Merge with testing-4xx_enet (Create generic 4xx Ethernet code)

61 files changed, 419 insertions, 1869 deletions

diff --git a/MAKEALL b/MAKEALL
index dcf86b0532..fb816b8796 100755
--- a/MAKEALL
+++ b/MAKEALL
@@ -65,13 +65,14 @@ LIST_4xx="	\
 	CANBT		CPCI405		CPCI4052	CPCI405AB	\
 	CPCI440		CPCIISER4	CRAYL1		csb272		\
 	csb472		DASA_SIM	DP405		DU405		\
-	ebony		ERIC		EXBITGEN	HUB405		\
-	JSE		KAREF		METROBOX	MIP405		\
-	MIP405T		ML2		ml300		ocotea		\
-	OCRTC		ORSG		PCI405		PIP405		\
-	PLU405		PMC405		PPChameleonEVB	VOH405		\
-	W7OLMC		W7OLMG		walnut		WUH405		\
-	XPEDITE1K	yellowstone	yosemite			\
+	ebony		ERIC		EXBITGEN	G2000		\
+	HUB405		JSE		KAREF		METROBOX	\
+	MIP405		MIP405T		ML2		ml300		\
+	ocotea		OCRTC		ORSG		PCI405		\
+	PIP405		PLU405		PMC405		PPChameleonEVB	\
+	sbc405		VOH405		W7OLMC		W7OLMG		\
+	walnut		WUH405		XPEDITE1K	yellowstone	\
+	yosemite        \
 "
 
 #########################################################################
diff --git a/board/amcc/bamboo/u-boot.lds b/board/amcc/bamboo/u-boot.lds
index c978dbafe0..2b5fafa8d8 100644
--- a/board/amcc/bamboo/u-boot.lds
+++ b/board/amcc/bamboo/u-boot.lds
@@ -74,7 +74,6 @@ SECTIONS
     cpu/ppc4xx/serial.o	(.text)
     cpu/ppc4xx/cpu_init.o	(.text)
     cpu/ppc4xx/speed.o	(.text)
-    cpu/ppc4xx/440gx_enet.o	(.text)
     common/dlmalloc.o	(.text)
     lib_generic/crc32.o		(.text)
     lib_ppc/extable.o	(.text)
diff --git a/board/amcc/bubinga/u-boot.lds b/board/amcc/bubinga/u-boot.lds
index b8f08eaf7e..1d7fdd0fda 100644
--- a/board/amcc/bubinga/u-boot.lds
+++ b/board/amcc/bubinga/u-boot.lds
@@ -68,7 +68,6 @@ SECTIONS
     cpu/ppc4xx/serial.o	(.text)
     cpu/ppc4xx/cpu_init.o	(.text)
     cpu/ppc4xx/speed.o	(.text)
-    cpu/ppc4xx/405gp_enet.o	(.text)
     common/dlmalloc.o	(.text)
     lib_generic/crc32.o		(.text)
     lib_ppc/extable.o	(.text)
diff --git a/board/amcc/ebony/u-boot.lds b/board/amcc/ebony/u-boot.lds
index 0ec3fad8c3..476829dea1 100644
--- a/board/amcc/ebony/u-boot.lds
+++ b/board/amcc/ebony/u-boot.lds
@@ -74,7 +74,6 @@ SECTIONS
     cpu/ppc4xx/serial.o	(.text)
     cpu/ppc4xx/cpu_init.o	(.text)
     cpu/ppc4xx/speed.o	(.text)
-    cpu/ppc4xx/405gp_enet.o	(.text)
     common/dlmalloc.o	(.text)
     lib_generic/crc32.o		(.text)
     lib_ppc/extable.o	(.text)
diff --git a/board/amcc/ocotea/ocotea.c b/board/amcc/ocotea/ocotea.c
index 5f436eaeee..50981c2367 100644
--- a/board/amcc/ocotea/ocotea.c
+++ b/board/amcc/ocotea/ocotea.c
@@ -28,7 +28,7 @@
 #include "ocotea.h"
 #include <asm/processor.h>
 #include <spd_sdram.h>
-#include <440gx_enet.h>
+#include <ppc4xx_enet.h>
 
 #define BOOT_SMALL_FLASH	32	/* 00100000 */
 #define FLASH_ONBD_N		2	/* 00000010 */
diff --git a/board/amcc/ocotea/u-boot.lds b/board/amcc/ocotea/u-boot.lds
index a9852461e1..446812bb16 100644
--- a/board/amcc/ocotea/u-boot.lds
+++ b/board/amcc/ocotea/u-boot.lds
@@ -74,7 +74,6 @@ SECTIONS
     cpu/ppc4xx/serial.o	(.text)
     cpu/ppc4xx/cpu_init.o	(.text)
     cpu/ppc4xx/speed.o	(.text)
-    cpu/ppc4xx/440gx_enet.o	(.text)
     common/dlmalloc.o	(.text)
     lib_generic/crc32.o		(.text)
     lib_ppc/extable.o	(.text)
