summaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAgeFilesLines
* Merge git://git.denx.de/u-boot-marvellTom Rini2019-05-0917-3/+375
|\ | | | | | | | | | | - DM updates for multiple MVEBU boards (Stefan) - Add CRS305-1G-4S board (Luka) - Enable MMC in SPL on clearfog (Baruch)
| * arm: mvebu: clearfog: add MMC to SPL DTBaruch Siach2019-05-091-0/+4
| | | | | | | | | | | | | | | | | | This allows SPL to load the main U-Boot image from MMC once DM_MMC is enabled. Signed-off-by: Baruch Siach <baruch@tkos.co.il> Reviewed-by: Stefan Roese <sr@denx.de> Signed-off-by: Stefan Roese <sr@denx.de>
| * arm: mvebu: Add CRS305-1G-4S boardLuka Kovacic2019-05-0913-1/+364
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | CRS305-1G-4S has a switch chip with an integrated CPU (98DX3236) and like some of the other similar boards requires bin_hdr. bin_hdr (DDR3 init stage) is currently retrieved from the stock bootloader and compiled into the kwb image. Adds support for U-Boot, enable UART, SPI, Winbond SPI flash chip support and writing env to SPI flash. Signed-off-by: Luka Kovacic <me@lukakovacic.xyz> Reviewed-by: Chris Packham <judge.packham@gmail.com> Reviewed-by: Stefan Roese <sr@denx.de> Signed-off-by: Stefan Roese <sr@denx.de>
| * arm: mvebu: db-88f6820-gp: Enable BLK and DM supportStefan Roese2019-05-091-1/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch enables CONFIG_BLK and some DM enabled drivers on db-88f6820-gp to remove these compile warnings: ===================== WARNING ====================== This board does not use CONFIG_DM_MMC. Please update the board to use CONFIG_DM_MMC before the v2019.04 release. Failure to update by the deadline may result in board removal. See doc/driver-model/MIGRATION.txt for more info. ==================================================== ===================== WARNING ====================== This board does not use CONFIG_DM_USB. Please update the board to use CONFIG_DM_USB before the v2019.07 release. Failure to update by the deadline may result in board removal. See doc/driver-model/MIGRATION.txt for more info. ==================================================== ===================== WARNING ====================== This board does use CONFIG_LIBATA but has CONFIG_AHCI not enabled. Please update the storage controller driver to use CONFIG_AHCI before the v2019.07 release. Failure to update by the deadline may result in board removal. See doc/driver-model/MIGRATION.txt for more info. ==================================================== Signed-off-by: Stefan Roese <sr@denx.de> Reviewed-by: Chris Packham <judge.packham@gmail.com>
| * arm: mvebu: db-88f6720: Enable CONFIG_BLKStefan Roese2019-05-091-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | This patch enables CONFIG_BLK to remove this compile warning: ===================== WARNING ====================== This board does not use CONFIG_DM_USB. Please update the board to use CONFIG_DM_USB before the v2019.07 release. Failure to update by the deadline may result in board removal. See doc/driver-model/MIGRATION.txt for more info. ==================================================== Signed-off-by: Stefan Roese <sr@denx.de>
| * arm: mvebu: clearfog: Enable BLK and DM supportStefan Roese2019-05-091-1/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch enables CONFIG_BLK and some DM enabled drivers on clearfog to remove these compile warnings: ===================== WARNING ====================== This board does not use CONFIG_DM_MMC. Please update the board to use CONFIG_DM_MMC before the v2019.04 release. Failure to update by the deadline may result in board removal. See doc/driver-model/MIGRATION.txt for more info. ==================================================== ===================== WARNING ====================== This board does not use CONFIG_DM_USB. Please update the board to use CONFIG_DM_USB before the v2019.07 release. Failure to update by the deadline may result in board removal. See doc/driver-model/MIGRATION.txt for more info. ==================================================== ===================== WARNING ====================== This board does use CONFIG_LIBATA but has CONFIG_AHCI not enabled. Please update the storage controller driver to use CONFIG_AHCI before the v2019.07 release. Failure to update by the deadline may result in board removal. See doc/driver-model/MIGRATION.txt for more info. ==================================================== Signed-off-by: Stefan Roese <sr@denx.de>
* | Merge git://git.denx.de/u-boot-riscvTom Rini2019-05-0919-17/+180
|\ \ | | | | | | | | | | | | | | | | | | - Correct SYS_TEXT_BASE for qemu. - Support booti. - Increase SYSBOOTM_LEN for Fedora/RISCV kernel. - Support SMP booting from flash.
