large: ============= u-boot.itb exceeds file size limit: limit: 516096 bytes actual: 521852 bytes excess: 5756 bytes make: *** [u-boot.itb] Error 1 ============= One easily fixable reason is that we actually have two .dtbs in our FIT image, one for the regular Pine64+ board, and one for the non-plus version. The only difference U-Boot cares about is the 100Mbit Ethernet PHY used on the non-plus version, however Ethernet isn't enabled in the non-plus DT anyway. So we could avoid the non-plus special handling, and remove that extra .dtb from the FIT image, which saves a few KBs and brings us back below the limit. The Pine64 would boot with a Pine64+ .dtb, and would fail to enable Ethernet. Given that it didn't work in the first place, this is not a regression. Once we switch to a non-MMC environment, we can bring this back, then with a proper .dtb and hopefully working Ethernet. Signed-off-by: Andre Przywara <andre.przywara@arm.com> Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
* configs: Migrate CONFIG_SYS_TEXT_BASETom Rini2018-02-111-0/+1
| | | | | | | | | | | On the NIOS2 and Xtensa architectures, we do not have CONFIG_SYS_TEXT_BASE set. This is a strict migration of the current values into the defconfig and removing them from the headers. I did not attempt to add more default values in and for now will leave that to maintainers. Signed-off-by: Tom Rini <trini@konsulko.com>
* cmd: Make CONFIG_CMD_FPGA depend on CONFIG_FPGATuomas Tynkkynen2018-02-051-1/+0
| | | | | | | | | | | | | | | | | | cmd/Makefile has: ifdef CONFIG_FPGA obj-$(CONFIG_CMD_FPGA) += fpga.o endif which means that if CONFIG_FPGA is not set, CONFIG_CMD_FPGA silently does nothing. Let's remove that Makefile conditional and instead express this equivalent dependency in Kconfig, so a lot of redundant # CONFIG_CMD_FPGA is not set can be removed from board defconfigs that don't actually have an FPGA. Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
* cmd: Toggle the default value of CONFIG_CMD_IMLSTuomas Tynkkynen2017-10-101-1/+0
| | | | | | | | | | | | | | Having this as a 'default y' is rather annoying because it doesn't actually compile unless other options are defined in the board header: ../cmd/bootm.c: In function 'do_imls_nor': ../cmd/bootm.c:330:7: error: 'CONFIG_SYS_MAX_FLASH_BANKS' undeclared (first use in this function); did you mean 'CONFIG_SYS_MAX_FLASH_SECT'? i < CONFIG_SYS_MAX_FLASH_BANKS; ++i, ++info) { Make it 'default n' so people who develop new boards that start from a blank defconfig have one less compilation failure to debug. Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
* configs: Migrate all of the existing USB symbols, except fastbootTom Rini2017-09-011-0/+1
| | | | | | | | | | | | This syncs all of the currently Kconfig'd symbols out of the headers and into the defconfig files. This has two exceptions, first am335x_evm needs to be converted to DM in SPL and then it can stop undef'ing CONFIG_DM_USB. Leaving this as-is results in a build failure, and without work, run time failure. The other case is am43xx_evm.h and in turn am43xx_evm_usbhost_boot. The problem here is that we need DWC3 USB host mode in SPL, but still desire to have gadget mode in U-Boot proper. Signed-off-by: Tom Rini <trini@konsulko.com>
* configs: Resync defconfigsTom Rini2017-06-191-2/+1
| | | | Signed-off-by: Tom Rini <trini@konsulko.com>
* sunxi: defconfig: add supported DT list for Pine64Andre Przywara2017-05-171-0/+1
| | | | | | | | | | | | | | When a board uses a FIT image to load U-Boot proper, it requires a list of supported device trees to be supplied in CONFIG_OF_LIST, from which it chooses the right one at runtime. For boards with just one possible DT (like the OrangePi PC2) this defaults to CONFIG_DEFAULT_DEVICE_TREE, but for the Pine64 with its two possible models we provide all compatible DTs in this config symbol. Signed-off-by: Andre Przywara <andre.przywara@arm.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Jagan Teki <jagan@openedev.com> Tested-by: Jagan Teki <jagan@openedev.com>
* configs: Re-syncTom Rini2017-03-131-1/+1
| | | | Signed-off-by: Tom Rini <trini@konsulko.com>
* disk: convert CONFIG_EFI_PARTITION to KconfigPatrick Delaunay2017-01-281-0/+1
| | | | | Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Signed-off-by: Patrick Delaunay <patrick.delaunay73@gmail.com>
* disk: convert CONFIG_ISO_PARTITION to KconfigPatrick Delaunay2017-01-281-0/+1
| | | | | Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Signed-off-by: Patrick Delaunay <patrick.delaunay73@gmail.com>
* disk: convert CONFIG_DOS_PARTITION to KconfigPatrick Delaunay2017-01-281-0/+1
| | | | | Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Signed-off-by: Patrick Delaunay <patrick.delaunay73@gmail.com>