diff --git a/board/amcc/walnut/u-boot.lds b/board/amcc/walnut/u-boot.lds
index 7107880887..5b325f63be 100644
--- a/board/amcc/walnut/u-boot.lds
+++ b/board/amcc/walnut/u-boot.lds
@@ -68,7 +68,6 @@ SECTIONS
     cpu/ppc4xx/serial.o	(.text)
     cpu/ppc4xx/cpu_init.o	(.text)
     cpu/ppc4xx/speed.o	(.text)
-    cpu/ppc4xx/405gp_enet.o	(.text)
     common/dlmalloc.o	(.text)
     lib_generic/crc32.o		(.text)
     lib_ppc/extable.o	(.text)
diff --git a/board/amcc/yellowstone/u-boot.lds b/board/amcc/yellowstone/u-boot.lds
index 769eed3ef7..5441e78064 100644
--- a/board/amcc/yellowstone/u-boot.lds
+++ b/board/amcc/yellowstone/u-boot.lds
@@ -74,7 +74,6 @@ SECTIONS
     cpu/ppc4xx/serial.o	(.text)
     cpu/ppc4xx/cpu_init.o	(.text)
     cpu/ppc4xx/speed.o	(.text)
-    cpu/ppc4xx/405gp_enet.o	(.text)
     common/dlmalloc.o	(.text)
     lib_generic/crc32.o		(.text)
     lib_ppc/extable.o	(.text)
diff --git a/board/amcc/yosemite/u-boot.lds b/board/amcc/yosemite/u-boot.lds
index 62dc988d93..00b3198ac1 100644
--- a/board/amcc/yosemite/u-boot.lds
+++ b/board/amcc/yosemite/u-boot.lds
@@ -74,7 +74,6 @@ SECTIONS
     cpu/ppc4xx/serial.o	(.text)
     cpu/ppc4xx/cpu_init.o	(.text)
     cpu/ppc4xx/speed.o	(.text)
-    cpu/ppc4xx/405gp_enet.o	(.text)
     common/dlmalloc.o	(.text)
     lib_generic/crc32.o		(.text)
     lib_ppc/extable.o	(.text)
diff --git a/board/cray/L1/u-boot.lds b/board/cray/L1/u-boot.lds
index 88c880e200..fc0879b63f 100644
--- a/board/cray/L1/u-boot.lds
+++ b/board/cray/L1/u-boot.lds
@@ -69,7 +69,7 @@ SECTIONS
     cpu/ppc4xx/serial.o	(.text)
     cpu/ppc4xx/cpu_init.o	(.text)
     cpu/ppc4xx/speed.o	(.text)
-    cpu/ppc4xx/405gp_enet.o	(.text)
+    cpu/ppc4xx/4xx_enet.o	(.text)
     common/dlmalloc.o	(.text)
     lib_generic/crc32.o		(.text)
     lib_ppc/extable.o	(.text)
diff --git a/board/csb272/csb272.c b/board/csb272/csb272.c
index fecd7e8ef3..e847879b16 100644
--- a/board/csb272/csb272.c
+++ b/board/csb272/csb272.c
@@ -25,7 +25,7 @@
 #include <asm/processor.h>
 #include <i2c.h>
 #include <miiphy.h>
-#include <405gp_enet.h>
+#include <ppc4xx_enet.h>
 
 /*
  * Configuration data for AMIS FS6377-01 Programmable 3-PLL Clock Generator
diff --git a/board/csb272/u-boot.lds b/board/csb272/u-boot.lds
index 8dbc5927a0..8571fa414c 100644
--- a/board/csb272/u-boot.lds
+++ b/board/csb272/u-boot.lds
@@ -69,7 +69,7 @@ SECTIONS
     cpu/ppc4xx/serial.o	(.text)
     cpu/ppc4xx/cpu_init.o	(.text)
     cpu/ppc4xx/speed.o	(.text)
-    cpu/ppc4xx/405gp_enet.o	(.text)
+    cpu/ppc4xx/4xx_enet.o	(.text)
     common/dlmalloc.o	(.text)
     lib_generic/crc32.o		(.text)
 
diff --git a/board/csb472/csb472.c b/board/csb472/csb472.c
index 97de0fd9af..83418dac8c 100644
--- a/board/csb472/csb472.c
+++ b/board/csb472/csb472.c
@@ -25,7 +25,7 @@
 #include <asm/processor.h>
 #include <i2c.h>
 #include <miiphy.h>
-#include <405gp_enet.h>
+#include <ppc4xx_enet.h>
 
 /*
  * board_early_init_f: do early board initialization
diff --git a/board/csb472/u-boot.lds b/board/csb472/u-boot.lds
index f3e28ae8d8..b3d40c00a4 100644
--- a/board/csb472/u-boot.lds
+++ b/board/csb472/u-boot.lds