| * | RISCV: image: Add booti supportAtish Patra2019-05-094-3/+63
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds booti support for RISC-V Linux kernel. The existing bootm method will also continue to work as it is. It depends on the following kernel patch which adds the header to the flat Image. Gzip compressed Image (Image.gz) support is not enabled with this patch. https://patchwork.kernel.org/patch/10925543/ Tested on HiFive Unleashed and QEMU. Signed-off-by: Atish Patra <atish.patra@wdc.com> Reviewed-by: Tom Rini <trini@konsulko.com> Tested-by: Karsten Merker <merker@debian.org> Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
| * | riscv: configs: AE350 will use CONFIG_OF_SEPARATE when boots from flashRick Chen2019-05-094-7/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | When AE350 boots from flash, use CONFIG_OF_SEPARATE instead of CONFIG_OF_BOARD. Also remove unused code about prior_stage_fdt_address. And modify CONFIG_SYS_FDT_BASE as flash address. Signed-off-by: Rick Chen <rick@andestech.com> Cc: Greentime Hu <greentime@andestech.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
| * | riscv: configs: AE350 will use CONFIG_OF_PRIOR_STAGE when boots from ramRick Chen2019-05-092-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | When AE350 boots from ram, use CONFIG_OF_PRIOR_STAGE instead of CONFIG_OF_BOARD. Signed-off-by: Rick Chen <rick@andestech.com> Cc: Greentime Hu <greentime@andestech.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
| * | riscv: prior_stage_fdt_address should only be used when OF_PRIOR_STAGE is ↵Rick Chen2019-05-092-0/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | enabled This patch will fix prior_stage_fdt_address write failure problem, when AE350 boots from flash. When AE350 boots from flash, prior_stage_fdt_address will be flash address, we shall avoid it to be written. Signed-off-by: Rick Chen <rick@andestech.com> Cc: Greentime Hu <greentime@andestech.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
| * | riscv: configs: Support AE350 SMP booting from flash flowRick Chen2019-05-093-0/+77
| | | | | | | | | | | | | | | | | | | | | | | | | | | Add two defconfigs to support AE350 SMP booting from flash. Signed-off-by: Rick Chen <rick@andestech.com> Cc: Greentime Hu <greentime@andestech.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
| * | riscv: Introduce CONFIG_XIP to support booting from flashRick Chen2019-05-096-0/+21
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | When U-Boot boots from flash, during the boot process, hart_lottery and available_harts_lock variable addresses point to flash which is not writable. This causes boot failures on AE350. Introduce a config option CONFIG_XIP to support such configuration. Signed-off-by: Rick Chen <rick@andestech.com> Cc: Greentime Hu <greentime@andestech.com> Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
| * | riscv: qemu: Use correct SYS_TEXT_BASE for S-mode on 32bit systemAnup Patel2019-05-091-1/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | For 32bit system, the OpenSBI (or BBL) will jump to 0x80400000 address in S-mode whereas for 64bit system it will jump to 0x80200000 address in S-mode. Currently, the S-mode U-Boot sets SYS_TEXT_BASE to 0x80200000 for both 32bit and 64bit system. This breaks S-mode U-Boot for 32bit system. This patch sets different SYS_TEXT_BASE for 32bit and 64bit system so that S-mode U-Boot works fine for both. Signed-off-by: Anup Patel <anup.patel@wdc.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de> Tested-by: Karsten Merker <merker@debian.org>
| * | riscv: qemu-riscv.h: define CONFIG_PREBOOT (enables extlinux)David Abdurachmanov2019-05-091-0/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | - Set fdt_addr variable, which is needed for extlinux to find FDT. Otherwise booting kernel using extlinux results in missing FDT. - Also run fdt addr with FDT address so that fdt commands would work out of the box in U-Boot prompt. This is successfully used by Fedora/RISCV with 5.1-rc3+ kernel using OpenSBI -> U-Boot (S-mode) [extlinux] -> Kernel setup. Signed-off-by: David Abdurachmanov <david.abdurachmanov@gmail.com> Reviewed-by: Anup Patel <anup.patel@wdc.com> Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
| * | riscv: set CONFIG_SYS_BOOTM_LEN to SZ_64MDavid Abdurachmanov2019-05-091-6/+6
