diff options
Diffstat (limited to 'include/configs/p1_twr.h')
| -rw-r--r-- | include/configs/p1_twr.h | 480 |
1 files changed, 0 insertions, 480 deletions
diff --git a/include/configs/p1_twr.h b/include/configs/p1_twr.h deleted file mode 100644 index d731f9c8fa..0000000000 --- a/include/configs/p1_twr.h +++ /dev/null @@ -1,480 +0,0 @@ -/* SPDX-License-Identifier: GPL-2.0+ */ -/* - * Copyright 2013 Freescale Semiconductor, Inc. - */ - -/* - * QorIQ P1 Tower boards configuration file - */ -#ifndef __CONFIG_H -#define __CONFIG_H - -#include <linux/stringify.h> - -#if defined(CONFIG_TWR_P1025) -#define CONFIG_BOARDNAME "TWR-P1025" -#define CONFIG_SYS_LBC_LBCR 0x00080000 /* Conversion of LBC addr */ -#define CONFIG_SYS_LBC_LCRR 0x80000002 /* LB clock ratio reg */ -#endif - -#ifdef CONFIG_SDCARD -#define CONFIG_RAMBOOT_SDCARD -#define CONFIG_SYS_RAMBOOT -#define CONFIG_RESET_VECTOR_ADDRESS 0x110bfffc -#endif - -#ifndef CONFIG_RESET_VECTOR_ADDRESS -#define CONFIG_RESET_VECTOR_ADDRESS 0xeffffffc -#endif - -#ifndef CONFIG_SYS_MONITOR_BASE -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ -#endif - -#define CONFIG_PCIE1 /* PCIE controller 1 (slot 1) */ -#define CONFIG_PCIE2 /* PCIE controller 2 (slot 2) */ -#define CONFIG_FSL_PCI_INIT /* Use common FSL init code */ -#define CONFIG_PCI_INDIRECT_BRIDGE /* indirect PCI bridge support */ -#define CONFIG_SYS_PCI_64BIT /* enable 64-bit PCI resources */ - -#define CONFIG_ENV_OVERWRITE - -#define CONFIG_SYS_SATA_MAX_DEVICE 2 -#define CONFIG_LBA48 - -#ifndef __ASSEMBLY__ -extern unsigned long get_board_sys_clk(unsigned long dummy); -#endif -#define CONFIG_SYS_CLK_FREQ get_board_sys_clk(0) /*sysclk for TWR-P1025 */ - -#define CONFIG_DDR_CLK_FREQ 66666666 - -#define CONFIG_HWCONFIG -/* - * These can be toggled for performance analysis, otherwise use default. - */ -#define CONFIG_L2_CACHE -#define CONFIG_BTB - -#define CONFIG_SYS_CCSRBAR 0xffe00000 -#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR - -/* DDR Setup */ - -#define CONFIG_SYS_SDRAM_SIZE_LAW LAW_SIZE_512M -#define CONFIG_CHIP_SELECTS_PER_CTRL 1 - -#define CONFIG_SYS_SDRAM_SIZE (1u << (CONFIG_SYS_SDRAM_SIZE_LAW - 19)) -#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 -#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE - -#define CONFIG_DIMM_SLOTS_PER_CTLR 1 - -/* Default settings for DDR3 */ -#define CONFIG_SYS_DDR_CS0_BNDS 0x0000001f -#define CONFIG_SYS_DDR_CS0_CONFIG 0x80014202 -#define CONFIG_SYS_DDR_CS0_CONFIG_2 0x00000000 -#define CONFIG_SYS_DDR_CS1_BNDS 0x00000000 -#define CONFIG_SYS_DDR_CS1_CONFIG 0x00000000 -#define CONFIG_SYS_DDR_CS1_CONFIG_2 0x00000000 - -#define CONFIG_SYS_DDR_DATA_INIT 0xdeadbeef -#define CONFIG_SYS_DDR_INIT_ADDR 0x00000000 -#define CONFIG_SYS_DDR_INIT_EXT_ADDR 0x00000000 -#define CONFIG_SYS_DDR_MODE_CONTROL 0x00000000 - -#define CONFIG_SYS_DDR_ZQ_CONTROL 0x89080600 -#define CONFIG_SYS_DDR_WRLVL_CONTROL 0x8655a608 -#define CONFIG_SYS_DDR_SR_CNTR 0x00000000 -#define CONFIG_SYS_DDR_RCW_1 0x00000000 -#define CONFIG_SYS_DDR_RCW_2 0x00000000 -#define CONFIG_SYS_DDR_CONTROL 0xc70c0000 /* Type = DDR3 */ -#define CONFIG_SYS_DDR_CONTROL_2 0x04401050 -#define CONFIG_SYS_DDR_TIMING_4 