@@ -69,7 +69,7 @@ SECTIONS
     cpu/ppc4xx/serial.o	(.text)
     cpu/ppc4xx/cpu_init.o	(.text)
     cpu/ppc4xx/speed.o	(.text)
-    cpu/ppc4xx/405gp_enet.o	(.text)
+    cpu/ppc4xx/4xx_enet.o	(.text)
     common/dlmalloc.o	(.text)
     lib_generic/crc32.o		(.text)
 
diff --git a/board/dave/PPChameleonEVB/u-boot.lds b/board/dave/PPChameleonEVB/u-boot.lds
index d6117674b1..941f8df488 100644
--- a/board/dave/PPChameleonEVB/u-boot.lds
+++ b/board/dave/PPChameleonEVB/u-boot.lds
@@ -67,7 +67,7 @@ SECTIONS
     cpu/ppc4xx/serial.o	(.text)
     cpu/ppc4xx/cpu_init.o	(.text)
     cpu/ppc4xx/speed.o	(.text)
-    cpu/ppc4xx/405gp_enet.o	(.text)
+    cpu/ppc4xx/4xx_enet.o	(.text)
     common/dlmalloc.o	(.text)
     lib_generic/crc32.o		(.text)
     lib_ppc/extable.o	(.text)
diff --git a/board/eric/u-boot.lds b/board/eric/u-boot.lds
index 10f57d8499..fd0fdcf242 100644
--- a/board/eric/u-boot.lds
+++ b/board/eric/u-boot.lds
@@ -69,7 +69,7 @@ SECTIONS
     cpu/ppc4xx/serial.o	(.text)
     cpu/ppc4xx/cpu_init.o	(.text)
     cpu/ppc4xx/speed.o	(.text)
-    cpu/ppc4xx/405gp_enet.o	(.text)
+    cpu/ppc4xx/4xx_enet.o	(.text)
     common/dlmalloc.o	(.text)
     lib_generic/crc32.o		(.text)
     lib_ppc/extable.o	(.text)
diff --git a/board/esd/apc405/u-boot.lds b/board/esd/apc405/u-boot.lds
index 311a5fe7f2..eabcdd87e1 100644
--- a/board/esd/apc405/u-boot.lds
+++ b/board/esd/apc405/u-boot.lds
@@ -67,7 +67,6 @@ SECTIONS
     cpu/ppc4xx/serial.o	(.text)
     cpu/ppc4xx/cpu_init.o	(.text)
     cpu/ppc4xx/speed.o	(.text)
-    cpu/ppc4xx/405gp_enet.o	(.text)
     common/dlmalloc.o	(.text)
     lib_generic/crc32.o		(.text)
     lib_ppc/extable.o	(.text)
diff --git a/board/esd/ar405/u-boot.lds b/board/esd/ar405/u-boot.lds
index fcba23b684..65ab788f20 100644
--- a/board/esd/ar405/u-boot.lds
+++ b/board/esd/ar405/u-boot.lds
@@ -67,7 +67,7 @@ SECTIONS
     cpu/ppc4xx/serial.o		(.text)
     cpu/ppc4xx/cpu_init.o	(.text)
     cpu/ppc4xx/speed.o		(.text)
-    cpu/ppc4xx/405gp_enet.o	(.text)
+    cpu/ppc4xx/4xx_enet.o	(.text)
     common/dlmalloc.o		(.text)
     lib_generic/crc32.o		(.text)
     lib_ppc/extable.o		(.text)
diff --git a/board/esd/ash405/u-boot.lds b/board/esd/ash405/u-boot.lds
index ba555501ed..4de10ca6bb 100644
--- a/board/esd/ash405/u-boot.lds
+++ b/board/esd/ash405/u-boot.lds
@@ -67,7 +67,6 @@ SECTIONS
     cpu/ppc4xx/serial.o	(.text)
     cpu/ppc4xx/cpu_init.o	(.text)
     cpu/ppc4xx/speed.o	(.text)
-    cpu/ppc4xx/405gp_enet.o	(.text)
     common/dlmalloc.o	(.text)
     lib_generic/crc32.o		(.text)
     lib_ppc/extable.o	(.text)
diff --git a/board/esd/canbt/u-boot.lds b/board/esd/canbt/u-boot.lds
index d739cea776..049b731c9e 100644
--- a/board/esd/canbt/u-boot.lds
+++ b/board/esd/canbt/u-boot.lds
@@ -67,7 +67,6 @@ SECTIONS
     cpu/ppc4xx/serial.o		(.text)
     cpu/ppc4xx/cpu_init.o	(.text)
     cpu/ppc4xx/speed.o		(.text)
-    cpu/ppc4xx/405gp_enet.o	(.text)
     common/dlmalloc.o		(.text)
     lib_ppc/extable.o		(.text)
     lib_ppc/board.o		(.text)
diff --git a/board/esd/cpci405/u-boot.lds b/board/esd/cpci405/u-boot.lds
index 311a5fe7f2..eabcdd87e1 100644
--- a/board/esd/cpci405/u-boot.lds