* sunxi: A64: enable SPLAndre Przywara2017-01-041-0/+1
| | | | | | | | | | | | | | | | Now that the SPL is ready to be compiled in AArch64 and the DRAM init code is ready, enable SPL support for the A64 SoC and in the Pine64 defconfig. For now we keep the boot0 header in the U-Boot proper, as this allows to still use boot0 as an SPL replacement without hurting the SPL use case. We disable FEL support for now by making its compilation conditional and disabling it for ARM64, as the code isn't ready yet. Signed-off-by: Andre Przywara <andre.przywara@arm.com> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Jagan Teki <jagan@openedev.com>
* sunxi: provide default DRAM config for sun50i in KconfigAndre Przywara2017-01-041-2/+0
| | | | | | | | | | | | To avoid enumerating the very same DRAM values in defconfig files for each and every Allwinner A64 board out there, let's put some sane default values in the Kconfig file. Boards with different needs can override them at any time. Signed-off-by: Andre Przywara <andre.przywara@arm.com> Reviewed-by: Simon Glass <sjg@chromium.org> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> Reviewed-by: Jagan Teki <jagan@openedev.com>
* sunxi: introduce extra config option for boot0 headerAndre Przywara2017-01-041-1/+1
| | | | | | | | | | | | The ENABLE_ARM_SOC_BOOT0_HOOK option is a generic option shared with other boards. To allow alternative code to be inserted, we create another, now function specific config symbol on top of it to simplify later additions. No functional change at this time. Signed-off-by: Andre Przywara <andre.przywara@arm.com> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Jagan Teki <jagan@openedev.com>
* sunxi: A64: enable USB supportAmit Singh Tomar2016-10-301-0/+1
| | | | | | | | | | | | | | | | Mostly by adding MACH_SUN50I to some existing #ifdefs enable support for the the HCI0 USB host controller on the A64. Fix up some minor 64-bit hiccups on the way. Add the bare minimum DT bits to the A64 .dtsi and enable the controllers and the PHY on the Pine64. This is limited to the first USB controller at the moment, which is connected to the lower USB socket on the Pine64 board. [Andre: remove unneeded defines, enable OHCI, add commit message] Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com> Signed-off-by: Andre Przywara <andre.przywara@arm.com> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
* Convert CONFIG_SYS_CONSOLE_IS_IN_ENV and CONFIG_CONSOLE_MUX to KconfigSimon Glass2016-10-231-0/+1
| | | | | | | | | | This converts the following to Kconfig: CONFIG_SYS_CONSOLE_IS_IN_ENV CONFIG_CONSOLE_MUX Signed-off-by: Simon Glass <sjg@chromium.org> [trini: Re-order, re-migrate] Signed-off-by: Tom Rini <trini@konsulko.com>
* configs: Resync with savedefconfigTom Rini2016-09-091-2/+1
| | | | Signed-off-by: Tom Rini <trini@konsulko.com>
* sunxi: Re-enable h3 emac supportHans de Goede2016-07-311-0/+1
| | | | | | | | | | | | | | With the recent bug fixes for the sun8i_emac driver all known issues are resolved, so we can re-enable the driver. While at it, also enable the emac on the Orange Pi One. Cc: Chen-Yu Tsai <wens@csie.org> Cc: Corentin LABBE <clabbe.montjoie@gmail.com> Cc: Amit Singh Tomar <amittomer25@gmail.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk> Acked-by: Jagan Teki <jteki@openedev.com>
* sunxi: Disable sun8i emac driverHans de Goede2016-07-271-1/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | Disable the sun8i emac driver for now, there are 2 issues with it: 1) It is causing issues with network connectivity under the kernel driver, when booting the kernel with v2 of Corentin's sun8i-h3 emac driver, I get the connection status bouncing between connected at 100mbps full-duplex and being down every second. The second issue is that when trying to use it from u-boot I get a number of unaligned cache flush errors: => dhcp BOOTP broadcast 1 BOOTP broadcast 2 CACHE: Misaligned operation at range [7bf594a8, 7bf59628] BOOTP broadcast 3 CACHE: Misaligned operation at range [7bf59c90, 7bf59e10] CACHE: Misaligned operation at range [7bf5a478, 7bf5a5f8] DHCP client bound to address 10.42.43.80 (1009 ms) Cc: Chen-Yu Tsai <wens@csie.org> Cc: Corentin LABBE <clabbe.montjoie@gmail.com> Cc: Amit Singh Tomar <amittomer25@gmail.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
* net: Add EMAC driver for H3/A83T/A64 SoCs.Amit Singh Tomar2016-07-151-0/+1
| | | | | | | | | | | This patch add EMAC driver support for H3/A83T/A64 SoCs. Tested on Pine64(A64-External PHY) and Orangepipc(H3-Internal PHY). BIG Thanks to Andre for providing some of the DT code. Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
* configs: Re-sync BOOTDELAY changesTom Rini2016-06-171-1/+1