0x00220001 -#define CONFIG_SYS_DDR_TIMING_5 0x03402400 - -#define CONFIG_SYS_DDR_TIMING_3 0x00020000 -#define CONFIG_SYS_DDR_TIMING_0 0x00220004 -#define CONFIG_SYS_DDR_TIMING_1 0x5c5b6544 -#define CONFIG_SYS_DDR_TIMING_2 0x0fa880de -#define CONFIG_SYS_DDR_CLK_CTRL 0x03000000 -#define CONFIG_SYS_DDR_MODE_1 0x80461320 -#define CONFIG_SYS_DDR_MODE_2 0x00008000 -#define CONFIG_SYS_DDR_INTERVAL 0x09480000 - -/* - * Memory map - * - * 0x0000_0000 0x1fff_ffff DDR Up to 512MB cacheable - * 0x8000_0000 0xdfff_ffff PCI Express Mem 1.5G non-cacheable(PCIe * 3) - * 0xffc0_0000 0xffc3_ffff PCI IO range 256k non-cacheable - * - * Localbus - * 0xe000_0000 0xe002_0000 SSD1289 128K non-cacheable - * 0xec00_0000 0xefff_ffff FLASH Up to 64M non-cacheable - * - * 0xff90_0000 0xff97_ffff L2 SRAM Up to 512K cacheable - * 0xffd0_0000 0xffd0_3fff init ram 16K Cacheable - * 0xffe0_0000 0xffef_ffff CCSR 1M non-cacheable - */ - -/* - * Local Bus Definitions - */ -#define CONFIG_SYS_MAX_FLASH_SECT 512 /* 64M */ -#define CONFIG_SYS_FLASH_BASE 0xec000000 - -#define CONFIG_SYS_FLASH_BASE_PHYS CONFIG_SYS_FLASH_BASE - -#define CONFIG_FLASH_BR_PRELIM (BR_PHYS_ADDR((CONFIG_SYS_FLASH_BASE_PHYS)) \ - | BR_PS_16 | BR_V) - -#define CONFIG_FLASH_OR_PRELIM 0xfc0000b1 - -#define CONFIG_SYS_SSD_BASE 0xe0000000 -#define CONFIG_SYS_SSD_BASE_PHYS CONFIG_SYS_SSD_BASE -#define CONFIG_SSD_BR_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_SSD_BASE_PHYS) | \ - BR_PS_16 | BR_V) -#define CONFIG_SSD_OR_PRELIM (OR_AM_64KB | OR_GPCM_CSNT | OR_GPCM_XACS | \ - OR_GPCM_ACS_DIV2 | OR_GPCM_SCY | \ - OR_GPCM_TRLX | OR_GPCM_EHTR | OR_GPCM_EAD) - -#define CONFIG_SYS_BR2_PRELIM CONFIG_SSD_BR_PRELIM -#define CONFIG_SYS_OR2_PRELIM CONFIG_SSD_OR_PRELIM - -#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE_PHYS} -#define CONFIG_SYS_FLASH_QUIET_TEST -#define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */ - -#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ - -#undef CONFIG_SYS_FLASH_CHECKSUM -#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ -#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ - -#define CONFIG_SYS_FLASH_EMPTY_INFO - -#define CONFIG_SYS_INIT_RAM_LOCK -#define CONFIG_SYS_INIT_RAM_ADDR 0xffd00000 -/* Initial L1 address */ -#define CONFIG_SYS_INIT_RAM_ADDR_PHYS CONFIG_SYS_INIT_RAM_ADDR -#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0 -#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR_PHYS -/* Size of used area in RAM */ -#define CONFIG_SYS_INIT_RAM_SIZE 0x00004000 - -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \ - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET - -#define CONFIG_SYS_MONITOR_LEN (768 * 1024) -#define CONFIG_SYS_MALLOC_LEN (1024 * 1024)/* Reserved for malloc */ - -#define CONFIG_SYS_BR0_PRELIM CONFIG_FLASH_BR_PRELIM /* NOR Base Address */ -#define CONFIG_SYS_OR0_PRELIM CONFIG_FLASH_OR_PRELIM /* NOR Options */ - -/* Serial Port - * open - index 2 - * shorted - index 1 - */ -#undef CONFIG_SERIAL_SOFTWARE_FIFO -#define CONFIG_SYS_NS16550_SERIAL -#define CONFIG_SYS_NS16550_REG_SIZE 1 -#define CONFIG_SYS_NS16550_CLK get_bus_freq(0) - -#define CONFIG_SYS_BAUDRATE_TABLE \ - {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} - -#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500) -#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600) - -/* I2C */ -#define CONFIG_SYS_I2C -#define CONFIG_SYS_I2C_FSL /* Use FSL common I2C driver */ -#define CONFIG_SYS_FSL_I2C_SPEED 400000 /* I2C spd and slave address */ -#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F -#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 -#define CONFIG_SYS_I2C_EEPROM_ADDR 0x52 - -/* - * I2C2 EEPROM - */ -#define CONFIG_SYS_FSL_I2C2_SPEED 400000 /* I2C spd and slave address */ -#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F -#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100 - -#define CONFIG_SYS_I2C_PCA9555_ADDR 0x23 - -/* enable read and write access to EEPROM */ -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5 - -#if defined(CONFIG_PCI) -/* - * General PCI - * Memory space is mapped 1-1, but I/O space must start from 0. - */ - -/* controller 2, direct to uli, tgtid 2, Base address 9000 */ -#define CONFIG_SYS_PCIE2_NAME "TWR-ELEV PCIe SLOT" -#define CONFIG_SYS_PCIE2_MEM_VIRT 0xa0000000 -#define CONFIG_SYS_PCIE2_MEM_BUS 0xa0000000 -#define CONFIG_SYS_PCIE2_MEM_PHYS 0xa0000000 -#define CONFIG_SYS_PCIE2_MEM_SIZE 0x20000000 /* 512M */ -#define CONFIG_SYS_PCIE2_IO_VIRT 0xffc10000 -#define CONFIG_SYS_PCIE2_IO_BUS 0x00000000 -#define CONFIG_SYS_PCIE2_IO_PHYS 0xffc10000 -#define CONFIG_SYS_PCIE2_IO_SIZE 0x00010000 /* 64k */ - -/* controller 1, tgtid 1, Base address a000 */ -#define CONFIG_SYS_PCIE1_NAME "mini PCIe SLOT" -#define CONFIG_SYS_PCIE1_MEM_VIRT 0x80000000 -#define CONFIG_SYS_PCIE1_MEM_BUS 0x80000000 -#define CONFIG_SYS_PCIE1_MEM_PHYS 0x80000000 -#define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */ -#define CONFIG_SYS_PCIE1_IO_VIRT 0xffc00000 -#define CONFIG_SYS_PCIE1_IO_BUS 0x00000000 -#define CONFIG_SYS_PCIE1_IO_PHYS 0xffc00000 -#define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */ - -#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ -#endif /* CONFIG_PCI */ - -#if defined(CONFIG_TSEC_ENET) - -#define CONFIG_TSEC1 -#define CONFIG_TSEC1_NAME "eTSEC1" -#undef CONFIG_TSEC2 -#undef CONFIG_TSEC2_NAME -#define CONFIG_TSEC3 -#define CONFIG_TSEC3_NAME "eTSEC3" - -#define TSEC1_PHY_ADDR 2 -#define TSEC2_PHY_ADDR 0 -#define TSEC3_PHY_ADDR 1 - -#define TSEC1_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) -#define TSEC2_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) -#define TSEC3_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) - -#define TSEC1_PHYIDX 0 -#define TSEC2_PHYIDX 0 -#define TSEC3_PHYIDX 0 - -#define CONFIG_ETHPRIME "eTSEC1" - -#define CONFIG_HAS_ETH0 -#define CONFIG_HAS_ETH1 -#undef CONFIG_HAS_ETH2 -#endif /* CONFIG_TSEC_ENET */ - -#ifdef CONFIG_QE -/* QE microcode/firmware address */ -#define CONFIG_SYS_QE_FW_ADDR 0xefec0000 -#define CONFIG_SYS_QE_FMAN_FW_LENGTH 0x10000 -#endif /* CONFIG_QE */ - -#ifdef CONFIG_TWR_P1025 -/* - * QE UEC ethernet configuration - */ -#define CONFIG_MIIM_ADDRESS (CONFIG_SYS_CCSRBAR + 0x82120) - -#undef CONFIG_UEC_ETH -#define CONFIG_PHY_MODE_NEED_CHANGE - -#define CONFIG_UEC_ETH1 /* ETH1 */ -#define CONFIG_HAS_ETH0 - -#ifdef CONFIG_UEC_ETH1 -#define CONFIG_SYS_UEC1_UCC_NUM 0 /* UCC1 */ -#define CONFIG_SYS_UEC1_RX_CLK QE_CLK12 /* CLK12 for MII */ -#define CONFIG_SYS_UEC1_TX_CLK QE_CLK9 /* CLK9 for MII */ -#define CONFIG_SYS_UEC1_ETH_TYPE FAST_ETH -#define CONFIG_SYS_UEC1_PHY_ADDR 0x18 /* 0x18 for MII */ -#define CONFIG_SYS_UEC1_INTERFACE_TYPE PHY_INTERFACE_MODE_MII -#define CONFIG_SYS_UEC1_INTERFACE_SPEED 100 -#endif /* CONFIG_UEC_ETH1 */ - -#define CONFIG_UEC_ETH5 /* ETH5 */ -#define CONFIG_HAS_ETH1 - -#ifdef CONFIG_UEC_ETH5 -#define CONFIG_SYS_UEC5_UCC_NUM 4 /* UCC5 */ -#define CONFIG_SYS_UEC5_RX_CLK QE_CLK_NONE -#define CONFIG_SYS_UEC5_TX_CLK QE_CLK13 /* CLK 13 for RMII */ -#define CONFIG_SYS_UEC5_ETH_TYPE FAST_ETH -#define CONFIG_SYS_UEC5_PHY_ADDR 0x19 /* 0x19 for RMII */ -#define CONFIG_SYS_UEC5_INTERFACE_TYPE PHY_INTERFACE_MODE_RMII -#define CONFIG_SYS_UEC5_INTERFACE_SPEED 100 -#endif /* CONFIG_UEC_ETH5 */ -#endif /* CONFIG_TWR-P1025 */ - -/* - * Dynamic MTD Partition support with mtdparts - */ - -/* - * Environment - */ -#ifdef CONFIG_SYS_RAMBOOT -#ifdef CONFIG_RAMBOOT_SDCARD -#define CONFIG_SYS_MMC_ENV_DEV 0 -#endif -#endif - -#define CONFIG_LOADS_ECHO /* echo on for serial download */ -#define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */ - -/* - * USB - */ -#define CONFIG_HAS_FSL_DR_USB - -#if defined(CONFIG_HAS_FSL_DR_USB) -#ifdef CONFIG_USB_EHCI_HCD -#define CONFIG_EHCI_HCD_INIT_AFTER_RESET -#define CONFIG_USB_EHCI_FSL -#endif -#endif - -#ifdef CONFIG_MMC -#define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC85xx_ESDHC_ADDR -#endif - -#undef CONFIG_WATCHDOG /* watchdog disabled */ - -/* - * Miscellaneous configurable options - */ -#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ - -/* - * For booting Linux, the board info and command line data - * have to be in the first 64 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial Memory for Linux*/ -#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */ - -/* - * Environment Configuration - */ -#define CONFIG_HOSTNAME "unknown" -#define CONFIG_ROOTPATH "/opt/nfsroot" -#define CONFIG_BOOTFILE "uImage" -#define CONFIG_UBOOTPATH u-boot.bin /* U-Boot image on TFTP server */ - -/* default location for tftp and bootm */ -#define CONFIG_LOADADDR 1000000 - -#define CONFIG_EXTRA_ENV_SETTINGS \ -"netdev=eth0\0" \ -"uboot=" __stringify(CONFIG_UBOOTPATH) "\0" \ -"loadaddr=1000000\0" \ -"bootfile=uImage\0" \ -"dtbfile=twr-p1025twr.dtb\0" \ -"ramdiskfile=rootfs.ext2.gz.uboot\0" \ -"qefirmwarefile=fsl_qe_ucode_1021_10_A.bin\0" \ -"tftpflash=tftpboot $loadaddr $uboot; " \ - "protect off " __stringify(CONFIG_SYS_TEXT_BASE) " +$filesize; " \ - "erase " __stringify(CONFIG_SYS_TEXT_BASE) " +$filesize; " \ - "cp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE) " $filesize; " \ - "protect on " __stringify(CONFIG_SYS_TEXT_BASE) " +$filesize; " \ - "cmp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE) " $filesize\0" \ -"kernelflash=tftpboot $loadaddr $bootfile; " \ - "protect off 0xefa80000 +$filesize; " \ - "erase 0xefa80000 +$filesize; " \ - "cp.b $loadaddr 0xefa80000 $filesize; " \ - "protect on 0xefa80000 +$filesize; " \ - "cmp.b $loadaddr 