+++ b/board/esd/cpci405/u-boot.lds
@@ -67,7 +67,6 @@ SECTIONS
     cpu/ppc4xx/serial.o	(.text)
     cpu/ppc4xx/cpu_init.o	(.text)
     cpu/ppc4xx/speed.o	(.text)
-    cpu/ppc4xx/405gp_enet.o	(.text)
     common/dlmalloc.o	(.text)
     lib_generic/crc32.o		(.text)
     lib_ppc/extable.o	(.text)
diff --git a/board/esd/cpci440/u-boot.lds b/board/esd/cpci440/u-boot.lds
index 3925ad9eb6..24c35268df 100644
--- a/board/esd/cpci440/u-boot.lds
+++ b/board/esd/cpci440/u-boot.lds
@@ -76,7 +76,6 @@ SECTIONS
     cpu/ppc4xx/serial.o	(.text)
     cpu/ppc4xx/cpu_init.o	(.text)
     cpu/ppc4xx/speed.o	(.text)
-    cpu/ppc4xx/405gp_enet.o	(.text)
     common/dlmalloc.o	(.text)
     lib_generic/crc32.o		(.text)
     lib_ppc/extable.o	(.text)
diff --git a/board/esd/cpciiser4/u-boot.lds b/board/esd/cpciiser4/u-boot.lds
index 311a5fe7f2..eabcdd87e1 100644
--- a/board/esd/cpciiser4/u-boot.lds
+++ b/board/esd/cpciiser4/u-boot.lds
@@ -67,7 +67,6 @@ SECTIONS
     cpu/ppc4xx/serial.o	(.text)
     cpu/ppc4xx/cpu_init.o	(.text)
     cpu/ppc4xx/speed.o	(.text)
-    cpu/ppc4xx/405gp_enet.o	(.text)
     common/dlmalloc.o	(.text)
     lib_generic/crc32.o		(.text)
     lib_ppc/extable.o	(.text)
diff --git a/board/esd/dp405/u-boot.lds b/board/esd/dp405/u-boot.lds
index 311a5fe7f2..b66d8cadb3 100644
--- a/board/esd/dp405/u-boot.lds
+++ b/board/esd/dp405/u-boot.lds
@@ -67,7 +67,7 @@ SECTIONS
     cpu/ppc4xx/serial.o	(.text)
     cpu/ppc4xx/cpu_init.o	(.text)
     cpu/ppc4xx/speed.o	(.text)
-    cpu/ppc4xx/405gp_enet.o	(.text)
+    cpu/ppc4xx/4xx_enet.o	(.text)
     common/dlmalloc.o	(.text)
     lib_generic/crc32.o		(.text)
     lib_ppc/extable.o	(.text)
diff --git a/board/esd/du405/u-boot.lds b/board/esd/du405/u-boot.lds
index b1793a2782..2e270a0e94 100644
--- a/board/esd/du405/u-boot.lds
+++ b/board/esd/du405/u-boot.lds
@@ -67,7 +67,6 @@ SECTIONS
     cpu/ppc4xx/serial.o	(.text)
     cpu/ppc4xx/cpu_init.o	(.text)
     cpu/ppc4xx/speed.o	(.text)
-    cpu/ppc4xx/405gp_enet.o	(.text)
     common/dlmalloc.o	(.text)
     lib_generic/crc32.o		(.text)
     lib_ppc/extable.o	(.text)
diff --git a/board/esd/hh405/u-boot.lds b/board/esd/hh405/u-boot.lds
index 311a5fe7f2..eabcdd87e1 100644
--- a/board/esd/hh405/u-boot.lds
+++ b/board/esd/hh405/u-boot.lds
@@ -67,7 +67,6 @@ SECTIONS
     cpu/ppc4xx/serial.o	(.text)
     cpu/ppc4xx/cpu_init.o	(.text)
     cpu/ppc4xx/speed.o	(.text)
-    cpu/ppc4xx/405gp_enet.o	(.text)
     common/dlmalloc.o	(.text)
     lib_generic/crc32.o		(.text)
     lib_ppc/extable.o	(.text)
diff --git a/board/esd/hub405/u-boot.lds b/board/esd/hub405/u-boot.lds
index ba555501ed..e3efc7e5f9 100644
--- a/board/esd/hub405/u-boot.lds
+++ b/board/esd/hub405/u-boot.lds
@@ -67,7 +67,7 @@ SECTIONS
     cpu/ppc4xx/serial.o	(.text)
     cpu/ppc4xx/cpu_init.o	(.text)
     cpu/ppc4xx/speed.o	(.text)
-    cpu/ppc4xx/405gp_enet.o	(.text)
+    cpu/ppc4xx/4xx_enet.o	(.text)
     common/dlmalloc.o	(.text)
     lib_generic/crc32.o		(.text)
     lib_ppc/extable.o	(.text)
diff --git a/board/esd/ocrtc/u-boot.lds b/board/esd/ocrtc/u-boot.lds
index 251a4cce9a..022cbacbad 100644
--- a/board/esd/ocrtc/u-boot.lds
