diff options
Diffstat (limited to 'arch/arm/dts/omap4.dtsi')
| -rw-r--r-- | arch/arm/dts/omap4.dtsi | 657 |
1 files changed, 657 insertions, 0 deletions
diff --git a/arch/arm/dts/omap4.dtsi b/arch/arm/dts/omap4.dtsi new file mode 100644 index 0000000000..763bdea8c8 --- /dev/null +++ b/arch/arm/dts/omap4.dtsi @@ -0,0 +1,657 @@ +// SPDX-License-Identifier: GPL-2.0-only +/* + * Copyright (C) 2011 Texas Instruments Incorporated - http://www.ti.com/ + */ + +#include <dt-bindings/bus/ti-sysc.h> +#include <dt-bindings/clock/omap4.h> +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/interrupt-controller/arm-gic.h> +#include <dt-bindings/pinctrl/omap.h> +#include <dt-bindings/clock/omap4.h> + +/ { + compatible = "ti,omap4430", "ti,omap4"; + interrupt-parent = <&wakeupgen>; + #address-cells = <1>; + #size-cells = <1>; + chosen { }; + + aliases { + i2c0 = &i2c1; + i2c1 = &i2c2; + i2c2 = &i2c3; + i2c3 = &i2c4; + serial0 = &uart1; + serial1 = &uart2; + serial2 = &uart3; + serial3 = &uart4; + }; + + cpus { + #address-cells = <1>; + #size-cells = <0>; + + cpu@0 { + compatible = "arm,cortex-a9"; + device_type = "cpu"; + next-level-cache = <&L2>; + reg = <0x0>; + + clocks = <&dpll_mpu_ck>; + clock-names = "cpu"; + + clock-latency = <300000>; /* From omap-cpufreq driver */ + }; + cpu@1 { + compatible = "arm,cortex-a9"; + device_type = "cpu"; + next-level-cache = <&L2>; + reg = <0x1>; + }; + }; + + /* + * Note that 4430 needs cross trigger interface (CTI) supported + * before we can configure the interrupts. This means sampling + * events are not supported for pmu. Note that 4460 does not use + * CTI, see also 4460.dtsi. + */ + pmu { + compatible = "arm,cortex-a9-pmu"; + ti,hwmods = "debugss"; + }; + + gic: interrupt-controller@48241000 { + compatible = "arm,cortex-a9-gic"; + interrupt-controller; + #interrupt-cells = <3>; + reg = <0x48241000 0x1000>, + <0x48240100 0x0100>; + interrupt-parent = <&gic>; + }; + + L2: l2-cache-controller@48242000 { + compatible = "arm,pl310-cache"; + reg = <0x48242000 0x1000>; + cache-unified; + cache-level = <2>; + }; + + local-timer@48240600 { + compatible = "arm,cortex-a9-twd-timer"; + clocks = <&mpu_periphclk>; + reg = <0x48240600 0x20>; + interrupts = <GIC_PPI 13 (GIC_CPU_MASK_RAW(3) | IRQ_TYPE_EDGE_RISING)>; + interrupt-parent = <&gic>; + }; + + wakeupgen: interrupt-controller@48281000 { + compatible = "ti,omap4-wugen-mpu"; + interrupt-controller; + #interrupt-cells = <3>; + reg = <0x48281000 0x1000>; + interrupt-parent = <&gic>; + }; + + /* + * The soc node represents the soc top level view. It is used for IPs + * that are not memory mapped in the MPU view or for the MPU itself. + */ + soc { + compatible = "ti,omap-infra"; + mpu { + compatible = "ti,omap4-mpu"; + ti,hwmods = "mpu"; + sram = <&ocmcram>; + }; + + dsp { + compatible = "ti,omap3-c64"; + }; + + iva { + compatible = "ti,ivahd"; + ti,hwmods = "iva"; + }; + }; + + /* + * XXX: Use a flat representation of the OMAP4 interconnect. + * The real OMAP interconnect network is quite complex. + * Since it will not bring real advantage to represent that in DT for + * the moment, just use a fake OCP bus entry to represent the whole bus + * hierarchy. + */ + ocp { + compatible = "ti,omap4-l3-noc", "simple-bus"; + #address-cells = <1>; + #size-cells = <1>; + ranges; + ti,hwmods = "l3_main_1", "l3_main_2", "l3_main_3"; + reg = <0x44000000 0x1000>, + <0x44800000 0x2000>, + <0x45000000 0x1000>; + interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>; + + l4_wkup: interconnect@4a300000 { + }; + + l4_cfg: interconnect@4a000000 { + }; + + l4_per: interconnect@48000000 { + }; + + l4_abe: interconnect@40100000 { + }; + + ocmcram: sram@40304000 { + compatible = "mmio-sram"; + reg = <0x40304000 0xa000>; /* 40k */ + }; + + gpmc: gpmc@50000000 { + compatible = "ti,omap4430-gpmc"; + reg = <0x50000000 0x1000>; + #address-cells = <2>; + #size-cells = <1>; + interrupts = <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&sdma 4>; + dma-names = "rxtx"; + gpmc,num-cs = <8>; + gpmc,num-waitpins = <4>; + ti,hwmods = "gpmc"; + ti,no-idle-on-init; + clocks = <&l3_div_ck>; + clock-names = "fck"; + interrupt-controller; + #interrupt-cells = <2>; + gpio-controller; + #gpio-cells = <2>; + }; + + target-module@52000000 { + compatible = "ti,sysc-omap4", "ti,sysc"; + ti,hwmods = "iss"; + reg = <0x52000000 0x4>, + <0x52000010 0x4>; + reg-names = "rev", "sysc"; + ti,sysc-mask = <SYSC_OMAP4_SOFTRESET>; + ti,sysc-midle = <SYSC_IDLE_FORCE>, + <SYSC_IDLE_NO>, + <SYSC_IDLE_SMART>, + <SYSC_IDLE_SMART_WKUP>; + ti,sysc-sidle = <SYSC_IDLE_FORCE>, + <SYSC_IDLE_NO>, + <SYSC_IDLE_SMART>, + <SYSC_IDLE_SMART_WKUP>; + ti,sysc-delay-us = <2>; + clocks = <&iss_clkctrl OMAP4_ISS_CLKCTRL 0>; + clock-names = "fck"; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0x52000000 0x1000000>; + + /* No child device binding, driver in staging */ + }; + + target-module@55082000 { + compatible = "ti,sysc-omap2", "ti,sysc"; + reg = <0x55082000 0x4>, + <0x55082010 0x4>, + <0x55082014 0x4>; + reg-names = "rev", "sysc", "syss"; + ti,sysc-sidle = <SYSC_IDLE_FORCE>, + <SYSC_IDLE_NO>, + <SYSC_IDLE_SMART>; + ti,sysc-mask = <(SYSC_OMAP2_CLOCKACTIVITY | + SYSC_OMAP2_SOFTRESET | + SYSC_OMAP2_AUTOIDLE)>; + clocks = <&ducati_clkctrl OMAP4_IPU_CLKCTRL 0>; + clock-names = "fck"; + resets = <&prm_core 2>; + reset-names = "rstctrl"; + ranges = <0x0 0x55082000 0x100>; + #size-cells = <1>; + #address-cells = <1>; + + mmu_ipu: mmu@0 { + compatible = "ti,omap4-iommu"; + reg = <0x0 