summaryrefslogtreecommitdiffstats
path: root/board/htkw
Commit message (Collapse)AuthorAgeFilesLines
* omap3: fix pinmux for mcx boardStefano Babic2014-02-211-2/+0
| | | | | | | | | | New hardware version cannot recognize the SD-Card because the SYS_NRESWARM, set as GPIO, does not guarantee the required reset time. Change the pin function back to enable the SYS_NRESWARM signal driven by the SOC. Signed-off-by: Stefano Babic <sbabic@denx.de>
* board: arm: convert makefiles to Kbuild styleMasahiro Yamada2013-11-011-18/+1
| | | | | | | | | | | | Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Albert ARIBAUD <albert.u.boot@aribaud.net> Cc: Andreas Bießmann <andreas.devel@googlemail.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Prafulla Wadaskar <prafulla@marvell.com> Cc: Minkyu Kang <mk7.kang@samsung.com> Cc: Vipin Kumar <vipin.kumar@st.com> Cc: Tom Warren <twarren@nvidia.com> Cc: Tom Rini <trini@ti.com>
* usb: ehci-hcd: add enum usb_init_type parameter to ehci_hcd_init.Troy Kisky2013-10-201-1/+2
| | | | | | | This paramter will later be used to initialize OTG ports in host or device mode. Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
* usb: new board-specific USB init interfaceMateusz Zalega2013-10-201-1/+1
| | | | | | | | | | | | | | This commit unifies board-specific USB initialization implementations under one symbol (usb_board_init), declaration of which is available in usb.h. New API allows selective initialization of USB controllers whenever needed. Signed-off-by: Mateusz Zalega <m.zalega@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Reviewed-by: Lukasz Majewski <l.majewski@samsung.com> Cc: Marek Vasut <marex@denx.de> Cc: Lukasz Majewski <l.majewski@samsung.com>
* Add GPL-2.0+ SPDX-License-Identifier to source filesWolfgang Denk2013-07-243-39/+3
| | | | | | Signed-off-by: Wolfgang Denk <wd@denx.de> [trini: Fixup common/cmd_io.c] Signed-off-by: Tom Rini <trini@ti.com>
* ARM: OMAP2+: Rename asm/arch/clocks.h asm/arch/clock.hLokesh Vutla2013-06-101-1/+1
| | | | | | | To be consistent with other ARM platforms, renaming asm/arch-omap*/clocks.h to asm/arch-omap*/clock.h Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
* omap3: allow dynamic selection of gfx_formatNikita Kiryanov2013-03-081-0/+1
| | | | | | | | | | | | | | | | | Currently, omap3_dss_panel_config() sets gfx_format to a value that is hardcoded in the code. This forces anyone who wants to use a different gfx_format to make adjustments after calling omap3_dss_panel_config(). This could be avoided if the value of gfx_format were parameterized as input for omap3_dss_panel_config(). Make gfx_format a field in struct panel_config, and update existing structs to set this field to the value that was originally hard coded. Cc: Wolfgang Denk <wd@denx.de> Cc: Jeroen Hofstee <jeroen@myspectrum.nl> Cc: Tom Rini <trini@ti.com> Cc: Anatolij Gustschin <agust@denx.de> Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il> Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
* omap_hsmmc: add driver check for write protectionNikita Kiryanov2013-03-081-1/+1
| | | | | | | | Add check for write protection in omap mmc driver. Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il> Signed-off-by: Igor Grinberg <grinberg@compulab.co.il> Reviewed-by: Tom Rini <trini@ti.com>
* omap_hsmmc: implement driver check for card detectionNikita Kiryanov2013-03-081-1/+1
| | | | | | | Implement driver check for card detection. Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il> Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
* OMAP3: add video support to the mcx boardStefano Babic2012-10-252-0/+43
| | | | | | | Add video support to the board with the display focaltech etm070003dh6. Signed-off-by: Stefano Babic <sbabic@denx.de>
* OMAP3: mcx: updated to new hardware revisionStefano Babic2012-10-252-17/+4
| | | | | | | | Some GPIOs differ in the new revision board. Previous revision are considered obsolete and they will not anymore supported. Signed-off-by: Stefano Babic <sbabic@denx.de>
* OMAP3: updated pinmux and environment for new revision of mcx boardStefano Babic2012-10-251-13/+13
| | | | | | | The mcx board was slightly modified and the pinmux must be updated. There is no need to support the old board, that becomes obsolete. Signed-off-by: Stefano Babic <sbabic@denx.de>
* usb: ehci: rework to take advantage of new lowlevel interfaceLucas Stach2012-10-151-3/+3
| | | | | | | | | | | | | | Kill off ehci-core.h It was used to specify some static controller data. To support more than one controller being active at any time we have to carry the controller data ourselfes. Change the ehci interface accordingly. NOTE: OMAP implemented the ehci stuff a bit backwards and should be fixed to do the same thing as other platforms. But the change for now is at least compile clean. Signed-off-by: Lucas Stach <dev@lynxeye.de> Reviewed-by: Marek Vasut <marex@denx.de>
* OMAP3: mcx: read hot-water-button after resetStefano Babic2012-09-011-0/+23
| | | | | | | Detect hot-water-button to start a differnt image. Signed-off-by: Stefano Babic <sbabic@denx.de> CC: Tom Rini <trini@ti.com>
* OMAP3: mcx: set pinmux for uart4Stefano Babic2012-09-011-3/+8
| | | | | Signed-off-by: Stefano Babic <sbabic@denx.de> CC: Tom Rini <trini@ti.com>
* omap3: Introduce weak misc_init_rTom Rini2012-05-151-11/+0
| | | | | | | | | | | | | Introduce a __weak misc_init_r function that just runs dieid_num_r(). Remove misc_init_r from cm_t35, mcx, omap3_logic and mt_ventoux as this was all they did for misc_init_r. Cc: Igor Grinberg <grinberg@compulab.co.il> Cc: Ilya Yanok <yanok@emcraft.com> Cc: Peter Barada <peter.barada@logicpd.com> Cc: Stefano Babic <sbabic@denx.de> Signed-off-by: Tom Rini <trini@ti.com> Acked-by: Igor Grinberg <grinberg@compulab.co.il>
* ARM:OMAP+:MMC: Add parameters to MMC initJonathan Solnit2012-05-151-1/+1
| | | | | | | | | | Add parameters to the OMAP MMC initialization function so the board can mask host capabilities and set the maximum clock frequency. While the OMAP supports a certain set of MMC host capabilities, individual boards may be more restricted and the OMAP may need to be configured to match the board. The PRG_SDMMC1_SPEEDCTRL bit in the OMAP3 is an example. Signed-off-by: Jonathan Solnit <jsolnit@gmail.com>
* mcx: support for HTKW mcx boardIlya Yanok2012-02-123-0/+558
This patch adds support for the HTKW mcx AM3517-based board. Serial, Ethernet, NAND, MMC, RTC, EHCI USB host and both NAND and MMC SPLs are supported. Signed-off-by: Ilya Yanok <yanok@emcraft.com> Signed-off-by: Stefano Babic <sbabic@denx.de> CC: Tom Rini <tom.rini@gmail.com> Cc: Detlev Zundel <dzu@denx.de> Acked-by: Igor Grinberg <grinberg@compulab.co.il>
generated by cgit (git 2.34.1) at 2024-11-19 05:13:24 +0000