+++ b/board/esd/ocrtc/u-boot.lds
@@ -67,7 +67,6 @@ SECTIONS
     cpu/ppc4xx/serial.o	(.text)
     cpu/ppc4xx/cpu_init.o	(.text)
     cpu/ppc4xx/speed.o	(.text)
-    cpu/ppc4xx/405gp_enet.o	(.text)
     common/dlmalloc.o	(.text)
     lib_generic/crc32.o		(.text)
     lib_ppc/extable.o	(.text)
diff --git a/board/esd/pci405/u-boot.lds b/board/esd/pci405/u-boot.lds
index 311a5fe7f2..eabcdd87e1 100644
--- a/board/esd/pci405/u-boot.lds
+++ b/board/esd/pci405/u-boot.lds
@@ -67,7 +67,6 @@ SECTIONS
     cpu/ppc4xx/serial.o	(.text)
     cpu/ppc4xx/cpu_init.o	(.text)
     cpu/ppc4xx/speed.o	(.text)
-    cpu/ppc4xx/405gp_enet.o	(.text)
     common/dlmalloc.o	(.text)
     lib_generic/crc32.o		(.text)
     lib_ppc/extable.o	(.text)
diff --git a/board/esd/plu405/u-boot.lds b/board/esd/plu405/u-boot.lds
index 311a5fe7f2..b66d8cadb3 100644
--- a/board/esd/plu405/u-boot.lds
+++ b/board/esd/plu405/u-boot.lds
@@ -67,7 +67,7 @@ SECTIONS
     cpu/ppc4xx/serial.o	(.text)
     cpu/ppc4xx/cpu_init.o	(.text)
     cpu/ppc4xx/speed.o	(.text)
-    cpu/ppc4xx/405gp_enet.o	(.text)
+    cpu/ppc4xx/4xx_enet.o	(.text)
     common/dlmalloc.o	(.text)
     lib_generic/crc32.o		(.text)
     lib_ppc/extable.o	(.text)
diff --git a/board/esd/pmc405/u-boot.lds b/board/esd/pmc405/u-boot.lds
index bfd71dbfcb..0884f251b6 100644
--- a/board/esd/pmc405/u-boot.lds
+++ b/board/esd/pmc405/u-boot.lds
@@ -67,7 +67,6 @@ SECTIONS
     cpu/ppc4xx/serial.o	(.text)
     cpu/ppc4xx/cpu_init.o	(.text)
     cpu/ppc4xx/speed.o	(.text)
-    cpu/ppc4xx/405gp_enet.o	(.text)
     common/dlmalloc.o	(.text)
     lib_generic/crc32.o		(.text)
     lib_ppc/extable.o	(.text)
diff --git a/board/esd/voh405/u-boot.lds b/board/esd/voh405/u-boot.lds
index 311a5fe7f2..b66d8cadb3 100644
--- a/board/esd/voh405/u-boot.lds
+++ b/board/esd/voh405/u-boot.lds
@@ -67,7 +67,7 @@ SECTIONS
     cpu/ppc4xx/serial.o	(.text)
     cpu/ppc4xx/cpu_init.o	(.text)
     cpu/ppc4xx/speed.o	(.text)
-    cpu/ppc4xx/405gp_enet.o	(.text)
+    cpu/ppc4xx/4xx_enet.o	(.text)
     common/dlmalloc.o	(.text)
     lib_generic/crc32.o		(.text)
     lib_ppc/extable.o	(.text)
diff --git a/board/esd/vom405/u-boot.lds b/board/esd/vom405/u-boot.lds
index 311a5fe7f2..eabcdd87e1 100644
--- a/board/esd/vom405/u-boot.lds
+++ b/board/esd/vom405/u-boot.lds
@@ -67,7 +67,6 @@ SECTIONS
     cpu/ppc4xx/serial.o	(.text)
     cpu/ppc4xx/cpu_init.o	(.text)
     cpu/ppc4xx/speed.o	(.text)
-    cpu/ppc4xx/405gp_enet.o	(.text)
     common/dlmalloc.o	(.text)
     lib_generic/crc32.o		(.text)
     lib_ppc/extable.o	(.text)
diff --git a/board/esd/wuh405/u-boot.lds b/board/esd/wuh405/u-boot.lds
index ba555501ed..4de10ca6bb 100644
--- a/board/esd/wuh405/u-boot.lds
+++ b/board/esd/wuh405/u-boot.lds
@@ -67,7 +67,6 @@ SECTIONS
     cpu/ppc4xx/serial.o	(.text)
     cpu/ppc4xx/cpu_init.o	(.text)
     cpu/ppc4xx/speed.o	(.text)
-    cpu/ppc4xx/405gp_enet.o	(.text)
     common/dlmalloc.o	(.text)
     lib_generic/crc32.o		(.text)
     lib_ppc/extable.o	(.text)
diff --git a/board/g2000/u-boot.lds b/board/g2000/u-boot.lds
index 311a5fe7f2..b66d8cadb3 100644
--- a/board/g2000/u-boot.lds