0xefa80000 $filesize\0" \ -"dtbflash=tftpboot $loadaddr $dtbfile; " \ - "protect off 0xefe80000 +$filesize; " \ - "erase 0xefe80000 +$filesize; " \ - "cp.b $loadaddr 0xefe80000 $filesize; " \ - "protect on 0xefe80000 +$filesize; " \ - "cmp.b $loadaddr 0xefe80000 $filesize\0" \ -"ramdiskflash=tftpboot $loadaddr $ramdiskfile; " \ - "protect off 0xeeb80000 +$filesize; " \ - "erase 0xeeb80000 +$filesize; " \ - "cp.b $loadaddr 0xeeb80000 $filesize; " \ - "protect on 0xeeb80000 +$filesize; " \ - "cmp.b $loadaddr 0xeeb80000 $filesize\0" \ -"qefirmwareflash=tftpboot $loadaddr $qefirmwarefile; " \ - "protect off 0xefec0000 +$filesize; " \ - "erase 0xefec0000 +$filesize; " \ - "cp.b $loadaddr 0xefec0000 $filesize; " \ - "protect on 0xefec0000 +$filesize; " \ - "cmp.b $loadaddr 0xefec0000 $filesize\0" \ -"consoledev=ttyS0\0" \ -"ramdiskaddr=2000000\0" \ -"ramdiskfile=rootfs.ext2.gz.uboot\0" \ -"fdtaddr=1e00000\0" \ -"bdev=sda1\0" \ -"norbootaddr=ef080000\0" \ -"norfdtaddr=ef040000\0" \ -"ramdisk_size=120000\0" \ -"usbboot=setenv bootargs root=/dev/sda1 rw rootdelay=5 " \ -"console=$consoledev,$baudrate $othbootargs ; bootm 0xefa80000 - 0xefe80000" - -#define CONFIG_NFSBOOTCOMMAND \ -"setenv bootargs root=/dev/nfs rw " \ -"nfsroot=$serverip:$rootpath " \ -"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ -"console=$consoledev,$baudrate $othbootargs;" \ -"tftp $loadaddr $bootfile&&" \ -"tftp $fdtaddr $fdtfile&&" \ -"bootm $loadaddr - $fdtaddr" - -#define CONFIG_HDBOOT \ -"setenv bootargs root=/dev/$bdev rw rootdelay=30 " \ -"console=$consoledev,$baudrate $othbootargs;" \ -"usb start;" \ -"ext2load usb 0:1 $loadaddr /boot/$bootfile;" \ -"ext2load usb 0:1 $fdtaddr /boot/$fdtfile;" \ -"bootm $loadaddr - $fdtaddr" - -#define CONFIG_USB_FAT_BOOT \ -"setenv bootargs root=/dev/ram rw " \ -"console=$consoledev,$baudrate $othbootargs " \ -"ramdisk_size=$ramdisk_size;" \ -"usb start;" \ -"fatload usb 0:2 $loadaddr $bootfile;" \ -"fatload usb 0:2 $fdtaddr $fdtfile;" \ -"fatload usb 0:2 $ramdiskaddr $ramdiskfile;" \ -"bootm $loadaddr $ramdiskaddr $fdtaddr" - -#define CONFIG_USB_EXT2_BOOT \ -"setenv bootargs root=/dev/ram rw " \ -"console=$consoledev,$baudrate $othbootargs " \ -"ramdisk_size=$ramdisk_size;" \ -"usb start;" \ -"ext2load usb 0:4 $loadaddr $bootfile;" \ -"ext2load usb 0:4 $fdtaddr $fdtfile;" \ -"ext2load usb 0:4 $ramdiskaddr $ramdiskfile;" \ -"bootm $loadaddr $ramdiskaddr $fdtaddr" - -#define CONFIG_NORBOOT \ -"setenv bootargs root=/dev/mtdblock3 rw " \ -"console=$consoledev,$baudrate rootfstype=jffs2 $othbootargs;" \ -"bootm $norbootaddr - $norfdtaddr" - -#define CONFIG_RAMBOOTCOMMAND_TFTP \ -"setenv bootargs root=/dev/ram rw " \ -"console=$consoledev,$baudrate $othbootargs " \ -"ramdisk_size=$ramdisk_size;" \ -"tftp $ramdiskaddr $ramdiskfile;" \ -"tftp $loadaddr $bootfile;" \ -"tftp $fdtaddr $fdtfile;" \ -"bootm $loadaddr $ramdiskaddr $fdtaddr" - -#define CONFIG_RAMBOOTCOMMAND \ -"setenv bootargs root=/dev/ram rw " \ -"console=$consoledev,$baudrate $othbootargs " \ -"ramdisk_size=$ramdisk_size;" \ -"bootm 0xefa80000 0xeeb80000 0xefe80000" - -#define CONFIG_BOOTCOMMAND CONFIG_RAMBOOTCOMMAND - -#endif /* __CONFIG_H */ |