0x100>; + interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>; + #iommu-cells = <0>; + ti,iommu-bus-err-back; + }; + }; + + target-module@4012c000 { + compatible = "ti,sysc-omap4", "ti,sysc"; + reg = <0x4012c000 0x4>, + <0x4012c010 0x4>; + reg-names = "rev", "sysc"; + ti,sysc-mask = <SYSC_OMAP4_SOFTRESET>; + ti,sysc-sidle = <SYSC_IDLE_FORCE>, + <SYSC_IDLE_NO>, + <SYSC_IDLE_SMART>, + <SYSC_IDLE_SMART_WKUP>; + clocks = <&abe_clkctrl OMAP4_SLIMBUS1_CLKCTRL 0>; + clock-names = "fck"; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0x00000000 0x4012c000 0x1000>, /* MPU */ + <0x4902c000 0x4902c000 0x1000>; /* L3 */ + + /* No child device binding or driver in mainline */ + }; + + dmm@4e000000 { + compatible = "ti,omap4-dmm"; + reg = <0x4e000000 0x800>; + interrupts = <0 113 0x4>; + ti,hwmods = "dmm"; + }; + + emif1: emif@4c000000 { + compatible = "ti,emif-4d"; + reg = <0x4c000000 0x100>; + interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>; + ti,hwmods = "emif1"; + ti,no-idle-on-init; + phy-type = <1>; + hw-caps-read-idle-ctrl; + hw-caps-ll-interface; + hw-caps-temp-alert; + }; + + emif2: emif@4d000000 { + compatible = "ti,emif-4d"; + reg = <0x4d000000 0x100>; + interrupts = <GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>; + ti,hwmods = "emif2"; + ti,no-idle-on-init; + phy-type = <1>; + hw-caps-read-idle-ctrl; + hw-caps-ll-interface; + hw-caps-temp-alert; + }; + + aes1_target: target-module@4b501000 { + compatible = "ti,sysc-omap2", "ti,sysc"; + reg = <0x4b501080 0x4>, + <0x4b501084 0x4>, + <0x4b501088 0x4>; + reg-names = "rev", "sysc", "syss"; + ti,sysc-mask = <(SYSC_OMAP2_SOFTRESET | + SYSC_OMAP2_AUTOIDLE)>; + ti,sysc-sidle = <SYSC_IDLE_FORCE>, + <SYSC_IDLE_NO>, + <SYSC_IDLE_SMART>, + <SYSC_IDLE_SMART_WKUP>; + ti,syss-mask = <1>; + /* Domains (P, C): l4per_pwrdm, l4_secure_clkdm */ + clocks = <&l4_secure_clkctrl OMAP4_AES1_CLKCTRL 0>; + clock-names = "fck"; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0x0 0x4b501000 0x1000>; + + aes1: aes@0 { + compatible = "ti,omap4-aes"; + reg = <0 0xa0>; + interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&sdma 111>, <&sdma 110>; + dma-names = "tx", "rx"; + }; + }; + + aes2_target: target-module@4b701000 { + compatible = "ti,sysc-omap2", "ti,sysc"; + reg = <0x4b701080 0x4>, + <0x4b701084 0x4>, + <0x4b701088 0x4>; + reg-names = "rev", "sysc", "syss"; + ti,sysc-mask = <(SYSC_OMAP2_SOFTRESET | + SYSC_OMAP2_AUTOIDLE)>; + ti,sysc-sidle = <SYSC_IDLE_FORCE>, + <SYSC_IDLE_NO>, + <SYSC_IDLE_SMART>, + <SYSC_IDLE_SMART_WKUP>; + ti,syss-mask = <1>; + /* Domains (P, C): l4per_pwrdm, l4_secure_clkdm */ + clocks = <&l4_secure_clkctrl OMAP4_AES2_CLKCTRL 0>; + clock-names = "fck"; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0x0 