+++ b/board/g2000/u-boot.lds
@@ -67,7 +67,7 @@ SECTIONS
     cpu/ppc4xx/serial.o	(.text)
     cpu/ppc4xx/cpu_init.o	(.text)
     cpu/ppc4xx/speed.o	(.text)
-    cpu/ppc4xx/405gp_enet.o	(.text)
+    cpu/ppc4xx/4xx_enet.o	(.text)
     common/dlmalloc.o	(.text)
     lib_generic/crc32.o		(.text)
     lib_ppc/extable.o	(.text)
diff --git a/board/ml2/u-boot.lds b/board/ml2/u-boot.lds
index 07275d3bd7..cfddd5a87a 100644
--- a/board/ml2/u-boot.lds
+++ b/board/ml2/u-boot.lds
@@ -64,7 +64,7 @@ SECTIONS
     cpu/ppc4xx/serial.o	(.text)
     cpu/ppc4xx/cpu_init.o	(.text)
     cpu/ppc4xx/speed.o	(.text)
-    cpu/ppc4xx/405gp_enet.o	(.text)
+    cpu/ppc4xx/4xx_enet.o	(.text)
     common/dlmalloc.o	(.text)
     lib_generic/crc32.o		(.text)
     lib_ppc/extable.o	(.text)
diff --git a/board/mpl/mip405/u-boot.lds b/board/mpl/mip405/u-boot.lds
index bb0f122b57..7fa312ed0b 100644
--- a/board/mpl/mip405/u-boot.lds
+++ b/board/mpl/mip405/u-boot.lds
@@ -73,7 +73,7 @@ SECTIONS
     cpu/ppc4xx/serial.o	(.text)
     cpu/ppc4xx/cpu_init.o	(.text)
     cpu/ppc4xx/speed.o	(.text)
-    cpu/ppc4xx/405gp_enet.o	(.text)
+    cpu/ppc4xx/4xx_enet.o	(.text)
     common/dlmalloc.o	(.text)
     lib_generic/crc32.o		(.text)
     lib_ppc/extable.o	(.text)
diff --git a/board/mpl/pip405/u-boot.lds b/board/mpl/pip405/u-boot.lds
index 9b83ded4d7..f766135c49 100644
--- a/board/mpl/pip405/u-boot.lds
+++ b/board/mpl/pip405/u-boot.lds
@@ -69,7 +69,6 @@ SECTIONS
     cpu/ppc4xx/serial.o	(.text)
     cpu/ppc4xx/cpu_init.o	(.text)
     cpu/ppc4xx/speed.o	(.text)
-    cpu/ppc4xx/405gp_enet.o	(.text)
     common/dlmalloc.o	(.text)
     lib_generic/crc32.o		(.text)
     lib_ppc/extable.o	(.text)
diff --git a/board/sandburst/karef/u-boot.lds b/board/sandburst/karef/u-boot.lds
index ff8658f2fc..b16d1ca5c5 100644
--- a/board/sandburst/karef/u-boot.lds
+++ b/board/sandburst/karef/u-boot.lds
@@ -75,7 +75,7 @@ SECTIONS
     cpu/ppc4xx/serial.o	(.text)
     cpu/ppc4xx/cpu_init.o	(.text)
     cpu/ppc4xx/speed.o	(.text)
-    cpu/ppc4xx/440gx_enet.o	(.text)
+    cpu/ppc4xx/4xx_enet.o	(.text)
     common/dlmalloc.o	(.text)
     lib_generic/crc32.o		(.text)
     lib_ppc/extable.o	(.text)
diff --git a/board/sandburst/karef/u-boot.lds.debug b/board/sandburst/karef/u-boot.lds.debug
index c6522b939b..83004aa85e 100644
--- a/board/sandburst/karef/u-boot.lds.debug
+++ b/board/sandburst/karef/u-boot.lds.debug
@@ -65,7 +65,7 @@ SECTIONS
     cpu/ppc4xx/serial.o	(.text)
     cpu/ppc4xx/cpu_init.o	(.text)
     cpu/ppc4xx/speed.o	(.text)
-    cpu/ppc4xx/440gx_enet.o	(.text)
+    cpu/ppc4xx/4xx_enet.o	(.text)
     common/dlmalloc.o	(.text)
     lib_generic/crc32.o		(.text)
     lib_ppc/extable.o	(.text)
diff --git a/board/sandburst/metrobox/u-boot.lds b/board/sandburst/metrobox/u-boot.lds
index 0fdb166ed5..3b230962a9 100644
--- a/board/sandburst/metrobox/u-boot.lds
+++ b/board/sandburst/metrobox/u-boot.lds
@@ -75,7 +75,7 @@ SECTIONS
     cpu/ppc4xx/serial.o	(.text)
     cpu/ppc4xx/cpu_init.o	(.text)
     cpu/ppc4xx/speed.o	(.text)
-    cpu/ppc4xx/440gx_enet.o	(.text)
+    cpu/ppc4xx/4xx_enet.o	(.text)
     common/dlmalloc.o	(.text)
