summaryrefslogtreecommitdiffstats
path: root/board/ti
Commit message (Collapse)AuthorAgeFilesLines
* Merge branch '2019-10-24-ti-imports'Tom Rini2019-10-251-0/+1
|\ | | | | | | | | - Enable DFU on dra7xx boards - Further Keystone 3 platform improvements
| * armv7R: K3: j721e: Add support for triggering ddr init from SPLLokesh Vutla2019-10-251-0/+1
| | | | | | | | | | | | | | | | In SPL, DDR should be made available by the end of board_init_f() so that apis in board_init_r() can use ddr. Adding support for triggering DDR initialization from board_init_f(). Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
* | ARM: keystone: Do not enable the USB power domains at the board levelJean-Jacques Hiblot2019-10-241-13/+0
|/ | | | | | | This breaks linux boot sequence. Observed on k2e and k2l platforms. Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
* board: ti: am335x-ice: Configure the CDCE913 clock synthesizerTero Kristo2019-10-111-0/+4
| | | | | | | | | | AM335x-ICE boards contain the CDCE913 clock synthesizer, and their reset crystal capacitance load value of 10pF is wrong leading into lost packets in certain networking tests. Add DT data for this device, and probe it from the board file to program the crystal capacitance load value to 0pF to avoid any problems. Signed-off-by: Tero Kristo <t-kristo@ti.com>
* board: ti: am43xx-idk: Configure the CDCE913 clock synthesizerTero Kristo2019-10-111-0/+5
| | | | | | | | | | AM43xx-IDK boards contain the CDCE913 clock synthesizer, and their reset crystal capacitance load value of 10pF is wrong leading into lost packets in certain networking tests. Add DT data for this device, and probe it from the board file to program the crystal capacitance load value to 0pF to avoid any problems. Signed-off-by: Tero Kristo <t-kristo@ti.com>
* board: ti: am57xx-idk: Configure the CDCE913 clock synthesizerTero Kristo2019-10-111-0/+5
| | | | | | | | | | AM57xx-IDK boards contain the CDCE913 clock synthesizer, and their reset crystal capacitance load value of 10pF is wrong leading into lost packets in certain networking tests. Add DT data for this device, and probe it from the board file to program the crystal capacitance load value to 0pF to avoid any problems. Signed-off-by: Tero Kristo <t-kristo@ti.com>
* board: am65x: Print board name and version during bootLokesh Vutla2019-10-111-1/+14
| | | | | | | Print the board name and ver along with the DT Model. While at it print the ver for all the detected daughter cards. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
* board: j721e: Add READMELokesh Vutla2019-10-111-0/+227
| | | | | | Add README file explaining the build and boot procedure for J721E evm. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
* board: ti: am65x: Add UART boot procedure in READMEAndreas Dannenberg2019-10-111-0/+32
| | | | | | | | | am65x ROM support booting over UART. And U-Boot built for am65x EVM supports UART boot as well. Add the UART boot procedure into the README also providing a corresponding example command sequence for execution on a host PC. Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
* board: ti: am654: Disable TRNG node for HS devicesAndrew F. Davis2019-10-041-2/+13
| | | | | | | | On HS devices the access to TRNG is restricted on the non-secure ARM side, disable the node in DT to prevent firewall violations. Signed-off-by: Andrew F. Davis <afd@ti.com> Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
* env: Rename environment.h to env_internal.hSimon Glass2019-08-111-1/+1
| | | | | | | | | | | | | | This file contains lots of internal details about the environment. Most code can include env.h instead, calling the functions there as needed. Rename this file and add a comment at the top to indicate its internal nature. Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> [trini: Fixup apalis-tk1.c] Signed-off-by: Tom Rini <trini@konsulko.com>
* env: Drop environment.h header file where not neededSimon Glass2019-08-116-6/+0
| | | | | | | | This header file is now only used by files that access internal environment features. Drop it from various places where it is not needed. Acked-by: Joe Hershberger <joe.hershberger@ni.com> Signed-off-by: Simon Glass <sjg@chromium.org>
* env: Move env_get() to env.hSimon Glass2019-08-111-0/+1
| | | | | | | Move env_get() over to the new header file. Acked-by: Joe Hershberger <joe.hershberger@ni.com> Signed-off-by: Simon Glass <sjg@chromium.org>
* env: Move env_set() to env.hSimon Glass2019-08-118-0/+8
| | | | | | | Move env_set() over to the new header file. Acked-by: Joe Hershberger <joe.hershberger@ni.com> Signed-off-by: Simon Glass <sjg@chromium.org>
* env: Move env_get_ulong() to env.hSimon Glass2019-08-111-0/+1
| | | | | | | Move env_get_ulong() over to the new header file. Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