| |/ | | | | | | | | | | | | | | | | | | | | | | | | | | After updating Fedora/RISCV kernel to 5.1-rc3+ the size increased above the current threshold. Looking into HiKey, Dragonboards, etc. seems that SZ_64M is a popular option. This sucessfully boots Fedora/RISCV with 5.1-rc3+ kernel on QEMU 4.0 (master) with OpenSBI -> U-Boot (S-mode) [extlinux] -> Kernel setup. Signed-off-by: David Abdurachmanov <david.abdurachmanov@gmail.com> Reviewed-by: Anup Patel <anup.patel@wdc.com> Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
* | Merge tag 'u-boot-amlogic-20190509' of git://git.denx.de/u-boot-amlogicTom Rini2019-05-099-0/+1173
|\ \ | | | | | | | | | | | | | | | - Add USB PHY drivers for Amlogic G12A - Add USB Complex Glue driver for Amlogic G12A - Add USB Gadget support for Amlogic G12A
| * | mach-meson: g12a: add DWC2 peripheral mode supportNeil Armstrong2019-05-092-0/+138
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Adds support for Amlogic G12A USB Device mode. The DWC2 Controller behind the Glue can be connected to an OTG capable PHY. The Glue setups the PHY mode. This patch implements Device mode support by adding a board_usb_init/cleanup setting up the DWC2 controller and switch the OTG capable port to Device before starting the DWC2 controller in Device mode. Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
| * | phy: meson: add Amlogic G12A USB2 and USB3+PCIE PHY driversNeil Armstrong2019-05-094-0/+570
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This adds support for the USB PHYs found in the Amlogic G12A SoC Family. The USB2 PHY supports Host and/or Peripheral mode, depending on it's position. The first PHY is only used as Host, but the second supports Dual modes defined by the USB Control Glue HW in front of the USB Controllers. The second driver supports USB3 Host mode or PCIE 2.0 mode, depending on the layout of the board. Selection is done by the #phy-cells, making the mode static and exclusive. Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
| * | usb: dwc3: Add Meson G12A USB GlueNeil Armstrong2019-05-093-0/+465
| |/ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Adds support for Amlogic G12A USB Control Glue HW. The Amlogic G12A SoC Family embeds 2 USB Controllers : - a DWC3 IP configured as Host for USB2 and USB3 - a DWC2 IP configured as Peripheral USB2 Only A glue connects these both controllers to 2 USB2 PHYs, and optionnally to an USB3+PCIE Combo PHY shared with the PCIE controller. The Glue configures the UTMI 8bit interfaces for the USB2 PHYs, including routing of the OTG PHY between the DWC3 and DWC2 controllers, and setups the on-chip OTG mode selection for this PHY. This driver sets the OTG capable port as Host mode by default, the switch to Device mode is to be done in a separate patch. Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Reviewed-by: Marek Vasut <marex@denx.de>
* | Merge branch 'master' of git://git.denx.de/u-boot-netTom Rini2019-05-0818-183/+283
|\ \ | |/ |/| | | | | - Various PHY fixes / enhancements. - TI K2G fixes
| * net: phy: micrel: Find Micrel PHY node correctlyJames Byrne2019-05-081-1/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | In some of the device trees that specify skew values for KSZ90x1 PHYs the values are stored (incorrectly) in the MAC node, whereas in others it is in an 'ethernet-phy' subnode. Previously the code would fail to find and program these skew values, so this commit changes it to look for an "ethernet-phy" subnode first, and revert to looking in the MAC node if there isn't one. The device trees affected (where the skew values are in a subnode) are imx6qdl-icore-rqs.dtsi, r8a77970-eagle.dts, r8a77990-ebisu.dts, r8a77995-draak.dts, salvator-common.dtsi, sama5d3xcm.dtsi, sama5d3xcm_cmp.dtsi, socfpga_cyclone5_vining_fpga.dts, socfpga_stratix10_socdk.dts and ulcb.dtsi. Before this change the skew values in these device trees would be ignored. The device trees where the skew values are in the MAC node are socfpga_arria10_socdk.dtsi, socfpga_arria5_socdk.dts, socfpga_cyclone5_de0_nano_soc.dts, socfpga_cyclone5_de10_nano.dts, socfpga_cyclone5_de1_soc.dts, socfpga_cyclone5_is1.dts, socfpga_cyclone5_socdk.dts, socfpga_cyclone5_sockit.dts. These should be unaffected by this change. The changes were tested on a sama5d3xcm. Signed-off-by: James Byrne <james.byrne@origamienergy.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
