summaryrefslogtreecommitdiffstats
path: root/arch/arm/dts/armada-37xx.dtsi
Commit message (Collapse)AuthorAgeFilesLines
* watchdog: Add support for Armada 37xx CPU watchdogMarek Behún2018-05-141-0/+6
| | | | | | | | | | | | | | This adds support for the CPU watchdog found on Marvell Armada 37xx SoCs. There are 4 counters which can be set as CPU watchdog counters. This driver uses the second counter (ID 1, counting from 0) (Marvell's Linux also uses second counter by default). In the future it could be adapted to use other counters, with definition in the device tree. Signed-off-by: Marek Behun <marek.behun@nic.cz> Signed-off-by: Stefan Roese <sr@denx.de>
* spi: mvebu_a3700_spi: Use Armada 37xx clk driver for SPI clock frequencyMarek Behún2018-05-141-2/+2
| | | | | | | | | | | | Since now we have driver for clocks on Armada 37xx, use it to determine SQF clock frequency for the SPI driver. Also change the default config files for Armada 37xx devices so that the clock driver is enabled by default, otherwise the SPI driver cannot be enabled. Signed-off-by: Marek Behun <marek.behun@nic.cz> Signed-off-by: Stefan Roese <sr@denx.de>
* driver: clk: Add support for clocks on Armada 37xxMarek Behún2018-05-141-0/+20
| | | | | | | | | | | | | | | | | | | | | | The drivers are based on Linux driver by Gregory Clement. The TBG clocks support only the .get_rate method. - since setting rate is not supported, the driver computes the rates when probing and so subsequent calls to the .get_rate method do not read the corresponding registers again The peripheral clocks support methods .get_rate, .enable and .disable. - the .set_parent method theoretically could be supported on some clocks (the parent would have to be one of the TBG clocks) - the .set_rate method would have to try all the divider values to find the best approximation of a given rate, and it doesn't seem like this should be needed in U-Boot, therefore not implemented Signed-off-by: Marek Behun <marek.behun@nic.cz> Reviewed-by: Stefan Roese <sr@denx.de> Signed-off-by: Stefan Roese <sr@denx.de>
* phy: marvell: a3700: Use comphy_mux on Armada 37xx.Marek Behún2018-05-141-2/+3
| | | | | | | | | | | | | | | Lane 0 supports SGMII1 and USB3. Lane 1 supports SGMII0 and PEX0. Lane 2 supports SATA0 and USB3. This is needed for Armada 37xx. This introduces new device tree bindings. AFAIK there is currently no driver for Armada 37xx comphy in Linux. When such a driver will be pushed into Linux, this will need to be rewritten accordingly. Signed-off-by: Marek Behun <marek.behun@nic.cz> Signed-off-by: Stefan Roese <sr@denx.de>
* arm64: a37xx: dts: enable pcie portWilson Ding2018-03-301-0/+16
| | | | | | | | | | | This patch enabled PCIe port on both devel-board and espressobin board. Cc: Simon Glass <sjg@chromium.org> Cc: Stefan Roese <sr@denx.de> Signed-off-by: Wilson Ding <dingwei@marvell.com> Signed-off-by: Ken Ma <make@marvell.com> Signed-off-by: Stefan Roese <sr@denx.de>
* Revert "arm64: a37xx: dts: Add pin control nodes to DT"Ken Ma2018-03-301-14/+0
| | | | | | | | | | | The commit "arm64: mvebu: Add pinctrl nodes for Armada 3700" has added new pinctrl nodes. This reverts commit f7cab0f95b05ec6a66fe4796b9ad44406d0cc864. Cc: Simon Glass <sjg@chromium.org> Cc: Stefan Roese <sr@denx.de> Signed-off-by: Ken Ma <make@marvell.com> Signed-off-by: Stefan Roese <sr@denx.de>
* arm64: a37xx: dts: Correct mpp definitionsKen Ma2018-03-301-1/+6
