summaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAgeFilesLines
...
| * | | mx51evk: Add myself as maintainerFabio Estevam2021-03-011-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | I would like to help supporting this board, so add myself as a maintainer. Signed-off-by: Fabio Estevam <festevam@gmail.com>
| * | | mx51evk: Convert to driver modelFabio Estevam2021-03-014-194/+22
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Make the conversion to driver model as it is mandatory. Tested booting the Linux kernel from the SD card. Signed-off-by: Fabio Estevam <festevam@gmail.com>
| * | | imx51-babbage: Import devicetree files from LinuxFabio Estevam2021-03-013-0/+2148
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Import the imx51-babbage devicetree files from Linux kernel version 5.11-rc7. This is in preparation for converting the mx51evk_defconfig target to driver model. Signed-off-by: Fabio Estevam <festevam@gmail.com>
| * | | mmc: fsl_esdhc_imx: Add a compatible for i.MX51Fabio Estevam2021-03-011-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add a compatible for i.MX51 so that i.MX51 can use this driver via driver model. Signed-off-by: Fabio Estevam <festevam@gmail.com> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
| * | | mx53loco: Add myself as maintainerFabio Estevam2021-03-011-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | I would like to help supporting this board, so add myself as a maintainer. Signed-off-by: Fabio Estevam <festevam@gmail.com>
| * | | ARM: dts: imx53-qsb: Describe the esdhc1 card detect pinFabio Estevam2021-03-011-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The micro SD card slot uses GPIO3_13 as card detect pin, so describe it in the devicetree. This was noticed when converting imx53-qsb board to driver model in U-Boot as the micro SD card was not getting detected. After this change it is possible to load the dtb and zImage from the SD card and boot Linux. Signed-off-by: Fabio Estevam <festevam@gmail.com>
| * | | mx53loco: Convert to driver modelFabio Estevam2021-03-014-133/+20
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Make the conversion to driver model as it is mandatory. Remove the SATA support for now as the i.MX53 support has not been added yet. Signed-off-by: Fabio Estevam <festevam@gmail.com>
| * | | imx53-qsb: Import devicetree files from LinuxFabio Estevam2021-03-012-0/+496
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Import the imx53-qsb devicetree files from Linux kernel version 5.11-rc7. This is in preparation for converting the mx53loco_defconfig target to driver model. Signed-off-by: Fabio Estevam <festevam@gmail.com>
| * | | board: toradex: move RGMII delays to PHY sideOleksandr Suvorov2021-03-014-7/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The RGMII link delays can be set on either MAC or PHY side. Set the rgmii-id PHY mode for FEC and remove FEC_ENET_ENABLE_.XC_DELAY setting, so that these definitions aren't used anymore throughout the U-Boot. Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com> Reviewed-by: Fabio Estevam <festevam@gmail.com>
| * | | ARM: imx8: Add missing FEC ENET quirk for i.MX8/i.MX8XOleksandr Suvorov2021-03-018-8/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Both NXP SoCs i.MX8 and i.MX8X have ENET gigabit MAC. Define FEC_QUIRK_ENET_MAC for the imx8 platform and remove this definition from configs of boards, based on MX8/MX8X. Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com> Acked-by: Marek Vasut <marex@denx.de> Reviewed-By: Ramon Fried <rfried.dev@gmail.com> Acked-by: Oliver Graute <oliver.graute@kococonnector.com> Reviewed-by: Fabio Estevam <festevam@gmail.com>
| * | | Respect that some compression algos can be enabled separately for SPLFrieder Schrempf2021-03-011-6/+18
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Some compression algorithms currently can be enabled for SPL and U-Boot proper separately. Therefore take into account USE_HOSTCC is well as CONFIG_IS_ENABLED() in these cases to prevent compiling these functions in case of a host tool build. Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de> Signed-off-by: Tim Harvey <tharvey@gateworks.com>