| * net: phy: micrel: Use correct skew values on KSZ9021James Byrne2019-05-089-46/+79
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Commit ff7bd212cb8a ("net: phy: micrel: fix divisor value for KSZ9031 phy skew") fixed the skew value divisor for the KSZ9031, but left the code using the same divisor for the KSZ9021, which is incorrect. The preceding commit c16e69f702b1 ("net: phy: micrel: add documentation for Micrel KSZ90x1 binding") added the DTS documentation for the KSZ90x1, changing it from the equivalent file in the Linux kernel to correctly state that for this part the skew value is set in 120ps steps, whereas the Linux documentation and driver continue to this day to use the incorrect value of 200 that came from the original KSZ9021 datasheet before it was corrected in revision 1.2 (Feb 2014). This commit sorts out the resulting confusion in a consistent way by making the following changes: - Update the documentation to be clear about what the skew values mean, in the same was as for the KSZ9031. - Update the Micrel PHY driver to select the appropriate divisor for both parts. - Adjust all the device trees that state skew values for KSZ9021 PHYs to use values based on 120ps steps instead of 200ps steps. This will result in the same values being programmed into the skew registers as the equivalent device trees in the Linux kernel do, where it incorrectly uses 200ps steps (since that's where all these device trees were copied from). Signed-off-by: James Byrne <james.byrne@origamienergy.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
| * net: phy: aquantia: Set only autoneg on in register 4.c441Valentin-catalin Neacsu2019-05-081-1/+6
| | | | | | | | | | | | | | | | | | | | For AQR405 in register 4.c441 bit 15 was override with 0. This caused the phy to not negotiate at 2.5GB rate with mac. To avoid this override it needed first to know the previous value of reg 4.c441 and set only bit 3. Signed-off-by: Valentin Catalin Neacsu <valentin-catalin.neacsu@nxp.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
| * net: phy: Fix return value check phy_probeSiva Durga Prasad Paladugu2019-05-081-1/+4
| | | | | | | | | | | | | | | | | | Don't ignore return value of phy_probe() call as the probe may fail and it needs to be reported. Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
| * net: phy: Reloc next and prev pointers inside phy_driversSiva Durga Prasad Paladugu2019-05-081-0/+12
| | | | | | | | | | | | | | | | | | | | This patch relocates the pointers inside phy_drivers incase of manual reloc. Without this reloc, these points to invalid pre relocation address and hence causes exception or hang. Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
| * ARM: k2g-ice: Add pinmux support for rgmii interfaceMurali Karicheri2019-05-081-9/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | This add pinmux configuration for rgmii interface so that network driver can be supported on K2G ICE boards. The pinmux configurations for this are generated using the pinmux tool at https://dev.ti.com/pinmux/app.html#/default As this required some BUFFER_CLASS definitions, same is re-used from the linux defnitions in include/dt-bindings/pinctrl/keystone.h Signed-off-by: Murali Karicheri <m-karicheri2@ti.com> Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
| * ARM: k2g-gp-evm: update to rgmii pinmux configurationMurali Karicheri2019-05-081-9/+9
| | | | | | | | | | | | | | | | | | | | This patch updates pinmux configuration for K2G GP EVM based on data generated by the pinmux tool at https://dev.ti.com/pinmux/app.html#/default Signed-off-by: Murali Karicheri <m-karicheri2@ti.com> Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
| * drivers: net: ldpaa_eth: fix resource leakPankaj Bansal2019-05-081-0/+1
| | | | | | | | | | | | | | | | | | | | if an error occurs in ldpaa_eth_init, need to free all resources before returning the error. Threfore, free net_dev before returning from ldpaa_eth_init. Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
| * net: phy: realtek: Introduce quirk to mark RXC not stoppableCarlo Caione2019-05-072-0/+39
