Add support for UC100 boardLABEL_2004_12_18_2335

1 files changed, 193 insertions, 0 deletions

diff --git a/common/cmd_pcmcia.c b/common/cmd_pcmcia.c
index 9ff0949608..1387e8989f 100644
--- a/common/cmd_pcmcia.c
+++ b/common/cmd_pcmcia.c
@@ -3091,6 +3091,199 @@ static void cfg_ports (void)
 
 
 /* -------------------------------------------------------------------- */
+/* UC100 Boards                                          		*/
+/* -------------------------------------------------------------------- */
+
+#if defined(CONFIG_UC100)
+
+#define PCMCIA_BOARD_MSG "UC100"
+
+/*
+ * Remark: don't turn off OE "__MY_PCMCIA_GCRX_CXOE" on UC100 board.
+ *         This leads to board-hangup! (sr, 8 Dez. 2004)
+ */
+
+static void cfg_ports (void);
+
+static int hardware_enable(int slot)
+{
+	volatile immap_t	*immap;
+	volatile cpm8xx_t	*cp;
+	volatile pcmconf8xx_t	*pcmp;
+	volatile sysconf8xx_t	*sysp;
+	uint reg, mask;
+
+	debug ("hardware_enable: " PCMCIA_BOARD_MSG " Slot %c\n", 'A'+slot);
+
+	udelay(10000);
+
+	immap = (immap_t *)CFG_IMMR;
+	sysp  = (sysconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_siu_conf));
+	pcmp  = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));
+	cp    = (cpm8xx_t *)(&(((immap_t *)CFG_IMMR)->im_cpm));
+
+	/* Configure Ports for TPS2211A PC-Card Power-Interface Switch */
+	cfg_ports ();
+
+	/*
+	 * Configure SIUMCR to enable PCMCIA port B
+	 * (VFLS[0:1] are not used for debugging, we connect FRZ# instead)
+	 */
+	sysp->sc_siumcr &= ~SIUMCR_DBGC11;	/* set DBGC to 00 */
+
+	/* clear interrupt state, and disable interrupts */
+	pcmp->pcmc_pscr =  PCMCIA_MASK(_slot_);
+	pcmp->pcmc_per &= ~PCMCIA_MASK(_slot_);
+
+	/*
+	 * Disable interrupts, DMA, and PCMCIA buffers
+	 * (isolate the interface) and assert RESET signal
+	 */
+	debug ("Disable PCMCIA buffers and assert RESET\n");
+	reg  = 0;
+	reg |= __MY_PCMCIA_GCRX_CXRESET;	/* active high */
+	PCMCIA_PGCRX(_slot_) = reg;
+	udelay(500);
+
+	/*
+	 * Make sure there is a card in the slot, then configure the interface.
+	 */
+	udelay(10000);
+	debug ("[%d] %s: PIPR(%p)=0x%x\n",
+		__LINE__,__FUNCTION__,
+		&(pcmp->pcmc_pipr),pcmp->pcmc_pipr);
+	if (pcmp->pcmc_pipr & (0x18000000 >> (slot << 4))) {
+		printf ("   No Card found\n");
+		return (1);
+	}
+
+	/*
+	 * Power On.
+	 */
+	mask = PCMCIA_VS1(slot) | PCMCIA_VS2(slot);
+	reg  = pcmp->pcmc_pipr;
+	debug ("PIPR: 0x%x ==> VS1=o%s, VS2=o%s\n",
+		reg,
+		(reg&PCMCIA_VS1(slot))?"n":"ff",
+		(reg&PCMCIA_VS2(slot))?"n":"ff");
+	if ((reg & mask) == mask) {
+		puts (" 5.0V card found: ");
+	} else {
+		puts (" 3.3V card found: ");
+	}
+
+	/*  switch VCC on */
+	immap->im_ioport.iop_padat |= 0x8000; /* power enable 3.3V */
+
+	udelay(10000);
+
+	debug ("Enable PCMCIA buffers and stop RESET\n");
+	reg  =  PCMCIA_PGCRX(_slot_);