* env: Move env_init() to env.hSimon Glass2019-08-113-0/+3
| | | | | | | Move env_init() over to the new header file. Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
* configs: j721e_evm_a72: Add initial supportLokesh Vutla2019-07-261-0/+1
| | | | | | | | Add initial defconfig support for J721e that runs on A72. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> [trini: Add MAINTAINERS entry] Signed-off-by: Tom Rini <trini@konsulko.com>
* configs: j721e_evm_r5: Add initial supportLokesh Vutla2019-07-261-0/+6
| | | | | | | | Add initial defconfig support for J721e that runs on R5. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> [trini: Add MAINTAINERS file] Signed-off-by: Tom Rini <trini@konsulko.com>
* board: ti: j721e: Enable fixing up msmc sram nodeSuman Anna2019-07-261-0/+14
| | | | | | | | | Create a ft_board_setup() api that gets called as part of DT fixup before jumping to kernel. In this ft_board_setup() call fdt_fixup_msmc_ram that update msmc sram node. Signed-off-by: Suman Anna <s-anna@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
* board: ti: j721e: Add board support for j721e evmLokesh Vutla2019-07-263-0/+131
| | | | | | | | Add board specific initialization for j721e evm Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com> Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
* net: davinci_emac: convert to using the driver modelBartosz Golaszewski2019-07-251-2/+1
| | | | | | | | | | Now that we removed all legacy boards selecting TI_EMAC we can completely convert the driver code to using the driver model. This patch also updates all remaining users of davinci_emac. Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com> Tested-by: Adam Ford <aford173@gmail.com> #am3517-evm & da850-evm Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
* board: ti: am654: Use EEPROM-based board detectionAndreas Dannenberg2019-07-172-0/+248
| | | | | | | | | | | | | | | | | | | | | | | | | | The TI AM654x EVM base board and the associated daughtercards have on- board I2C-based EEPROMs containing board configuration data. Use the board detection infrastructure introduced earlier to do the following: 1) Parse the AM654x EVM base board EEPROM and populate items like board name and MAC addresses into the TI common EEPROM data structure residing in SRAM scratch space 2) Check for presence of daughter card(s) by probing the associated presence signals via an I2C-based GPIO expander. Then, if such a card is found, parse the data such as additional Ethernet MAC addresses from its on-board EEPROM and populate into U-Boot accordingly 3) Dynamically create an U-Boot ENV variable called overlay_files containing a list of daugherboard-specific DTB overlays based on daughercards found. This patch adds support for the AM654x base board ("AM6-COMPROCEVM") as well as for the IDK ("AM6-IDKAPPEVM"), OLDI LCD ("OLDI-LCD1EVM") PCIe/USB3.0 ("SER-PCIEUSBEVM"), 2 Lane PCIe/USB2.0 ("SER-PCIE2LEVM"), and general purpuse ("AM6-GPAPPEVM") daughtercards. Signed-off-by: Andreas Dannenberg <dannenberg@ti.com> Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
* ti: common: am6: Add support for setting MAC addressesAndreas Dannenberg2019-07-172-0/+44
| | | | | | | | | | | | The AM654x EVM based on the TI K3 family of SoCs has an updated board detection EEPROM structure that contains a TLV record of dedicated MAC addresses rather than a range of MAC addresses as it was used on earlier platforms such as DRA7. Add a basic function that allows us setting up Ethernet MAC addresses into the U-Boot environment based on the MAC address record contained in the common TI EEPROM structure. Signed-off-by: Andreas Dannenberg <dannenberg@ti.com> Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
* ti: common: am6: Add support for board description EEPROMAndreas Dannenberg2019-07-172-0/+408
| | | | | | | | | | | | | | The AM654x EVM based on the TI K3 family of SoCs have an updated board detection EEPROM structure, now comprising variable-sized TLV-type records, containing a superset of what is already being provided on earlier platforms such as DRA7. Add basic support for parsing the new data structures contained on the base board into the common TI EEPROM structure while also providing infrastructure that can be used later on to parse data from additional EEPROMs such as the ones that are used on daughtercards for this platform. Signed-off-by: Andreas Dannenberg <dannenberg@ti.com> Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
* am65x: README: Add eMMC layout and flash instructionsFaiz Abbas2019-07-171-0/+52
| | | | | | | | | | Add instructions for flashing boot images to the eMMC with a layout of the address where each image needs to be flashed. Also add instructions to flash filesystem partition in user partition and boot kernel from the rootfs. Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