| * | | thermal: imx_tmu: enable monitoring and default alert/criticalTim Harvey2021-03-011-0/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Set default critical/alert temperature and enabling monoitoring. Without calling imx_tmu_enable_msite() monitoring will not be enabled and read_temperature will return 0. Additionally without setting alert temperature will cause imx_tmu_get_temp() to spin indefiniately thinking the system needs to cool. This resolves the board spinning endlessly when enabling IMX_TMU in the SPL. Reviewed-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Tim Harvey <tharvey@gateworks.com>
| * | | ARM: mx6: Add function to set serial#Sean Anderson2021-03-011-0/+37
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The serial number OTP is similar to the imx7 version, except that the register names are different. This also sets serial# directly, instead of providing board_get_serial. Signed-off-by: Sean Anderson <sean.anderson@seco.com> Reviewed-by: Tom Rini <trini@konsulko.com>
| * | | ARM: imx6: mx6sabre-common: Search for boot components in /boot tooMarek Vasut2021-03-011-3/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Some root filesystem configurations do not have separate /boot partition, but rather place kernel, DT, scripts into /boot directory. Search the /boot directory for these boot components in case they are not found in /, which is the old behavior. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Fabio Estevam <festevam@gmail.com> Cc: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Ye Li <ye.li@nxp.com> Cc: uboot-imx <uboot-imx@nxp.com> Reviewed-by: Peng Fan <peng.fan@nxp.com>
| * | | ARM: imx6: mx6sabre-common: Replace fatload with FS_GENERIC loadMarek Vasut2021-03-011-3/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Replace filesystem specific fatload command with a filesystem agnostic load command, so the board can boot from e.g. ext4 too. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Fabio Estevam <festevam@gmail.com> Cc: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Ye Li <ye.li@nxp.com> Cc: uboot-imx <uboot-imx@nxp.com> Reviewed-by: Peng Fan <peng.fan@nxp.com>
| * | | ARM: imx6: dh-imx6: Drop the SF hunk in configMarek Vasut2021-02-271-6/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | There is now CONFIG_SPL_DM_SPI{,_FLASH}, however keeping CONFIG_DM_SPI{,_FLASH} enabled in SPL seems to grow the SPL by a couple of bytes: text data bss dec hex filename - 34069 1568 96 35733 8b95 spl/u-boot-spl + 34075 1568 96 35739 8b9b spl/u-boot-spl In either case, the binary is bootable, so remove the part in board config. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Andreas Geisreiter <ageisreiter@dh-electronics.de> Cc: Jagan Teki <jagan@amarulasolutions.com> Cc: Ludwig Zenz <lzenz@dh-electronics.de> Cc: Stefano Babic <sbabic@denx.de> Cc: Tom Rini <trini@konsulko.com>
| * | | ARM: imx6: dh-imx6: Enable support for applying DTOMarek Vasut2021-02-271-1/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Enable DTO support to make it possible to boot fitImage with DTOs embedded in them. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Stefano Babic <sbabic@denx.de>
| * | | ARM: imx: Revert "dh_imx6: Switch to full DM-aware"Marek Vasut2021-02-272-3/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This reverts commit 03a673cf49e ("dh_imx6: Switch to full DM-aware"). According to discussion [1], the patch is known to break the dh_imx6 board, however it made it upstream just before 2021.01-rc4, likely by mistake. Revert this patch to put the board back into working order. Also note that this board has no DM SPL support due to OCRAM size limitations, but that is fine, as SPL DM support is optional. [1] https://lists.denx.de/pipermail/u-boot/2020-June/417986.html Signed-off-by: Marek Vasut <marex@denx.de> Cc: Andreas Geisreiter <ageisreiter@dh-electronics.de> Cc: Jagan Teki <jagan@amarulasolutions.com> Cc: Ludwig Zenz <lzenz@dh-electronics.de> Cc: Stefano Babic <sbabic@denx.de> Cc: Tom Rini <trini@konsulko.com>