0x4b701000 0x1000>; + + aes2: aes@0 { + compatible = "ti,omap4-aes"; + reg = <0 0xa0>; + interrupts = <GIC_SPI 64 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&sdma 114>, <&sdma 113>; + dma-names = "tx", "rx"; + }; + }; + + sham_target: target-module@4b100000 { + compatible = "ti,sysc-omap3-sham", "ti,sysc"; + reg = <0x4b100100 0x4>, + <0x4b100110 0x4>, + <0x4b100114 0x4>; + reg-names = "rev", "sysc", "syss"; + ti,sysc-mask = <(SYSC_OMAP2_SOFTRESET | + SYSC_OMAP2_AUTOIDLE)>; + ti,sysc-sidle = <SYSC_IDLE_FORCE>, + <SYSC_IDLE_NO>, + <SYSC_IDLE_SMART>; + ti,syss-mask = <1>; + /* Domains (P, C): l4per_pwrdm, l4_secure_clkdm */ + clocks = <&l4_secure_clkctrl OMAP4_SHA2MD5_CLKCTRL 0>; + clock-names = "fck"; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0x0 0x4b100000 0x1000>; + + sham: sham@0 { + compatible = "ti,omap4-sham"; + reg = <0 0x300>; + interrupts = <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&sdma 119>; + dma-names = "rx"; + }; + }; + + abb_mpu: regulator-abb-mpu { + compatible = "ti,abb-v2"; + regulator-name = "abb_mpu"; + #address-cells = <0>; + #size-cells = <0>; + ti,tranxdone-status-mask = <0x80>; + clocks = <&sys_clkin_ck>; + ti,settling-time = <50>; + ti,clock-cycles = <16>; + + status = "disabled"; + }; + + abb_iva: regulator-abb-iva { + compatible = "ti,abb-v2"; + regulator-name = "abb_iva"; + #address-cells = <0>; + #size-cells = <0>; + ti,tranxdone-status-mask = <0x80000000>; + clocks = <&sys_clkin_ck>; + ti,settling-time = <50>; + ti,clock-cycles = <16>; + + status = "disabled"; + }; + + target-module@56000000 { + compatible = "ti,sysc-omap4", "ti,sysc"; + reg = <0x5600fe00 0x4>, + <0x5600fe10 0x4>; + reg-names = "rev", "sysc"; + ti,sysc-midle = <SYSC_IDLE_FORCE>, + <SYSC_IDLE_NO>, + <SYSC_IDLE_SMART>, + <SYSC_IDLE_SMART_WKUP>; + ti,sysc-sidle = <SYSC_IDLE_FORCE>, + <SYSC_IDLE_NO>, + <SYSC_IDLE_SMART>, + <SYSC_IDLE_SMART_WKUP>; + clocks = <&l3_gfx_clkctrl OMAP4_GPU_CLKCTRL 0>; + clock-names = "fck"; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0x56000000 0x2000000>; + + /* + * Closed source PowerVR driver, no child device + * binding or driver in mainline + */ + }; + + /* + * DSS is only using l3 mapping without l4 as noted in the TRM + * "10.1.3 DSS Register Manual" for omap4460. + */ + target-module@58000000 { + compatible = "ti,sysc-omap2", "ti,sysc"; + reg = <0x58000000 4>, + <0x58000014 4>; + reg-names = "rev", "syss"; + ti,syss-mask = <1>; + clocks = <&l3_dss_clkctrl OMAP4_DSS_CORE_CLKCTRL 0>, + <&l3_dss_clkctrl OMAP4_DSS_CORE_CLKCTRL 9>, + <&l3_dss_clkctrl OMAP4_DSS_CORE_CLKCTRL 10>, + <&l3_dss_clkctrl OMAP4_DSS_CORE_CLKCTRL 11>; + clock-names = "fck", "hdmi_clk", "sys_clk", "tv_clk"; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0x58000000 