summaryrefslogtreecommitdiffstats
path: root/configs/imx8mm_evk_defconfig
Commit message (Collapse)AuthorAgeFilesLines
* imx8mm_evk: switch to use binman to pack imagesPeng Fan2021-04-081-2/+2
| | | | | | Use binman to pack images Signed-off-by: Peng Fan <peng.fan@nxp.com>
* imx8mm_evk: Switch to new imx8mm evk boardYe Li2021-04-081-1/+1
| | | | | | Update PMIC to use PCA9540, the legacy board not supported by NXP Signed-off-by: Ye Li <ye.li@nxp.com>
* configs: Resync with savedefconfigTom Rini2021-01-291-1/+1
| | | | | | Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
* imx8mm: configs: add support for distro boot commandsAlice Guo2021-01-231-0/+2
| | | | | | | | | | | | | | | | | | | | | Supported boot device types in iMX8MM: MMC, DHCP. CONFIG_CMD_PART is added for command part and CONFIG_CMD_FS_GENERIC is for command fstype. CONFIG_BOOTCOMMAND which is defined in include/configs/imx8mm_evk.h is deleted because "run distro_bootcmd" is required to be the default boot mode. scriptaddr is the location in RAM where boot.scr.uimg/boot.scr will be loaded to prior to execution. kernel_addr_r is the location in RAM where the kernel will be loaded to. Delete unnecessary environment variables. Reviewed-by: Peng Fan <peng.fan@nxp.com> Signed-off-by: Alice Guo <alice.guo@nxp.com>
* configs: imx8m: enable eMMC HS400ES and SD UHS mode on EVKAndrey Zhizhikin2020-12-261-0/+4
| | | | | | | | i.MX8M series includes support for high speed modes in uSDHC controllers. Turn on corresponding configuration options for EVK boards, which would enable high speed modes to be included in U-Boot. Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
* Convert CONFIG_SYS_MMC_ENV_DEV et al to KconfigTom Rini2020-08-081-0/+1
| | | | | | | | | | | | This converts the following to Kconfig: CONFIG_SYS_MMC_ENV_DEV CONFIG_SYS_MMC_ENV_PART Note that with this conversion we now have consistent behavior with respect to ensuring that we have always selected the correct MMC device and hardware partition. Signed-off-by: Tom Rini <trini@konsulko.com>
* Convert CONFIG_ENV_OVERWRITE to KconfigAdam Ford2020-07-281-0/+1
| | | | | | | | | This converts the following to Kconfig: CONFIG_ENV_OVERWRITE Signed-off-by: Adam Ford <aford173@gmail.com> [trini: Rerun migration, remove some comments] Signed-off-by: Tom Rini <trini@konsulko.com>
* configs: Resync with savedefconfigTom Rini2020-07-281-1/+1
| | | | | | Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
* configs: Resync with savedefconfigTom Rini2020-07-061-1/+1
| | | | | | Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
* imx8mm_evk: Select the watchdog driverFabio Estevam2020-06-081-1/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | Currently the watchdog driver is not selected, which causes the following warnings in both SPL and U-Boot proper: U-Boot SPL 2020.07-rc1-00387-g67887903af (May 07 2020 - 23:49:27 -0300) Normal Boot WDT: Started without servicing (60s timeout) Trying to boot from MMC1 U-Boot 2020.07-rc1-00387-g67887903af (May 07 2020 - 23:49:27 -0300) CPU: Freescale i.MX8MMQ rev1.0 at 1200 MHz Reset cause: POR Model: FSL i.MX8MM EVK board DRAM: 2 GiB WDT: Started without servicing (60s timeout) .... System reboots after staying 60s in the U-Boot prompt. Fix this problem by enabling CONFIG_WATCHDOG so that watchdog can be properly serviced. Suggested-by: Marek Vasut <marex@denx.de> Signed-off-by: Fabio Estevam <festevam@gmail.com>
* ARM: imx8m: Fix reset in SPL on NXP iMX8MM EVKMarek Vasut2020-05-011-0/+5