* armV7R: K3: am654: Load SYSFW binary and config from boot mediaAndreas Dannenberg2019-07-171-0/+1
| | | | | | | | | Use the System Firmware (SYSFW) loader framework to load and start the SYSFW as part of the AM654 early initialization sequence. While at it also initialize the WKUP_UART0 pinmux as it is used by SYSFW to print diagnostic messages. Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
* ARM: omap3: evm: Enable DM_USB in defconfigDerald D. Woods2019-07-131-31/+0
| | | | | | | | | | | | | | | | | This addresses the following warning message: ===================== WARNING ====================== This board does not use CONFIG_DM_USB. Please update the board to use CONFIG_DM_USB before the v2019.07 release. Failure to update by the deadline may result in board removal. See doc/driver-model/MIGRATION.txt for more info. ==================================================== As USB support for older OMAP3 SoC's improves, OMAP3 EVM can be readily adapted. There is some additional 'gpio-hog' support needed to fully setup USB in a similar manner to Linux. Signed-off-by: Derald D. Woods <woods.technical@gmail.com>
* board: am335x/mux: configure the pins for 8-bit data transfer on MMC1Jean-Jacques Hiblot2019-06-051-0/+4
| | | | | | | This is required for proper operation of the 8-bit data transfers. This fixes transient errors seen on BeagleBone Black. Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
* ARM: k2g-ice: Add pinmux support for rgmii interfaceMurali Karicheri2019-05-081-9/+9
| | | | | | | | | | | | | | This add pinmux configuration for rgmii interface so that network driver can be supported on K2G ICE boards. The pinmux configurations for this are generated using the pinmux tool at https://dev.ti.com/pinmux/app.html#/default As this required some BUFFER_CLASS definitions, same is re-used from the linux defnitions in include/dt-bindings/pinctrl/keystone.h Signed-off-by: Murali Karicheri <m-karicheri2@ti.com> Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
* ARM: k2g-gp-evm: update to rgmii pinmux configurationMurali Karicheri2019-05-081-9/+9
| | | | | | | | | | This patch updates pinmux configuration for K2G GP EVM based on data generated by the pinmux tool at https://dev.ti.com/pinmux/app.html#/default Signed-off-by: Murali Karicheri <m-karicheri2@ti.com> Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
* board: ti: am43xx: Enable hardware levelingBrad Griffis2019-05-051-1/+1
| | | | | | | | | | | Remove the RDLVL_MASK, RDLVLGATE_MASK, WRLVL_MASK & enable PHY_INVERT_CLKOUT to enable Hardware leveling for am437x as recommended by EMIF Tools app note: http://www.ti.com/lit/an/sprac70/sprac70.pdf Signed-off-by: Brad Griffis <bgriffis@ti.com> Signed-off-by: Keerthy <j-keerthy@ti.com>
* board: ti: am654: select SYS_DISABLE_DCACHE_OPS for arm64 buildVignesh Raghavendra2019-05-051-0/+1
| | | | | | | | AM654 SoC is IO coherent wrt A53 cores, therefore enable SYS_DISABLE_DCACHE_OPS to avoid cache operations in A53 SPL/U-Boot. Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
* board: am335x: Drop duplicate pinmux configurationPaul Barker2019-05-031-1/+0
| | | | | | | | | | | | | | In commit ad6054f1fe128f797b6eb2964afca6674b584785 where support for the Sancloud BeagleBone Enhanced (BBE) was added, new conditional configuration of either MII pin muxing or RGMII pin muxing is done depending on the board type. However, the old call to set up MII pin muxing was not removed. This may result in misconfiguration of the pin muxing for the BBE or duplicate configuration for other boards and so we remove this obsolete call. Signed-off-by: Paul Barker <paul.barker@sancloud.co.uk>
* board: ti: am335x: Remove non DM_ETH codeFaiz Abbas2019-04-121-151/+0
| | | | | | | With DM_ETH enabled in am335x devices, remove all the unused non-DM code. Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
* board: ti: am335x: Add platdata for cpsw in SPLFaiz Abbas2019-04-121-0/+49
| | | | | | | The SPL image overflows when cpsw dt nodes are added and SPL_OF_CONTROL is enabled. Use static platdata instead to save space. Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
* board: ti: am65x: Enable fixing up msmc sram nodeLokesh Vutla2019-04-121-0/+14
| | | | | | | | Create a ft_board_setup() api that gets called as part of DT fixup before jumping to kernel. In this ft_board_setup() call fdt_fixup_msmc_ram that update msmc sram node. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
* arm: dra7: Allow NAND to be enabled on DRA71x EVM.Franklin S Cooper Jr2019-04-121-0/+56
| | | | | | | | | | If SW 8 pins 0 and 1 indicate that NAND should be enabled then the pins pinmux must be reconfigured for NAND mode. Therefore, enable NAND by reconfiguring the pinmux. Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com> Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