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | When EEE is supported by the PHY and the driver allows it, libphy in the kernel is configuring the PHY to stop receiving the xMII clock while it is signaling LPI. While this (usually) works fine in the kernel this is causing issues in U-Boot when rebooting from the linux kernel with this bit set (without having the possibility to reset the PHY) where the PHY suddenly stops working. A new quirk is introduced to unconditionally reset this bit. If the quirk is not enabled using the proper configuration symbol, the PHY state is not changed. Signed-off-by: Carlo Caione <ccaione@baylibre.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
| * cmd: mdio: Switch to generic helpers when accessing the registersCarlo Caione2019-05-071-11/+16
| | | | | | | | | | | | | | | | | | | | Switch to use the generic helpers to access the MMD registers so that we can used the same command also for C45 PHYs, C22 PHYs with direct and indirect access and PHYs implementing a custom way to access the registers. Signed-off-by: Carlo Caione <ccaione@baylibre.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
| * net: phy: ti: use generic helpers to access MMD registersCarlo Caione2019-05-071-105/+25
| | | | | | | | | | | | | | | | | | Now that generic helpers are available, use those instead of relying on ti specific functions. Signed-off-by: Carlo Caione <ccaione@baylibre.com> Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
| * net: phy: Add generic helpers to access MMD PHY registersCarlo Caione2019-05-072-0/+74
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Two new helper functions (phy_read_mmd() and phy_write_mmd()) are added to allow access to the MMD PHY registers. The MMD PHY registers can be accessed by several means: 1. Using two new MMD access function hooks in the PHY driver. These functions can be implemented when the PHY driver does not support the standard IEEE Compatible clause 45 access mechanism described in clause 22 or if the PHY uses its own non-standard access mechanism. 2. Direct access for C45 PHYs and C22 PHYs when accessing the reachable DEVADs. 3. The standard clause 45 access extensions to the MMD registers through the indirection registers (clause 22) in all the other cases. Signed-off-by: Carlo Caione <ccaione@baylibre.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
* | Merge branch 'master' of git://git.denx.de/u-boot-sunxiTom Rini2019-05-0820-59/+794
|\ \ | | | | | | | | | | | | | | | | | | | | | | | | - H6 Beelink GS1 board (Clément) - Olimex A64-Teres-I board (Jonas) - sunxi build fix for CONFIG_CMD_PXE|DHCP (Ondrej) - Change include order (Jagan) - EPHY clock changes (Jagan) - EMAC enablement on Cubietruck Plus, BPI-M3 (Chen-Yu Tsai)
| * | sunxi: Enable EMAC on the Bananapi M3Chen-Yu Tsai2019-05-091-1/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The Bananapi M3 has an RTL8211E PHY connected to the EMAC using RGMII. The PHY is powered by DCDC1 through SW @ 3.3V. The board is designed to use 3.3V with RGMII, instead of the standard reduced voltage of 2.5V we see everywhere. DLDO3, which provides the I/O voltages, is raised to match. This patch enables the EMAC and Realtek PHY drivers in the defconfig. The device tree file already has the EMAC enabled. Signed-off-by: Chen-Yu Tsai <wens@csie.org> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
| * | sunxi: Enable EMAC on the Cubietruck PlusChen-Yu Tsai2019-05-091-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The Cubietruck Plus has an RTL8211E PHY connected to the EMAC using RGMII. The PHY is powered by DLDO4 @ 3.3V, while the I/O pins are powered by DLDO3 @ 2.5V. This patch enables the EMAC and Realtek PHY drivers in the defconfig. The device tree file already has the EMAC enabled. Signed-off-by: Chen-Yu Tsai <wens@csie.org> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
| * | sun50i: a64: Add Olimex A64-Teres-I board initial supportJonas Smedegaard2019-05-095-1/+341
