doc: cleanup - move board READMEs into respective board directories

Also drop a few files referring to no longer / not yet supported
boards.

Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Prafulla Wadaskar <prafulla@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Kim Phillips <kim.phillips@freescale.com>
Cc: Andy Fleming <afleming@gmail.com>
Cc: Jason Jin <jason.jin@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Acked-by: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>

1 files changed, 0 insertions, 123 deletions

diff --git a/doc/README.p2041rdb b/doc/README.p2041rdb
deleted file mode 100644
index 292d0d39cf..0000000000
--- a/doc/README.p2041rdb
+++ /dev/null
@@ -1,123 +0,0 @@
-Overview
-=========
-The P2041 Processor combines four Power Architecture processor cores
-with high-performance datapath acceleration architecture(DPAA), CoreNet
-fabric infrastructure, as well as network and peripheral bus interfaces
-required for networking, telecom/datacom, wireless infrastructure, and
-military/aerospace applications.
-
-P2041RDB board is a quad core platform supporting the P2041 processor
-of QorIQ DPAA series.
-
-Boot from NOR flash
-===================
-1. Build image
-	make P2041RDB_config
-	make all
-
-2. Program image
-	=> tftp 1000000 u-boot.bin
-	=> protect off all
-	=> erase eff80000 efffffff
-	=> cp.b 1000000 eff80000 80000
-
-3. Program RCW
-	=> tftp 1000000 rcw.bin
-	=> protect off all
-	=> erase e8000000 e801ffff
-	=> cp.b 1000000 e8000000 50
-
-4. Program FMAN Firmware ucode
-	=> tftp 1000000 ucode.bin
-	=> protect off all
-	=> erase ef000000 ef0fffff
-	=> cp.b 1000000 ef000000 2000
-
-5. Change DIP-switch
-	SW1[1-5] = 10110
-	Note: 1 stands for 'on', 0 stands for 'off'
-
-Boot from SDCard
-===================
-1. Build image
-	make P2041RDB_SDCARD_config
-	make all
-
-2. Generate PBL imge
-   Use PE tool to produce a image used to be programed to
-   SDCard which contains RCW and U-Boot image.
-
-3. Program the PBL image to SDCard
-	=> tftp 1000000 pbl_sd.bin
-	=> mmcinfo
-	=> mmc write 1000000 8 441
-
-4. Program FMAN Firmware ucode
-	=> tftp 1000000 ucode.bin
-	=> mmc write 1000000 46a 10
-
-5. Change DIP-switch
-	SW1[1-5] = 01100
-	Note: 1 stands for 'on', 0 stands for 'off'
-
-Boot from SPI flash
-===================
-1. Build image
-	make P2041RDB_SPIFLASH_config
-	make all
-
-2. Generate PBL imge
-   Use PE tool to produce a image used to be programed to
-   SPI flash which contains RCW and U-Boot image.
-
-3. Program the PBL image to SPI flash
-	=> tftp 1000000 pbl_spi.bin
-	=> spi probe 0
-	=> sf erase 0 100000
-	=> sf write 1000000 0 $filesize
-
-4. Program FMAN Firmware ucode
-	=> tftp 1000000 ucode.bin
-	=> sf erase 110000 10000
-	=> sf write 1000000 110000 $filesize
-
-5. Change DIP-switch
-	SW1[1-5] = 10100
-	Note: 1 stands for 'on', 0 stands for 'off'
-
-CPLD command
-============
-The CPLD is used to control the power sequence and some serdes lane
-mux function.
-
-cpld reset			 - hard reset to default bank
-cpld reset altbank		 - reset to alternate bank
-cpld lane_mux <lane> <mux_value> - set multiplexed lane pin
-		lane 6: 0 -> slot1 (Default)
-			1 -> SGMII
-		lane a: 0 -> slot2 (Default)
-			1 -> AURORA
-		lane c: 0 -> slot2 (Default)
-			1 -> SATA0
-		lane d: 0 -> slot2 (Default)
-			1 -> SATA1
-
-Using the Device Tree Source File
-=================================
-To create the DTB (Device Tree Binary) image file, use a command
-similar to this:
-	dtc -O dtb -b 0 -p 1024 p2041rdb.dts > p2041rdb.dtb
-
-Or use the following command:
-	{linux-2.6}/make p2041rdb.dtb ARCH=powerpc
-
-then the dtb file will be generated under the following directory:
-	{linux-2.6}/arch/powerpc/boot/p2041rdb.dtb
-
-Booting Linux
-=============
-Place a linux uImage in the TFTP disk area.
-	tftp 1000000 uImage
-	tftp 2000000 rootfs.ext2.gz.uboot
-	tftp 3000000 p2041rdb.dtb
-	bootm 1000000 2000000 3000000