* board: ti: dra71: Add pinmux settings for NAND on DRA71x EVMFranklin S Cooper Jr2019-04-121-16/+44
| | | | | | | | | | | | | | By default VOUT3 occupies the pins required for NAND. Therefore, create a seperate entry that can be use to reconfigure these pins to work for NAND. On the EVM SWITCH 8 pins 0 and 1 will be used to determine if NAND is enabled or not. For NAND to be selected pin 0 should be on and pin 1 should be off. Any other combination will assume NAND shouldn't be enabled. Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com> Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
* ARM: k2g: add a workaround to reset the phyMurali Karicheri2019-04-121-0/+15
| | | | | | | | | This patch adds a workaround to reset the phy one time during boot using GPIO0 pin 10 to make sure, the Phy latches the configuration from the input pins correctly. Signed-off-by: Murali Karicheri <m-karicheri2@ti.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
* ARM: k2g-gp-evm: update to rgmii pinmux configurationMurali Karicheri2019-04-121-15/+17
| | | | | | | | | This patch updates pinmux configuration for K2G GP EVM based on data generated by the pinmux tool at https://dev.ti.com/pinmux/app.html#/default Signed-off-by: Murali Karicheri <m-karicheri2@ti.com> Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
* ARM: k2g-ice: Add pinmux support for rgmii interfaceMurali Karicheri2019-04-121-0/+19
| | | | | | | | | | | | | | This add pinmux configuration for rgmii interface so that network driver can be supported on K2G ICE boards. The pinmux configurations for this are generated using the pinmux tool at https://dev.ti.com/pinmux/app.html#/default As this required some BUFFER_CLASS definitions, same is re-used from the linux defnitions in include/dt-bindings/pinctrl/keystone.h Signed-off-by: Murali Karicheri <m-karicheri2@ti.com> Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
* board: ti: Move fastboot functions out of TI_SECURE_DEVICE ifdefAndrew F. Davis2019-03-222-20/+20
| | | | | | | | | | When these were moved from mach-omap2 to board files they got placed inside TI_SECURE_DEVICE ifdef block, they are not secure only, move them up and out. Fixes: 413b90777f8d ("ti: fastboot: Move weak overrides to board files") Signed-off-by: Andrew F. Davis <afd@ti.com> Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
* ARM: omap3: evm: Update DM SPL supportDerald D. Woods2019-02-191-12/+0
| | | | | | | | | | | | | - Switch to using the omap3-u-boot.dtsi file for needed properties - Enable SPL_OF_CONTROL This commit is based on the following series: https://patchwork.ozlabs.org/project/uboot/list/?series=92472 https://patchwork.ozlabs.org/project/uboot/list/?series=92462 Signed-off-by: Derald D. Woods <woods.technical@gmail.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* omap3_beagle: Update for DM SPL supportTom Rini2019-02-191-12/+0
| | | | | | | | | | | - Switch to using the omap3-u-boot.dtsi file for needed properties. - Remove a few SPL features to free up more SRAM space. - Switch CONFIG_SYS_TEXT_BASE to the normal default, we don't need to worry about X-Loader at this point anymore. - A few related updates to SPL options as part of switching to DM SPL. Signed-off-by: Tom Rini <trini@konsulko.com> Tested-by: Derald D. Woods <woods.technical@gmail.com>
* configs: Remove am43xx_evm_ethboot_defconfigVignesh R2019-01-181-1/+0
| | | | | | | | | am43xx_evm_ethboot_defconfig is not being actively used and has not been moved to DM or DT. Also, ethboot cannot be tested on AM43xx EVM as such due EVM limitations. Therefore delete it. Signed-off-by: Vignesh R <vigneshr@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* configs: Remove unused am335x_evm defconfigsVignesh R2019-01-181-3/+0
| | | | | | | | These defconfigs don't seem be actively used any more, and have not been moved to adapt DM or DT. Therefore delete them. Signed-off-by: Vignesh R <vigneshr@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* board: ti: am43xx: turn on USB clocksJean-Jacques Hiblot2018-12-141-0/+22
| | | | | | | Enable USB clocks in late init stage to support ports under DM_USB. Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* board: ks2_evm: Enable the USB clocks if DM_USB is usedJean-Jacques Hiblot2018-12-141-0/+12
| | | | | Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* Merge branch 'master' of git://git.denx.de/u-boot-i2cTom Rini2018-12-106-84/+136
|\ | | | | | | | | - DM_I2C_COMPAT removal for all ti platforms from Jean-Jacques Hiblot - Fix in i2c command help output from Chirstoph Muellner.
| * am57xx: remove non-DM I2C codeJean-Jacques Hiblot2018-12-101-33/+3
| | | | | | | | | | | | | | | | | | am57xx configs uses DM_I2C both in SPL and u-boot. Remove code for non-DM I2C support. Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Heiko Schocher <hs@denx.de>
generated by cgit (git 2.34.1) at 2024-10-05 19:00:30 +0000