* | | | Merge https://source.denx.de/u-boot/custodians/u-boot-usbTom Rini2021-03-0313-481/+84
|\ \ \ \ | | | | | | | | | | | | | | | | | | | | - Kconfig dependency fix for USB_KEYBOARD - musb gadget fixes / enhancements
| * | | | usb: USB keyboard requires DM_KEYBOARDHeinrich Schuchardt2021-03-031-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | If CONFIG_DM_USB=y, the USB keyboard only works if CONFIG_DM_KEYBOARD=y. Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
| * | | | Nokia RX-51: Enable usbtty serial console by defaultPali Rohár2021-03-033-31/+13
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Now when usbtty serial console is fixed in U-Boot enable CONFIG_USB_TTY for Nokia RX-51 board by default. Fix also USB product id as U-Boot ignores CONFIG_USBD_PRODUCTID macro and include U-Boot string into USB product name to indicate usage of U-Boot. CONFIG_CONSOLE_MUX is already used and U-Boot console is available for all in/out devices. Therefore there is no need to have separate commands 'run sercon', 'run usbcon' and 'run vgacon', so remove them. As space for U-Boot is limited to 256kB, enable CONFIG_OPTIMIZE_INLINING and disable some other unused options so CONFIG_USB_TTY can be enabled. Nokia RX-51 does not have easily accessible UART serial console so the only option for easy debugging is to use device's keyboard+screen or this usbtty serial console over USB. Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Lukasz Majewski <lukma@denx.de> Acked-by: Pavel Machek <pavel@ucw.cz>
| * | | | Nokia RX-51: Move content of rx51.h to rx51.cPali Rohár2021-03-032-32/+16
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | After removal of MUX configuration there is no need to have extra rx51.h. Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Lukasz Majewski <lukma@denx.de> Acked-by: Pavel Machek <pavel@ucw.cz>
| * | | | Nokia RX-51: Remove function set_muxconf_regs()Pali Rohár2021-03-032-357/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This function is not used and was never called. This board contains '#define CONFIG_SKIP_LOWLEVEL_INIT' because X-Loader set everything up, including MUX configuration. Also this MUX configuration is incorrect and does not match hardware. So remove this dead, unused and broken code. This change will decrease size of U-Boot binary. Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Lukasz Majewski <lukma@denx.de> Acked-by: Pavel Machek <pavel@ucw.cz>
| * | | | arm: omap3: Compile s_init() function only when it is usedPali Rohár2021-03-031-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Function s_init() is called only from lowlevel_init(). So compile it only when function lowlevel_init() is compiled. Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Lukasz Majewski <lukma@denx.de> Acked-by: Pavel Machek <pavel@ucw.cz>
| * | | | arm: omap3: Compile lowlevel_init() function only when it is usedPali Rohár2021-03-031-1/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Function lowlevel_init() is called only from cpu_init_crit() and this function is wrapped into #if .. #endif section. So compile also lowlevel_init() function under same #if condition. Function cpy_clk_code() uses lowlevel_init symbol to get address where go_to_speed code ends. As this symbol is not available anymore when compiling with CONFIG_SKIP_LOWLEVEL_INIT, defines a new label go_to_speed_end at the place where go_to_speed code ends. Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Lukasz Majewski <lukma@denx.de> Acked-by: Pavel Machek <pavel@ucw.cz>
| * | | | usb: gadget: Use dbg_ep0() macro instead of serial_printf()Pali Rohár2021-03-031-8/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | All debug messages from ep0.c except a few are printed by dbg_ep0() macro. So for remaining few exceptions use also dbg_ep0() instead of serial_printf(). Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Lukasz Majewski <lukma@denx.de> Acked-by: Pavel Machek <pavel@ucw.cz>