| | | | | | | | | | | | | | | | | | | Board files should not re-implement do_reset() to work around this function not being defined in for specific configurations. Rather, the fix is to compile in drivers which implement this properly. This patch enables sysreset and watchdog drivers in SPL and ties them together to implement the same as the do_reset() hack in the board file, except correctly in the DM/DT framework. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Fabio Estevam <festevam@gmail.com> Cc: Flavio Suligoi <f.suligoi@asem.it> Cc: Harald Seiler <hws@denx.de> Cc: Igor Opaniuk <igor.opaniuk@toradex.com> Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com> Cc: Oleksandr Suvorov <oleksandr.suvorov@toradex.com> Cc: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de>
* imx8: Run SPL with caches enabledFabio Estevam2020-05-011-2/+0
| | | | | | | | | | | | It is safe to run SPL with caches enabled on i.MX8, so remove such restriction. Signed-off-by: Fabio Estevam <festevam@gmail.com> Acked-by: Peng Fan <peng.fan@nxp.com> Acked-by: Oliver Graute <oliver.graute@kococonnector.com> Acked-by: Anatolij Gustschin <agust@denx.de> Tested-by: Igor Opaniuk <igor.opaniuk@toradex.com> Acked-by: Igor Opaniuk <igor.opaniuk@toradex.com>
* configs: Resync with savedefconfigTom Rini2020-04-281-2/+2
| | | | | | Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
* configs: Resync with savedefconfigTom Rini2020-01-221-6/+6
| | | | | | Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
* imx8mm_evk: Adjust the environment for booting a mainline kernelFabio Estevam2020-01-071-1/+0
| | | | | | | Adjust the environment for booting a mainline kernel by default. Signed-off-by: Fabio Estevam <festevam@gmail.com> Reviewed-by: Peng Fan <peng.fan@nxp.com>
* env: Finish migration of common ENV optionsTom Rini2019-11-201-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | - In ARMv8 NXP Layerscape platforms we also need to make use of CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so. - On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define to 0. - Add Kconfig entry for ENV_ADDR. - Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it. - Add ENV_xxx_REDUND options that depend on their primary option and SYS_REDUNDAND_ENVIRONMENT - On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR for the pre-main-U-Boot environment location. - On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but rather it being non-zero, as it will now be zero by default. - Rework the env_offset absolute in env/embedded.o to not use CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within ENV_IS_IN_FLASH. - Migrate all platforms. Cc: Wolfgang Denk <wd@denx.de> Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Patrick Delaunay <patrick.delaunay@st.com> Cc: uboot-stm32@st-md-mailman.stormreply.com Signed-off-by: Tom Rini <trini@konsulko.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
* env: Add CONFIG_SYS_RELOC_GD_ENV_ADDR symbolTom Rini2019-11-201-0/+1
| | | | | | | | | | | Today in initr_reloc_global_data() we use some non-obvious tests to determine if we need to relocate the env_addr within gd or not. In order to facilitate migration of other symbols to Kconfig we need to introduce a new symbol for this particular use case. Cc: Wolfgang Denk <wd@denx.de> Cc: Joe Hershberger <joe.hershberger@ni.com> Signed-off-by: Tom Rini <trini@konsulko.com>
* imx: imx8mm-evk: enable ethernetPeng Fan2019-11-051-0/+7
| | | | | | | | add phy-reset-gpios to reset phy Add board_phy_config to configure phy Enable DM_ETH Signed-off-by: Peng Fan <peng.fan@nxp.com>
* imx8mm: evk: enable bd71837 pmicPeng Fan2019-11-031-1/+4
| | | | | | | Enable bd71837 pmic for i.MX8MM EVK board, need to set voltage for DRAM and linux suspend voltage requirement. Signed-off-by: Peng Fan <peng.fan@nxp.com>
* imx: Add i.MX8MM EVK board support.Peng Fan2019-10-081-0/+74
Add board and SoC dts Add ddr training code support SD/MMC/GPIO/PINCTRL/UART Signed-off-by: Peng Fan <peng.fan@nxp.com>
generated by cgit (git 2.34.1) at 2024-09-22 07:52:22 +0000