1 files changed, 0 insertions, 114 deletions
diff --git a/board/freescale/mx35pdk/README b/board/freescale/mx35pdk/README
deleted file mode 100644
index 6f6841f099..0000000000
--- a/board/freescale/mx35pdk/README
+++ /dev/null
@@ -1,114 +0,0 @@
-Overview
---------------
-
-mx35pdk (known als as mx35_3stack) is a development board by Freescale.
-It consists of three pluggable board:
-	- CPU module, with CPU, RAM, flash
-	- Personality board, with most interfaces (USB, Network,..)
-	- Debug board with JTAG header.
-
-The board is usually delivered with redboot. This howto explains how to boot
-a linux kernel and how to replace the original bootloader with U-Boot.
-
-The board is delivered with Redboot on the NAND flash. It is possible to
-switch the boot device with the switches SW1-SW2 on the Personality board,
-and with SW5-SW10 on the Debug board.
-
-Delivered Redboot script to start the kernel
----------------------------------------------------
-
-In redboot the following script is stored:
-
-fis load kernel
-exec -c "noinitrd console=ttymxc0,115200 root=/dev/mtdblock8 rw rootfstype=jffs2 ip=dhcp fec_mac=00:04:9F:00:E7:76"
-
-Kernel is taken from flash. The image is in zImage format.
-
-Booting from NET, rootfs on NFS:
------------------------------------
-
-To change the script in redboot:
-
-load -r -b 0x100000 <path_to_zImage>
-exec -c "noinitrd console=ttymxc0,115200 root=/dev/nfsroot rootfstype=nfsroot nfsroot=192.168.1.1:/opt/eldk-4.2-arm/armVFP rw ip=dhcp"
-
-If the ip address is not set, you can set it with :
-
-ip_address -l <board_ip/netmask> -h <server_ip>
-
-Linux partitions:
----------------------------
-
-As default, the board is shipped with these partition tables for NAND
-and for NOR:
-
-Creating 5 MTD partitions on "NAND 2GiB 3,3V 8-bit":
-0x00000000-0x00100000 : "nand.bootloader"
-0x00100000-0x00600000 : "nand.kernel"
-0x00600000-0x06600000 : "nand.rootfs"
-0x06600000-0x06e00000 : "nand.configure"
-0x06e00000-0x80000000 : "nand.userfs"
-
-Creating 6 MTD partitions on "mxc_nor_flash.0":
-0x00000000-0x00080000 : "Bootloader"
-0x00080000-0x00480000 : "nor.Kernel"
-0x00480000-0x02280000 : "nor.userfs"
-0x02280000-0x03e80000 : "nor.rootfs"
-0x01fe0000-0x01fe3000 : "FIS directory"
-0x01fff000-0x04000000 : "Redboot config"
-
-NAND partitions can be recognized enabling in kernel CONFIG_MTD_REDBOOT_PARTS.
-For this board, CONFIG_MTD_REDBOOT_DIRECTORY_BLOCK should be set to 2.
-
-However, the setup in redboot is not correct and does not use the whole flash.
-
-Better solution is to use the kernel parameter mtdparts.
-Here the resulting script to be defined in RedBoot with fconfig:
-
-load -r -b 0x100000 sbabic/mx35pdk/zImage.2.6.37
-exec -c "noinitrd console=ttymxc0,115200 root=/dev/nfsroot rootfstype=nfsroot nfsroot=192.168.1.1:/opt/eldk-4.2-arm/arm rw ip=dhcp mtdparts=mxc_nand:1m(boot),5m(linux),96m(root),8m(cfg),1938m(user);physmap-flash.0:512k(b),4m(k),30m(u),28m(r)"
-
-Flashing U-Boot
---------------------------------
-
-U-Boot should be stored on the NOR flash.
-
-The boot storage can be select using the switches on the personality board
-(SW1-SW2) and on the DEBUG board (SW4-SW10).
-
-If something goes wrong flashing the bootloader, it is always possible to
-recover the board booting from the other device.
-
-Saving U-Boot in the NOR flash
----------------------------------
-
-Check the partition for boot in the NOR flash. Setting the mtdparts as reported,
-the boot partition should be /dev/mtd0.
-
-Creating 6 MTD partitions on "mxc_nor_flash.0":
-0x00000000-0x00080000 : "Bootloader"
-0x00080000-0x00480000 : "nor.Kernel"
-0x00480000-0x02280000 : "nor.userfs"
-0x02280000-0x03e80000 : "nor.rootfs"
-0x01fe0000-0x01fe3000 : "FIS directory"
-0x01fff000-0x04000000 : "Redboot config"
-
-To erase the whole partition:
-$ flash_eraseall /dev/mtd0
-
-Writing U-Boot:
-dd if=u-boot.bin of=/dev/mtd0
-
-To boot from NOR, you have to select the switches as follows:
-
-Personality board
-	SW2	all off
-	SW1	all off
-
-Debug Board:
-	SW5	0
-	SW6	0
-	SW7	0
-	SW8	1
-	SW9	1
-	SW10	0