| * | | | usb: musb: Ensure that we set musb dynamic FIFO buffer for every endpointPali Rohár2021-03-031-12/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | If we do not set FIFO buffer address and size for some endpoint which is in use then default programmed address 0x0 would be used which is in conflict with address of FIFO buffer for endpoint 0. Moreover address of FIFO buffer for endpoint 0 cannot be programmed, it is fixed to 0x0. Sharing address space between more endpoints cause data loss and unexpected errors. This patch is fixing transmission of characters over usbtty serial console and allows using of usbtty for debugging purposes on Nokia N900. Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Lukasz Majewski <lukma@denx.de> Acked-by: Pavel Machek <pavel@ucw.cz>
| * | | | usb: musb: Fix handling interrupts for EP0 and SET ADDRESS commmandPali Rohár2021-03-031-8/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Interrupt for EP0 is indicated in intrtx register via first bit. This bit is set for both RX and TX despite register has only TX in its name. First bit in intrrx register is reserved, not used and never set. So remove calling musb_peri_ep0() function at every iteration of udc_irq() and musb_peri_rx() and call it only from musb_peri_tx() when correct interrupt bit in initrtx it set. Address from SET ADDRESS command must be set to faddr register only after acknowledging SERV_RXPKTRDY followed by received EP0 interrupt. So prior calling musb_peri_ep0_set_address() check for EP0 interrupt instead of (incorrect) MUSB_INTR_SOF interrupt. This patch fixes issue that host (computer) cannot register U-Boot USB device and is failing with errors: usb 1-1: new full-speed USB device number 86 using xhci_hcd usb 1-1: Device not responding to setup address. usb 1-1: Device not responding to setup address. usb 1-1: device not accepting address 86, error -71 U-Boot was writing address to faddr register too early and did not wait for correct interrupt after which should update address. Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Lukasz Majewski <lukma@denx.de> Acked-by: Pavel Machek <pavel@ucw.cz>
| * | | | usb: musb: Fix receiving of bigger buffersPali Rohár2021-03-031-1/+15
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | If musb_peri_rx_ep() was called to process received HW buffer but U-Boot cannot read it yet (e.g. because U-Boot SW buffer is full) then interrupt was marked as processed also when HW buffer stayed unprocessed. U-Boot tried to process this buffer again when it received interrupt again, but it can receive it only when sender (host) sends a new data. As sender (host) is not going to send a new data until U-Boot process current data this issue caused a deadlock in case sender (host) is emitting data faster than U-Boot can process it. Reading musb intrrx register automatically clears this register and marks interrupt as processed. So to prevent marking interrupt in U-Boot as processed, adds a new variable pending_intrrx which would contain unprocessed bits of intrrx register. For a second step, every time when musb_peri_rx_ep() is called and there are waiting data to be processed (signaled by MUSB_RXCSR_RXPKTRDY) either acknowledge sender (via musb_peri_rx_ack()) that whole HW buffer was processed or set corresponding bit in pending_intrrx that HW buffer was not fully processed yet and next iteration is required after U-Boot allocates space for reading HW buffer. This patch fixes receiving large usb buffers, e.g. file transfer via Kermit protocol implemented by 'loadb' U-Boot command over usbtty serial console. Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Lukasz Majewski <lukma@denx.de> Acked-by: Pavel Machek <pavel@ucw.cz>