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Olimex A64-Teres-I board is a mainboard (the only one so far) for Olimex Teres-I DIY laptop kit. Key features: - Allwinner A64 Cortex-A53 - Mali-400MP2 GPU - AXP803 PMIC - 2GB DDR3 RAM - MicroSD Slot - 16GB eMMC Flash - eDP LCD display - HDMI - USB Host - Battery management - 5V DC power supply - Certified Open Source Hardware (OSHW) Works: - i2C - MMC/SD - PWM backlight Known broken: - Internal keyboard (seems to be because the keyboard firmware loads a bootloader first, and then disconnects bootloader and connect real keyboard). External ones connected to the USB port work fine. This patch enables support for the A64-Teres-I board to u-boot, including enabling screen backlight (lacking from Linux device-tree). Linux commit details about the sun50i-a64-teres-i.dts sync: "arm64: dts: allwinner: a64: Rename uart0_pins_a label to uart0_pb_pins" (sha1: d91ebb95b96c8840932dc3a10c9f243712555467) Cosmetic warnings regarding whitespace and placement of SPDX notice for dts file was ignored. config and .dtsi file are adapted from pinebook files. Tested-by: Jonas Smedegaard <dr@jones.dk> Signed-off-by: Jonas Smedegaard <dr@jones.dk> Signed-off-by: Icenowy Zheng <icenowy@aosc.io> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com> [jagan: move board entry in MAINTAINERS file at proper position] Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
| * | net: sun8i_emac: Add EPHY CLK and RESET supportJagan Teki2019-05-091-17/+57
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add EPHY CLK and RESET support for sun8i_emac driver to enable EPHY TX clock and EPHY reset pins via CLK and RESET framework. Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Lothar Felten <lothar.felten@gmail.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
| * | test/dm: reset: Add reset_get_by_index[_nodev] testJagan Teki2019-05-091-0/+23
| | | | | | | | | | | | | | | | | | | | | | | | | | | Add sample dm reset test for reset_get_by_index and reset_get_by_index_nodev functionality code. Cc: Stephen Warren <swarren@nvidia.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Simon Glass <sjg@chromium.org>
| * | reset: Get the RESET by index without deviceJagan Teki2019-05-092-17/+52
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Getting a RESET by index with device is not straight forward for some use-cases like handling clock operations for child node in parent driver. So we need to process the child node in parent probe via ofnode and process RESET operation for child without udevice but with ofnode. So add reset_get_by_index_nodev() and move the common code in reset_get_by_index_tail() to use for reset_get_by_index() Cc: Stephen Warren <swarren@nvidia.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Simon Glass <sjg@chromium.org>
| * | test/dm: clk: Add clk_get_by_index[_nodev] testJagan Teki2019-05-091-0/+21
| | | | | | | | | | | | | | | | | | | | | | | | | | | Add sample dm clk test for clk_get_by_index and clk_get_by_index_nodev functionality code. Cc: Stephen Warren <swarren@nvidia.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Simon Glass <sjg@chromium.org>
| * | clk: Use clk_get_by_index_tail()Jagan Teki2019-05-091-22/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | clk_get_by_index_tail() now handle common clk get by index code so use it from clk_get_by_indexed_prop(). Cc: Stephen Warren <swarren@nvidia.com> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
| * | clk: Get the CLK by index without deviceJagan Teki2019-05-092-1/+75
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Getting a CLK by index with device is not straight forward for some use-cases like handling clock operations for child node in parent driver. So we need to process the child node in parent probe via ofnode and process CLK operation for child without udevice but with ofnode. So add clk_get_by_index_nodev() and move the common code in clk_get_by_index_tail() to use for clk_get_by_index() Cc: Stephen Warren <swarren@nvidia.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Simon Glass <sjg@chromium.org>
| * | serial: sifive: Change include orderJagan Teki2019-05-091-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Like clk_get_by_index, there is requirement for clk_get_by_index_nodev. In this case to make common code functionalities for dev and nodev, clk_get_by_index is trying to get the index of clock by passing ofnode instead of actual dev like current gpio uclass does. In these scenarios with current order of include files the serial_sifive driver is unable to find CONFIG_ENV_SIZE. In file included from arch/riscv/include/asm/u-boot.h:23:0, from include/dm/of.h:10, from include/dm/ofnode.h:12, from include/clk.h:11, from drivers/serial/serial_sifive.c:6: include/environment.h:145:19: error: 'CONFIG_ENV_SIZE' undeclared here (not in a function); did you mean 'CONFIG_CMD_XIMG'? #define ENV_SIZE (CONFIG_ENV_SIZE - ENV_HEADER_SIZE) So, fix consists of changing the order of include files in serial_sifive.c to include first common.h file. Cc: Anup Patel <Anup.Patel@wdc.com> Cc: Rick Chen <rick@andestech.com> Cc: Paul Walmsley <paul.walmsley@sifive.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