| | | | | | | | With updated moveconfig.py and an better default, re-generate the migration of BOOTDELAY to the defconfig. Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Tom Rini <trini@konsulko.com>
* common: bootdelay: move CONFIG_BOOTDELAY into a Kconfig optionHeiko Schocher2016-06-091-1/+1
| | | | | | | | | | | move CONFIG_BOOTDELAY into a Kconfig option. Used for this purpose the moveconfig.py tool in tools. Signed-off-by: Heiko Schocher <hs@denx.de> Reviewed-by: Tom Rini <trini@konsulko.com> Acked-by: Viresh Kumar <viresh.kumar@linaro.org> Acked-by: Igor Grinberg <grinberg@compulab.co.il>
* arm/arm64: implement a boot header capabilityAndre Przywara2016-06-061-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Some SPL loaders (like Allwinner's boot0, and Broadcom's boot0) require a header before the actual U-Boot binary to both check its validity and to find other data to load. Sometimes this header may only be a few bytes of information, and sometimes this might simply be space that needs to be reserved for a post-processing tool. Introduce a config option to allow assembler preprocessor commands to be inserted into the code at the appropriate location; typical assembler preprocessor commands might be: .space 1000 .word 0x12345678 Signed-off-by: Andre Przywara <andre.przywara@arm.com> Signed-off-by: Steve Rae <srae@broadcom.com> Commit Notes: Please note that the current code: start.S (arm64) and vectors.S (arm) already jumps over some portion of data already, so this option basically just increases the size of this region (and the resulting binary). For use with Allwinner's boot0 blob there is a tool called boot0img[1], which fills the header to allow booting A64 based boards. For the Pine64 we need a 1536 byte header (including the branch instruction) at the moment, so we add this to the defconfig. [1] https://github.com/apritzel/pine64/tree/master/tools END Reviewed-by: Tom Rini <trini@konsulko.com>
* sunxi: Enable a bunch of commands by default on sunxiHans de Goede2016-05-251-9/+0
| | | | | | | | | | | | | Recently a set of CONFIG_CMD_FOO defines was moved from being defined in config_distro_defaults to Kconfig, and added to all sunxi defconfigs to compensate. Instead of explictly selecting these in all sunxi defconfigs, simply always select these for sunxi boards. This makes the defconfigs simpler and ensures a consistent set of available commands across all sunxi boards. Signed-off-by: Hans de Goede <hdegoede@redhat.com>
* arm64: Pine64: update FDT filesAndre Przywara2016-05-251-1/+1
| | | | | | | | | | | | | The originally committed .dts files for the Pine64 were from an early proof-of-concept version and should have never been committed upstream. Replace them with much more mature versions, which also use a different naming scheme. Please note that at this point there is at least one binding which has not been agreed upon, so this is subject to change. Signed-off-by: Andre Przywara <andre.przywara@arm.com> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
* configs: Re-sync with cmd/KconfigTom Rini2016-04-251-0/+6
| | | | | | | Update the config.h and defconfig files for the commands that 8e3c036 converted over to Kconfig Signed-off-by: Tom Rini <trini@konsulko.com>
* configs: Re-sync almost all of cmd/KconfigTom Rini2016-04-251-0/+2
| | | | | | | | This syncs up the current cmd/Kconfig and include/configs/ files with the only exception being CMD_NAND. Due to how we have used this historically we need to take further care here when converting. Signed-off-by: Tom Rini <trini@konsulko.com>
* configs: Re-sync HUSH optionsTom Rini2016-04-251-0/+1
| | | | | | | Move all cases of CONFIG_SYS_HUSH_PARSER out of the config.h files. Remove all cases of CONFIG_SYS_PROMPT_HUSH_PS2 as everyone uses the default. Signed-off-by: Tom Rini <trini@konsulko.com>
* sunxi: Enable CMD_GPIO on all sunxi boardsHans de Goede2016-04-121-1/+0
| | | | | | | | | | | | | We have CONFIG_CMD_GPIO=y in almost all sunxi boards, but after its Kconfig conversion it has ended up missing on some recently added boards. Simply select it for ARCH_SUNXI, so that we get it on all sunxi boards for both a consistent user experience and simpler defconfig files. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* sunxi: Add Pine64+ supportSiarhei Siamashka2016-04-011-0/+12
The Pine64+ is a system based on the Allwinner A64 SoC. It is capable of running AArch64 code and thus is the first of its kind for the sunxi target. This patch adds a defconfig and device tree chunks for it. Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com> [agraf: Change patch description] Signed-off-by: Alexander Graf <agraf@suse.de> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
generated by cgit (git 2.34.1) at 2024-11-19 12:32:35 +0000