| * | | | usb: musb: Fix transmission of bigger buffersPali Rohár2021-03-031-11/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | If udc_endpoint_write() was called with bigger payload which does not fit into one USB packet it is needed to transmit payload in more USB packets. First packet is transmitted by udc_endpoint_write() call itself and other packets are put into waiting queue. Implement function musb_peri_tx() which checks if endpoints are ready for transmit and continue transmission of waiting queue. This patch fixes sending big output from printenv command over usbtty serial console. Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Lukasz Majewski <lukma@denx.de> Acked-by: Pavel Machek <pavel@ucw.cz>>
| * | | | usb: musb: Read value of PERI_RXCSR to 16bit variablePali Rohár2021-03-031-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | PERI_RXCSR is 16bit register so store its value into 16bit local variable. Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Lukasz Majewski <lukma@denx.de> Acked-by: Pavel Machek <pavel@ucw.cz>
| * | | | usb: musb: Fix configuring FIFO for endpointsPali Rohár2021-03-031-4/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch fixes configuring FIFOs for one-directional endpoints which have only one queue (either RX or TX, but noth both). Size of FIFO buffer is 2^(idx+3) bytes and starting address is 2^(addr+3). Moreover first 64 bytes are reserved for EP0. Without this patch if FIFO size specified by caller was zero then idx was incorrectly calculated (expr. ffs(0)-1) and size overflowed in fifosz register. This register uses has only 4 bits for FIFO size. Moreover specifying zero buffer size is not possible (with idx=0 is minimal buffer size 8 bytes). So even for one-directional endpoints we need to correctly specify both (RX and TX) FIFO buffer sizes and its addresses. This patch is fixing calculation of start address and buffer size to minimal value and ensures that it would not overlap with buffer reserved for EP0. This issue caused loose of packets on USB bus in both directions and basically usbtty was unusable. Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Lukasz Majewski <lukma@denx.de> Acked-by: Pavel Machek <pavel@ucw.cz>
| * | | | usb: musb: Always clear the data toggle bit when configuring epPali Rohár2021-03-031-4/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Without this patch clearing was done only when U-Boot was compiled with MUSB Host Controller. But clearing of data toggle bit is needed also for MUSB Device Controller otherwise Device Controller does not work correctly. Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Lukasz Majewski <lukma@denx.de> Acked-by: Pavel Machek <pavel@ucw.cz>
| * | | | usb: musb: Fix compilation of gadget codePali Rohár2021-03-031-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | musb udc code depends on usb gadget code provided by CONFIG_USB_DEVICE as defined in drivers/usb/gadget/Makefile. But this Makefile is not included into U-Boot build when CONFIG_USB_GADGET is not set. As CONFIG_USB_DEVICE cannot be enabled together with CONFIG_USB_GADGET it means that dependency for musb udc code is not compiled during build. Fix it by including drivers/usb/gadget dependency also when CONFIG_USB_DEVICE is set. This patch fixes compile errors: arm-linux-gnueabi-ld.bfd: drivers/usb/musb/built-in.o: in function `musb_peri_ep0_rx': u-boot/drivers/usb/musb/musb_udc.c: undefined reference to `ep0_recv_setup' arm-linux-gnueabi-ld.bfd: drivers/usb/musb/built-in.o: in function `musb_peri_ep0_idle': u-boot/drivers/usb/musb/musb_udc.c: undefined reference to `ep0_recv_setup' arm-linux-gnueabi-ld.bfd: drivers/usb/musb/built-in.o: in function `musb_peri_ep0_zero_data_request': u-boot/drivers/usb/musb/musb_udc.c: undefined reference to `usbd_device_event_irq' arm-linux-gnueabi-ld.bfd: drivers/usb/musb/built-in.o: in function `musb_peri_ep0_idle': u-boot/drivers/usb/musb/musb_udc.c: undefined reference to `ep0_recv_setup' arm-linux-gnueabi-ld.bfd: drivers/usb/musb/built-in.o: in function `musb_peri_ep0_rx': u-boot/drivers/usb/musb/musb_udc.c: undefined reference to `usbd_rcv_complete' arm-linux-gnueabi-ld.bfd: drivers/usb/musb/built-in.o: in function `musb_peri_rx_ep': u-boot/drivers/usb/musb/musb_udc.c: undefined reference to `usbd_rcv_complete' arm-linux-gnueabi-ld.bfd: drivers/usb/musb/built-in.o: in function `udc_endpoint_write': u-boot/drivers/usb/musb/musb_udc.c: undefined reference to `usbd_tx_complete' arm-linux-gnueabi-ld.bfd: drivers/usb/musb/built-in.o: in function `udc_irq': u-boot/drivers/usb/musb/musb_udc.c: undefined reference to `usbd_device_event_irq' arm-linux-gnueabi-ld.bfd: u-boot/drivers/usb/musb/musb_udc.c: undefined reference to `usbd_device_event_irq' arm-linux-gnueabi-ld.bfd: u-boot/drivers/usb/musb/musb_udc.c: undefined reference to `usbd_device_event_irq' arm-linux-gnueabi-ld.bfd: u-boot/drivers/usb/musb/musb_udc.c: undefined reference to `usbd_device_event_irq' arm-linux-gnueabi-ld.bfd: u-boot/drivers/usb/musb/musb_udc.c: undefined reference to `usbd_device_event_irq' arm-linux-gnueabi-ld.bfd: drivers/usb/musb/built-in.o:u-boot/drivers/usb/musb/musb_udc.c: more undefined references to `usbd_device_event_irq' follow arm-linux-gnueabi-ld.bfd: drivers/usb/musb/built-in.o: in function `udc_setup_ep': u-boot/drivers/usb/musb/musb_udc.c: undefined reference to `usbd_alloc_urb' arm-linux-gnueabi-ld.bfd: drivers/usb/musb/built-in.o: in function `udc_startup_events': u-boot/drivers/usb/musb/musb_udc.c: undefined reference to `usbd_device_event_irq' arm-linux-gnueabi-ld.bfd: u-boot/drivers/usb/musb/musb_udc.c: undefined reference to `usbd_device_event_irq' arm-linux-gnueabi-ld.bfd: u-boot/drivers/usb/musb/musb_udc.c: undefined reference to `usbd_device_event_irq' make: *** [Makefile:1762: u-boot] Error 1 Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Lukasz Majewski <lukma@denx.de> Acked-by: Pavel Machek <pavel@ucw.cz>
| * | | | serial: usbtty: Send urb data in correct orderPali Rohár2021-03-031-9/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Function next_urb() selects the last urb data buffer from linked list to which next data from usbtty's puts function should be appended. But to check if TX data still exists it is needed to look at the first urb data buffer from linked list. So check for endpoint->tx_urb (first from the linked list) instead of current_urb (the last from the linked list). Successful call to udc_endpoint_write() may invalidate active urb and allocate new urb in queue which invalidates pointer returned by next_urb() function. So call next_urb() prior putting data into urb buffer and call it every time after using udc_endpoint_write() function to prevent sending data from usbtty's puts function in incorrect order. This patch fixes issue that usbtty code does not transmit data when they are waiting in the tx queue. Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Lukasz Majewski <lukma@denx.de> Acked-by: Pavel Machek <pavel@ucw.cz>
| * | | | serial: usbtty: Fix puts functionPali Rohár2021-03-031-2/+2
|/ / / / | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This function has incorrect implementation of prepending CR prior LF. Without this patch it prepended CR prior whole string which is going to be written and let LF without leading CR. Fix this issue by inserting CR at correct place to make output on usbtty serial console more readable. Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Lukasz Majewski <lukma@denx.de> Acked-by: Pavel Machek <pavel@ucw.cz>
* | | | Merge tag 'rpi-next-2021.04.2' of ↵Tom Rini2021-03-025-14/+93
|\ \ \ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | https://source.denx.de/u-boot/custodians/u-boot-raspberrypi - Disable Grub workaround for RPi2 - enable HS200 mode for iproc sdhci - add armv7 support for iproc_rng200
| * | | | configs: rpi4_32: Enable iProc RNG200Matthias Brugger2021-03-021-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Enable the RNG driver for RPi4 with 32 bit. Signed-off-by: Matthias Brugger <mbrugger@suse.com>
| * | | | rng: iproc_rng200: Enable support for RPi4 armv7Matthias Brugger2021-03-021-4/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | On the RPi4 armv7 build we have the situationt that we use physical addresses of 64 bit, while the virtual addresses are 32 bit. Remap the base address in this scenario via map_physmem(). Signed-off-by: Matthias Brugger <mbrugger@suse.com>