| | | | | | | | | | | | | | | | This patch corrects below mpp definitions for armada 3720 DB board and ESPRESSOBin board: - "smi" pins group is added and "smi" function is set for eth0; - Now pcie pins are used as gpio to implement PCIe function in hardware, so "pcie" group function is changed to "gpio". Reviewed-on: http://vgitil04.il.marvell.com:8080/43287 Reviewed-by: Hua Jing <jinghua@marvell.com> Tested-by: iSoC Platform CI <ykjenk@marvell.com> Cc: Simon Glass <sjg@chromium.org> Cc: Stefan Roese <sr@denx.de> Signed-off-by: Ken Ma <make@marvell.com> Signed-off-by: Stefan Roese <sr@denx.de>
* arm64: a37xx: dts: Fix the number of GPIO on south bridgeKen Ma2018-03-301-1/+1
| | | | | | | | | | | | | | The number of pins in South Bridge is 30 and not 29. There is a fix for the driver for the pinctrl, but a fix is also need at device tree level for the GPIO. Reviewed-on: http://vgitil04.il.marvell.com:8080/43286 Reviewed-by: Hua Jing <jinghua@marvell.com> Tested-by: iSoC Platform CI <ykjenk@marvell.com> Cc: Simon Glass <sjg@chromium.org> Cc: Stefan Roese <sr@denx.de> Signed-off-by: Ken Ma <make@marvell.com> Signed-off-by: Stefan Roese <sr@denx.de>
* arm64: a37xx: dts: Add additional pinctrl definitionKen Ma2018-03-301-0/+14
| | | | | | | | | | | | | | Add mmc pins, pcie pins and sdio pins definition and do these pins' configuration for DB board and espressobin board; Add uart2 pins configuration for DB board. Reviewed-on: http://vgitil04.il.marvell.com:8080/40914 Reviewed-by: Wilson Ding <dingwei@marvell.com> Tested-by: Wilson Ding <dingwei@marvell.com> Cc: Simon Glass <sjg@chromium.org> Cc: Stefan Roese <sr@denx.de> Signed-off-by: Ken Ma <make@marvell.com> Signed-off-by: Stefan Roese <sr@denx.de>
* arm64: a37xx: dts: add gpio head file includingKen Ma2018-03-301-0/+1
| | | | | | | Cc: Simon Glass <sjg@chromium.org> Cc: Stefan Roese <sr@denx.de> Signed-off-by: Ken Ma <make@marvell.com> Signed-off-by: Stefan Roese <sr@denx.de>
* arm64: mvebu: armada37xx: add pinctrl definitionGregory CLEMENT2017-05-311-0/+31
| | | | | | | | | | | Start to populate the device tree of the Armada 37xx with the pincontrol configuration used on the board providing a dts. Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com> Signed-off-by: Stefan Roese <sr@denx.de> Cc: Gregory CLEMENT <gregory.clement@free-electrons.com> Cc: Konstantin Porotchkin <kostap@marvell.com> Cc: Nadav Haklai <nadavh@marvell.com>
* arm64: mvebu: Add pinctrl nodes for Armada 3700Gregory CLEMENT2017-05-311-0/+42
| | | | | | | | | | | | | | | | | Add the nodes for the two pin controller present in the Armada 37xx SoCs. Initially the node was named gpio1 using the same name that for the register range in the datasheet. However renaming it pinctr_nb (nb for North Bridge) makes more sens. Minor changes for U-Boot because of the slightly different dts version done by Stefan Roese. Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com> Signed-off-by: Stefan Roese <sr@denx.de> Cc: Gregory CLEMENT <gregory.clement@free-electrons.com> Cc: Konstantin Porotchkin <kostap@marvell.com> Cc: Nadav Haklai <nadavh@marvell.com>
* arm64: a37xx: dts: Add pin control nodes to DTKonstantin Porotchkin2017-03-231-0/+14
| | | | | | | | | | | Add pin control nodes for North and South bridges to Armada-37xx DT Signed-off-by: Konstantin Porotchkin <kostap@marvell.com> Cc: Stefan Roese <sr@denx.de> Cc: Igal Liberman <igall@marvell.com> Cc: Nadav Haklai <nadavh@marvell.com> Signed-off-by: Stefan Roese <sr@denx.de>
* arm64: mvebu: Armada 3700: Add SDHCI device tree nodesStefan Roese2017-01-251-0/+16
| | | | | | | | | | | | | | | This patch adds the SDHCI device tree nodes to the Armada 3700 dtsi file. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Nadav Haklai <nadavh@marvell.com> Cc: Kostya Porotchkin <kostap@marvell.com> Cc: Wilson Ding <dingwei@marvell.com> Cc: Victor Gu <xigu@marvell.com> Cc: Hua Jing <jinghua@marvell.com> Cc: Terry Zhou <bjzhou@marvell.com> Cc: Hanna Hawa <hannah@marvell.com> Cc: Haim Boot <hayim@marvell.com>