     lib_generic/crc32.o		(.text)
     lib_ppc/extable.o	(.text)
diff --git a/board/sandburst/metrobox/u-boot.lds.debug b/board/sandburst/metrobox/u-boot.lds.debug
index 459a1d83af..2b42ce495e 100644
--- a/board/sandburst/metrobox/u-boot.lds.debug
+++ b/board/sandburst/metrobox/u-boot.lds.debug
@@ -65,7 +65,7 @@ SECTIONS
     cpu/ppc4xx/serial.o	(.text)
     cpu/ppc4xx/cpu_init.o	(.text)
     cpu/ppc4xx/speed.o	(.text)
-    cpu/ppc4xx/440gx_enet.o	(.text)
+    cpu/ppc4xx/4xx_enet.o	(.text)
     common/dlmalloc.o	(.text)
     lib_generic/crc32.o		(.text)
     lib_ppc/extable.o	(.text)
diff --git a/board/sbc405/u-boot.lds b/board/sbc405/u-boot.lds
index bfd71dbfcb..45f4e1a805 100644
--- a/board/sbc405/u-boot.lds
+++ b/board/sbc405/u-boot.lds
@@ -67,7 +67,7 @@ SECTIONS
     cpu/ppc4xx/serial.o	(.text)
     cpu/ppc4xx/cpu_init.o	(.text)
     cpu/ppc4xx/speed.o	(.text)
-    cpu/ppc4xx/405gp_enet.o	(.text)
+    cpu/ppc4xx/4xx_enet.o	(.text)
     common/dlmalloc.o	(.text)
     lib_generic/crc32.o		(.text)
     lib_ppc/extable.o	(.text)
diff --git a/board/xilinx/ml300/u-boot.lds b/board/xilinx/ml300/u-boot.lds
index e7b7e107b0..8f1f28ec90 100644
--- a/board/xilinx/ml300/u-boot.lds
+++ b/board/xilinx/ml300/u-boot.lds
@@ -65,7 +65,7 @@ SECTIONS
     cpu/ppc4xx/serial.o	(.text)
     cpu/ppc4xx/cpu_init.o	(.text)
     cpu/ppc4xx/speed.o	(.text)
-    cpu/ppc4xx/405gp_enet.o	(.text)
+    cpu/ppc4xx/4xx_enet.o	(.text)
     common/dlmalloc.o	(.text)
     lib_generic/crc32.o		(.text)
     lib_ppc/extable.o	(.text)
diff --git a/board/xpedite1k/u-boot.lds b/board/xpedite1k/u-boot.lds
index 3f964c8852..92466c4cb7 100644
--- a/board/xpedite1k/u-boot.lds
+++ b/board/xpedite1k/u-boot.lds
@@ -74,7 +74,6 @@ SECTIONS
     cpu/ppc4xx/serial.o	(.text)
     cpu/ppc4xx/cpu_init.o	(.text)
     cpu/ppc4xx/speed.o	(.text)
-    cpu/ppc4xx/405gp_enet.o	(.text)
     common/dlmalloc.o	(.text)
     lib_generic/crc32.o		(.text)
     lib_ppc/extable.o	(.text)
diff --git a/board/xpedite1k/u-boot.lds.debug b/board/xpedite1k/u-boot.lds.debug
index 3530c9889a..e60a94de3f 100644
--- a/board/xpedite1k/u-boot.lds.debug
+++ b/board/xpedite1k/u-boot.lds.debug
@@ -64,7 +64,6 @@ SECTIONS
     cpu/ppc4xx/serial.o	(.text)
     cpu/ppc4xx/cpu_init.o	(.text)
     cpu/ppc4xx/speed.o	(.text)
-    cpu/ppc4xx/405gp_enet.o	(.text)
     common/dlmalloc.o	(.text)
     lib_generic/crc32.o		(.text)
     lib_ppc/extable.o	(.text)
diff --git a/cpu/ppc4xx/405gp_enet.c b/cpu/ppc4xx/405gp_enet.c
deleted file mode 100644
index 968f0ced44..0000000000
--- a/cpu/ppc4xx/405gp_enet.c
+++ /dev/null
@@ -1,1062 +0,0 @@
-/*-----------------------------------------------------------------------------+
- *
- *       This source code has been made available to you by IBM on an AS-IS
- *       basis.  Anyone receiving this source is licensed under IBM
- *       copyrights to use it in any way he or she deems fit, including
- *       copying it, modifying it, compiling it, and redistributing it either
- *       with or without modifications.  No license under IBM patents or
- *       patent applications is to be implied by the copyright license.