| * | | | MAINTAINERS: Update info for Raspberry PiMatthias Brugger2021-03-021-1/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add RPi config files and custodian repository. Signed-off-by: Matthias Brugger <mbrugger@suse.com>
| * | | | drivers: mmc: iproc_sdhci: enable HS200 modeBharat Gooty2021-03-021-9/+83
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add tuning functionality which is needed for HS200 mode. For HS200, program the correct needed 1.8 voltage Signed-off-by: Bharat Gooty <bharat.gooty@broadcom.com> Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by: Matthias Brugger <mbrugger@suse.com>
| * | | | configs: RPi2: Disable EFI Grub workaroundMatthias Brugger2021-03-021-0/+1
| | |/ / | |/| | | | | | | | | | | | | | | | | | | | | | | | | | The EFI Grub workaround isn't needed with Grub version 2.04 or higher. This version was published over a year ago, so disable the workaround to reduce boot time. Signed-off-by: Matthias Brugger <mbrugger@suse.com>
* / | | configs: Resync with savedefconfigTom Rini2021-03-028-73/+16
|/ / / | | | | | | | | | | | | | | | Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
* | | Prepare v2021.04-rc3Tom Rini2021-03-011-1/+1
| | | | | | | | | | | | Signed-off-by: Tom Rini <trini@konsulko.com>
* | | log: convert pr_*() to loggingHeinrich Schuchardt2021-03-012-38/+48
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | In drivers we use a family of printing functions including pr_err() and pr_cont(). CONFIG_LOGLEVEL is used to control which of these lead to output via printf(). Our logging functions allow finer grained control of output. So replace printf() by the matching logging functions. The usage of CONFIG_LOGLEVEL remains unchanged. Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
* | | fs: btrfs: do not fail when offset of a ROOT_ITEM is not -1Marek Behún2021-03-011-2/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | When the btrfs_read_fs_root() function is searching a ROOT_ITEM with location key offset other than -1, it currently fails via BUG_ON. The offset can have other value than -1, though. This can happen for example if a subvolume is renamed: $ btrfs subvolume create X && sync Create subvolume './X' $ btrfs inspect-internal dump-tree /dev/root | grep -B 2 'name: X$ location key (270 ROOT_ITEM 18446744073709551615) type DIR transid 283 data_len 0 name_len 1 name: X $ mv X Y && sync $ btrfs inspect-internal dump-tree /dev/root | grep -B 2 'name: Y$ location key (270 ROOT_ITEM 0) type DIR transid 285 data_len 0 name_len 1 name: Y As can be seen the offset changed from -1ULL to 0. Do not fail in this case. Signed-off-by: Marek Behún <marek.behun@nic.cz> Cc: David Sterba <dsterba@suse.com> Cc: Qu Wenruo <wqu@suse.com> Cc: Tom Rini <trini@konsulko.com>
* | | uboot-test-hooks: Switch to our GitLab instanceTom Rini2021-02-283-3/+3
| | | | | | | | | | | | | | | | | | | | | | | | As Stephen is no longer actively maintaining the uboot-test-hooks repository, switch to using the instance on our GitLab. Acked-by: Stephen Warren <swarren@wwwdotorg.org> Signed-off-by: Tom Rini <trini@konsulko.com>
* | | Correct U-Boot upstream repositoryHeinrich Schuchardt2021-02-2812-67/+67
| | | | | | | | | | | | | | | | | | | | | The U-Boot source moves to https://source.denx.de/u-boot/u-boot.git effective 2021-02-28. Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
* | | Merge tag 'efi-2021-04-rc3-2' of ↵Tom Rini2021-02-276-12/+24
|\ \ \ | |/ / |/| | | | | | | | | | | | | | | | | | | | | | | | | | https://gitlab.denx.de/u-boot/custodians/u-boot-efi Pull request for efi-2021-04-rc3-2 Bug fixes: * debug build for mkeficapsule * limit output length for VenHw, VenMedia * ACPI tables must be in EfiACPIReclaimMemory
| * | cmd/efidebug: add firmware management protocol GUIDHeinrich Schuchardt2021-02-261-0/+4
| | | | | | | | | | | | | | | | | | | | | Add missing GUID short text used in the efidebug tables and efidebug dh sub-commands. Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
generated by cgit (git 2.34.1) at 2025-10-04 01:14:18 +0000