* arm64: mvebu: Armada 3700: Add USB device tree nodesStefan Roese2016-09-271-0/+6
| | | | | | | | | | | | | | | This patch adds the USB device tree nodes that are still missing to the Armada 3700 dts files. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Nadav Haklai <nadavh@marvell.com> Cc: Kostya Porotchkin <kostap@marvell.com> Cc: Wilson Ding <dingwei@marvell.com> Cc: Victor Gu <xigu@marvell.com> Cc: Hua Jing <jinghua@marvell.com> Cc: Terry Zhou <bjzhou@marvell.com> Cc: Hanna Hawa <hannah@marvell.com> Cc: Haim Boot <hayim@marvell.com>
* arm64: mvebu: Armada 3700: Add COMPHY device tree nodesStefan Roese2016-09-271-0/+9
| | | | | | | | | | | | | | | This patch adds the COMPHY device tree nodes that are still missing to the Armada 3700 dts files. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Nadav Haklai <nadavh@marvell.com> Cc: Kostya Porotchkin <kostap@marvell.com> Cc: Wilson Ding <dingwei@marvell.com> Cc: Victor Gu <xigu@marvell.com> Cc: Hua Jing <jinghua@marvell.com> Cc: Terry Zhou <bjzhou@marvell.com> Cc: Hanna Hawa <hannah@marvell.com> Cc: Haim Boot <hayim@marvell.com>
* arm64: mvebu: Armada 3700: Add I2C device tree nodesStefan Roese2016-09-271-0/+6
| | | | | | | | | | | | | | | This patch adds the I2C device tree nodes that are still missing to the Armada 3700 dts files. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Nadav Haklai <nadavh@marvell.com> Cc: Kostya Porotchkin <kostap@marvell.com> Cc: Wilson Ding <dingwei@marvell.com> Cc: Victor Gu <xigu@marvell.com> Cc: Hua Jing <jinghua@marvell.com> Cc: Terry Zhou <bjzhou@marvell.com> Cc: Hanna Hawa <hannah@marvell.com> Cc: Haim Boot <hayim@marvell.com>
* arm64: mvebu: Armada 3700: Add ethernet device tree nodesStefan Roese2016-09-271-0/+12
| | | | | | | | | | | | | | | This patch adds the ethernet device tree nodes that are still missing to the Armada 3700 dts files. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Nadav Haklai <nadavh@marvell.com> Cc: Kostya Porotchkin <kostap@marvell.com> Cc: Wilson Ding <dingwei@marvell.com> Cc: Victor Gu <xigu@marvell.com> Cc: Hua Jing <jinghua@marvell.com> Cc: Terry Zhou <bjzhou@marvell.com> Cc: Hanna Hawa <hannah@marvell.com> Cc: Haim Boot <hayim@marvell.com>
* arm64: mvebu: Armada 3700: Add SPI device tree nodesStefan Roese2016-09-271-0/+11
| | | | | | | | | | | | | | | | This patch adds the SPI device tree nodes that are still missing to the Armada 3700 dts files. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Nadav Haklai <nadavh@marvell.com> Cc: Kostya Porotchkin <kostap@marvell.com> Cc: Wilson Ding <dingwei@marvell.com> Cc: Victor Gu <xigu@marvell.com> Cc: Hua Jing <jinghua@marvell.com> Cc: Terry Zhou <bjzhou@marvell.com> Cc: Hanna Hawa <hannah@marvell.com> Cc: Haim Boot <hayim@marvell.com> Reviewed-by: Jagan Teki <jteki@openedev.com>
* arm64: mvebu: Armada 3700: Add Armada 37xx dts filesStefan Roese2016-09-271-0/+145
This patch integrates the Armada 3700 dts files from the latest submission on the linux-arm-kernel mailing list. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Nadav Haklai <nadavh@marvell.com> Cc: Kostya Porotchkin <kostap@marvell.com> Cc: Wilson Ding <dingwei@marvell.com> Cc: Victor Gu <xigu@marvell.com> Cc: Hua Jing <jinghua@marvell.com> Cc: Terry Zhou <bjzhou@marvell.com> Cc: Hanna Hawa <hannah@marvell.com> Cc: Haim Boot <hayim@marvell.com>
generated by cgit (git 2.34.1) at 2024-11-19 09:36:56 +0000