+	reg &= ~__MY_PCMCIA_GCRX_CXRESET;	/* active high */
+	reg &= ~__MY_PCMCIA_GCRX_CXOE;		/* active low  */
+	PCMCIA_PGCRX(_slot_) = reg;
+
+	udelay(250000);	/* some cards need >150 ms to come up :-( */
+
+	debug ("# hardware_enable done\n");
+
+	return (0);
+}
+
+
+#if (CONFIG_COMMANDS & CFG_CMD_PCMCIA)
+static int hardware_disable(int slot)
+{
+	volatile immap_t	*immap;
+	volatile cpm8xx_t	*cp;
+	volatile pcmconf8xx_t	*pcmp;
+	u_long reg;
+
+	debug ("hardware_disable: " PCMCIA_BOARD_MSG " Slot %c\n", 'A'+slot);
+
+	immap = (immap_t *)CFG_IMMR;
+	pcmp  = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));
+
+	/* switch VCC off */
+	immap->im_ioport.iop_padat &= ~0x8000; /* power disable 3.3V */
+
+	/* Configure PCMCIA General Control Register */
+	debug ("Disable PCMCIA buffers and assert RESET\n");
+	reg  = 0;
+	reg |= __MY_PCMCIA_GCRX_CXRESET;	/* active high */
+	PCMCIA_PGCRX(_slot_) = reg;
+
+	udelay(10000);
+
+	return (0);
+}
+#endif	/* CFG_CMD_PCMCIA */
+
+
+static int voltage_set(int slot, int vcc, int vpp)
+{
+	volatile immap_t	*immap;
+	volatile pcmconf8xx_t	*pcmp;
+	u_long reg;
+
+	debug ("voltage_set: "
+		PCMCIA_BOARD_MSG
+		" Slot %c, Vcc=%d.%d, Vpp=%d.%d\n",
+		'A'+slot, vcc/10, vcc%10, vpp/10, vcc%10);
+
+	immap = (immap_t *)CFG_IMMR;
+	pcmp  = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));
+	/*
+	 * Disable PCMCIA buffers (isolate the interface)
+	 * and assert RESET signal
+	 */
+	debug ("Disable PCMCIA buffers and assert RESET\n");
+	reg  = PCMCIA_PGCRX(_slot_);
+	reg |= __MY_PCMCIA_GCRX_CXRESET;	/* active high */
+	PCMCIA_PGCRX(_slot_) = reg;
+	udelay(500);
+
+	/*
+	 * Configure Port C pins for
+	 * 5 Volts Enable and 3 Volts enable,
+	 * Turn all power pins to Hi-Z
+	 */
+	debug ("PCMCIA power OFF\n");
+	cfg_ports ();	/* Enables switch, but all in Hi-Z */
+
+	debug ("Enable PCMCIA buffers and stop RESET\n");
+	reg  =  PCMCIA_PGCRX(_slot_);
+	reg &= ~__MY_PCMCIA_GCRX_CXRESET;	/* active high */
+	reg &= ~__MY_PCMCIA_GCRX_CXOE;		/* active low  */
+	PCMCIA_PGCRX(_slot_) = reg;
+	udelay(500);
+
+	debug ("voltage_set: " PCMCIA_BOARD_MSG " Slot %c, DONE\n",
+		slot+'A');
+	return (0);
+}
+
+static void cfg_ports (void)
+{
+	volatile immap_t	*immap;
+
+	immap = (immap_t *)CFG_IMMR;
+
+	/*
+	 * Configure Port A for MAX1602 PC-Card Power-Interface Switch
+	 */
+	immap->im_ioport.iop_padat &= ~0x8000;	/* set port x output to low */
+	immap->im_ioport.iop_padir |= 0x8000;	/* enable port x as output */
+
+	debug ("Set Port A: PAR: %08x DIR: %08x DAT: %08x\n",
+	       immap->im_ioport.iop_papar, immap->im_ioport.iop_padir,
+	       immap->im_ioport.iop_padat);
+}
+
+#endif	/* UC100 */
+
+
+/* -------------------------------------------------------------------- */
 
 #endif /* CFG_CMD_PCMCIA || (CFG_CMD_IDE && CONFIG_IDE_8xx_PCCARD) */