| * | clk: sifive: fu540-prci: Change include orderJagan Teki2019-05-091-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Like clk_get_by_index, there is requirement for clk_get_by_index_nodev. In this case to make common code functionalities for dev and nodev, clk_get_by_index is trying to get the index of clock by passing ofnode instead of actual dev like current gpio uclass does. In these scenarios with current order of include files the fu540-prci driver is unable to find CONFIG_ENV_SIZE. In file included from arch/riscv/include/asm/u-boot.h:23:0, from include/dm/of.h:10, from include/dm/ofnode.h:12, from include/clk.h:11, from include/clk-uclass.h:13, from drivers/clk/sifive/fu540-prci.c:32: include/environment.h:145:19: error: 'CONFIG_ENV_SIZE' undeclared here (not in a function); did you mean 'CONFIG_CMD_XIMG'? #define ENV_SIZE (CONFIG_ENV_SIZE - ENV_HEADER_SIZE) So, fix consists of changing the order of include files in fu540-prci.c to include first common.h file. Cc: Anup Patel <Anup.Patel@wdc.com> Cc: Rick Chen <rick@andestech.com> Cc: Paul Walmsley <paul.walmsley@sifive.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
| * | spi: atcspi200: Change include orderJagan Teki2019-05-091-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Like clk_get_by_index, there is requirement for clk_get_by_index_nodev. In this case to make common code functionalities for dev and nodev, clk_get_by_index is trying to get the index of clock by passing ofnode instead of actual dev like current gpio uclass does. In these scenarios with current order of include files the atcspi200_spi driver is unable to find CONFIG_ENV_SIZE. In file included from arch/nds32/include/asm/u-boot.h:24, from include/dm/of.h:10, from include/dm/ofnode.h:12, from include/clk.h:11, from drivers/spi/atcspi200_spi.c:9: include/environment.h:145:19: error: 'CONFIG_ENV_SIZE' undeclared here (not in a function); did you mean 'CONFIG_CMD_XIMG'? #define ENV_SIZE (CONFIG_ENV_SIZE - ENV_HEADER_SIZE) So, fix consists of changing the order of include files in atcspi200_spi.c to include first common.h file. Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
| * | sunxi: Fix build when CONFIG_CMD_PXE or CONFIG_CMD_DHCP are disabledOndrej Jirman2019-04-181-2/+14
| | | | | | | | | | | | | | | | | | | | | | | | Fixes a compilation failure with disabled PXE or DHCP command when using sunxi platform. Signed-off-by: Ondřej Jirman <megous@megous.com> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
| * | arm: dts: h6: Add Beelink GS1 initial supportClément Péron2019-04-184-0/+206
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Beelink GS1 is an Allwinner H6 based TV box, which support: - Allwinner H6 Quad-core 64-bit ARM Cortex-A53 - GPU Mali-T720 - 2GB LPDDR3 RAM - 16GB eMMC - AXP805 PMIC - 1Gbps GMAC via RTL8211E - USB 2.0 and 3.0 Host - HDMI port - S/PDIF port - 5V/2A DC power supply - Wi-Fi/BT via Fn-Link 6222B-SRB (RTL8222BS) Linux commit details about the sun50i-h6-beelink-gs1.dts sync: "arm64: dts: allwinner: h6: Introduce Beelink GS1 board" (sha1: 089bee8dd119ba084dee6b17a2e1a53df4f30193) Signed-off-by: Clément Péron <peron.clem@gmail.com> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
* | | Merge git://git.denx.de/u-boot-x86Tom Rini2019-05-0864-982/+2063
|\ \ \ | | | | | | | | | | | | | | | | | | | | | | | | - Allow x86 boards to use TPL, SPL and U-Boot proper - Update sysreset x86 driver to utilize ACPI registers to do power off - Add a new chromebook_samus_tpl board for TPL support - Several minor changes in binman tool
| * | | x86: samus: Add a target to boot through TPLSimon Glass2019-05-085-2/+111
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add a version of samus which supports booting from TPL to SPL and then to U-Boot. This allows TPL to select from an A or B SPL to support verified boot with field upgrade. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
generated by cgit (git 2.34.1) at 2024-10-06 10:31:47 +0000