0x1000000>; + + dss: dss@0 { + compatible = "ti,omap4-dss"; + reg = <0 0x80>; + status = "disabled"; + clocks = <&l3_dss_clkctrl OMAP4_DSS_CORE_CLKCTRL 8>; + clock-names = "fck"; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0 0x1000000>; + + target-module@1000 { + compatible = "ti,sysc-omap2", "ti,sysc"; + reg = <0x1000 0x4>, + <0x1010 0x4>, + <0x1014 0x4>; + reg-names = "rev", "sysc", "syss"; + ti,sysc-sidle = <SYSC_IDLE_FORCE>, + <SYSC_IDLE_NO>, + <SYSC_IDLE_SMART>; + ti,sysc-midle = <SYSC_IDLE_FORCE>, + <SYSC_IDLE_NO>, + <SYSC_IDLE_SMART>; + ti,sysc-mask = <(SYSC_OMAP2_CLOCKACTIVITY | + SYSC_OMAP2_ENAWAKEUP | + SYSC_OMAP2_SOFTRESET | + SYSC_OMAP2_AUTOIDLE)>; + ti,syss-mask = <1>; + clocks = <&l3_dss_clkctrl OMAP4_DSS_CORE_CLKCTRL 8>, + <&l3_dss_clkctrl OMAP4_DSS_CORE_CLKCTRL 10>; + clock-names = "fck", "sys_clk"; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0x1000 0x1000>; + + dispc@0 { + compatible = "ti,omap4-dispc"; + reg = <0 0x1000>; + interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&l3_dss_clkctrl OMAP4_DSS_CORE_CLKCTRL 8>; + clock-names = "fck"; + }; + }; + + target-module@2000 { + compatible = "ti,sysc-omap2", "ti,sysc"; + reg = <0x2000 0x4>, + <0x2010 0x4>, + <0x2014 0x4>; + reg-names = "rev", "sysc", "syss"; + ti,sysc-sidle = <SYSC_IDLE_FORCE>, + <SYSC_IDLE_NO>, + <SYSC_IDLE_SMART>; + ti,sysc-mask = <(SYSC_OMAP2_SOFTRESET | + SYSC_OMAP2_AUTOIDLE)>; + ti,syss-mask = <1>; + clocks = <&l3_dss_clkctrl OMAP4_DSS_CORE_CLKCTRL 8>, + <&l3_dss_clkctrl OMAP4_DSS_CORE_CLKCTRL 10>; + clock-names = "fck", "sys_clk"; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0x2000 0x1000>; + + rfbi: encoder@0 { + reg = <0 0x1000>; + status = "disabled"; + clocks = <&l3_dss_clkctrl OMAP4_DSS_CORE_CLKCTRL 8>, <&l3_div_ck>; + clock-names = "fck", "ick"; + }; + }; + + target-module@3000 { + compatible = "ti,sysc-omap2", "ti,sysc"; + reg = <0x3000 0x4>; + reg-names = "rev"; + clocks = <&l3_dss_clkctrl OMAP4_DSS_CORE_CLKCTRL 10>; + clock-names = "sys_clk"; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0x3000 0x1000>; + + venc: encoder@0 { + compatible = "ti,omap4-venc"; + reg = <0 0x1000>; + status = "disabled"; + clocks = <&l3_dss_clkctrl OMAP4_DSS_CORE_CLKCTRL 11>; + clock-names = "fck"; + }; + }; + + target-module@4000 { + compatible = "ti,sysc-omap2", "ti,sysc"; + reg = <0x4000 0x4>, + <0x4010 0x4>, + <0x4014 0x4>; + reg-names = "rev", "sysc", "syss"; + ti,sysc-sidle = <SYSC_IDLE_FORCE>, + <SYSC_IDLE_NO>, + <SYSC_IDLE_SMART>; + ti,sysc-mask = <(SYSC_OMAP2_CLOCKACTIVITY | + SYSC_OMAP2_ENAWAKEUP | + SYSC_OMAP2_SOFTRESET | + SYSC_OMAP2_AUTOIDLE)>; + ti,syss-mask = <1>; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0x4000 0x1000>; + + dsi1: encoder@0 { + compatible = "ti,omap4-dsi"; + reg = <0 0x200>, + <0x200 0x40>, + <0x300 0x20>; + reg-names = "proto", "phy", "pll"; + interrupts = <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; + clocks = <&l3_dss_clkctrl OMAP4_DSS_CORE_CLKCTRL 8>, + <&l3_dss_clkctrl OMAP4_DSS_CORE_CLKCTRL 10>; + clock-names = "fck", "sys_clk"; + }; + }; + + target-module@5000 { + compatible = "ti,sysc-omap2", "ti,sysc"; + reg = <0x5000 0x4>, + <0x5010 0x4>, + <0x5014 0x4>; + reg-names = "rev", "sysc", "syss"; + ti,sysc-sidle = <SYSC_IDLE_FORCE>, + <SYSC_IDLE_NO>, + <SYSC_IDLE_SMART>; + ti,sysc-mask = <(SYSC_OMAP2_CLOCKACTIVITY | + SYSC_OMAP2_ENAWAKEUP | + SYSC_OMAP2_SOFTRESET | + SYSC_OMAP2_AUTOIDLE)>; + ti,syss-mask = <1>; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0x5000 0x1000>; + + dsi2: encoder@0 { + compatible = "ti,omap4-dsi"; + reg = <0 0x200>, + <0x200 0x40>, + <0x300 0x20>; + reg-names = "proto", "phy", "pll"; + interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; + clocks = <&l3_dss_clkctrl OMAP4_DSS_CORE_CLKCTRL 8>, + <&l3_dss_clkctrl OMAP4_DSS_CORE_CLKCTRL 10>; + clock-names = "fck", "sys_clk"; + }; + }; + + target-module@6000 { + compatible = "ti,sysc-omap4", "ti,sysc"; + reg = <0x6000 0x4>, + <0x6010 0x4>; + reg-names = "rev", "sysc"; + /* + * Has SYSC_IDLE_SMART and SYSC_IDLE_SMART_WKUP + * but HDMI audio will fail with them. + */ + ti,sysc-sidle = <SYSC_IDLE_FORCE>, + <SYSC_IDLE_NO>; + ti,sysc-mask = <(SYSC_OMAP4_SOFTRESET)>; + clocks = <&l3_dss_clkctrl OMAP4_DSS_CORE_CLKCTRL 9>, + <&l3_dss_clkctrl OMAP4_DSS_CORE_CLKCTRL 8>; + clock-names = "fck", "dss_clk"; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0x6000 0x2000>; + + hdmi: encoder@0 { + compatible = "ti,omap4-hdmi"; + reg = <0 0x200>, + <0x200 0x100>, + <0x300 0x100>, + <0x400 0x1000>; + reg-names = "wp", "pll", "phy", "core"; + interrupts = <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; + clocks = <&l3_dss_clkctrl OMAP4_DSS_CORE_CLKCTRL 9>, + <&l3_dss_clkctrl OMAP4_DSS_CORE_CLKCTRL 10>; + clock-names = "fck", "sys_clk"; + dmas = <&sdma 76>; + dma-names = "audio_tx"; + }; + }; + }; + }; + }; +}; + +#include "omap4-l4.dtsi" +#include "omap4-l4-abe.dtsi" +#include "omap44xx-clocks.dtsi" + +&prm { + prm_tesla: prm@400 { + compatible = "ti,omap4-prm-inst", "ti,omap-prm-inst"; + reg = <0x400 0x100>; + #reset-cells = <1>; + }; + + prm_core: prm@700 { + compatible = "ti,omap4-prm-inst", "ti,omap-prm-inst"; + reg = <0x700 0x100>; + #reset-cells = <1>; + }; + + prm_ivahd: prm@f00 { + compatible = "ti,omap4-prm-inst", "ti,omap-prm-inst"; + reg = <0xf00 0x100>; + #reset-cells = <1>; + }; + + prm_device: prm@1b00 { + compatible = "ti,omap4-prm-inst", "ti,omap-prm-inst"; + reg = <0x1b00 0x40>; + #reset-cells = <1>; + }; +}; |