- *
- *       Any user of this software should understand that IBM cannot provide
- *       technical support for this software and will not be responsible for
- *       any consequences resulting from the use of this software.
- *
- *       Any person who transfers this source code or any derivative work
- *       must include the IBM copyright notice, this paragraph, and the
- *       preceding two paragraphs in the transferred software.
- *
- *       COPYRIGHT   I B M   CORPORATION 1995
- *       LICENSED MATERIAL  -  PROGRAM PROPERTY OF I B M
- *-----------------------------------------------------------------------------*/
-/*-----------------------------------------------------------------------------+
- *
- *  File Name:  enetemac.c
- *
- *  Function:   Device driver for the ethernet EMAC3 macro on the 405GP.
- *
- *  Author:     Mark Wisner
- *
- *  Change Activity-
- *
- *  Date        Description of Change                                       BY
- *  ---------   ---------------------                                       ---
- *  05-May-99   Created                                                     MKW
- *  27-Jun-99   Clean up                                                    JWB
- *  16-Jul-99   Added MAL error recovery and better IP packet handling      MKW
- *  29-Jul-99   Added Full duplex support                                   MKW
- *  06-Aug-99   Changed names for Mal CR reg                                MKW
- *  23-Aug-99   Turned off SYE when running at 10Mbs                        MKW
- *  24-Aug-99   Marked descriptor empty after call_xlc                      MKW
- *  07-Sep-99   Set MAL RX buffer size reg to ENET_MAX_MTU_ALIGNED / 16     MCG
- *              to avoid chaining maximum sized packets. Push starting
- *              RX descriptor address up to the next cache line boundary.
- *  16-Jan-00   Added support for booting with IP of 0x0                    MKW
- *  15-Mar-00   Updated enetInit() to enable broadcast addresses in the
- *	        EMAC_RXM register.                                          JWB
- *  12-Mar-01   anne-sophie.harnois@nextream.fr
- *               - Variables are compatible with those already defined in
- *                include/net.h
- *              - Receive buffer descriptor ring is used to send buffers
- *                to the user
- *              - Info print about send/received/handled packet number if
- *                INFO_405_ENET is set
- *  17-Apr-01   stefan.roese@esd-electronics.com
- *              - MAL reset in "eth_halt" included
- *              - Enet speed and duplex output now in one line
- *  08-May-01   stefan.roese@esd-electronics.com
- *              - MAL error handling added (eth_init called again)
- *  13-Nov-01   stefan.roese@esd-electronics.com
- *              - Set IST bit in EMAC_M1 reg upon 100MBit or full duplex
- *  04-Jan-02   stefan.roese@esd-electronics.com
- *              - Wait for PHY auto negotiation to complete added
- *  06-Feb-02   stefan.roese@esd-electronics.com
- *              - Bug fixed in waiting for auto negotiation to complete
- *  26-Feb-02   stefan.roese@esd-electronics.com
- *              - rx and tx buffer descriptors now allocated (no fixed address
- *                used anymore)
- *  17-Jun-02   stefan.roese@esd-electronics.com
- *              - MAL error debug printf 'M' removed (rx de interrupt may
- *                occur upon many incoming packets with only 4 rx buffers).
- *  21-Nov-03   pavel.bartusek@sysgo.com
- *              - set ZMII bridge speed on 440
- *
- *-----------------------------------------------------------------------------*/
-
-#include <common.h>
-#include <asm/processor.h>
-#include <ppc4xx.h>
-#include <commproc.h>
-#include <405gp_enet.h>
-#include <405_mal.h>
-#include <miiphy.h>
-#include <net.h>
-#include <malloc.h>
-#include "vecnum.h"
-
-#if defined(CONFIG_405GP) || defined(CONFIG_405EP) || \
-  ( defined(CONFIG_440)   && !defined(CONFIG_NET_MULTI))
-
-#if !defined(CONFIG_NET_MULTI) || !defined(CONFIG_405EP)
-/* 405GP, 440 with !CONFIG_NET_MULTI. For 440 only EMAC0 is supported */
-#define EMAC_NUM_DEV        1
-#else
-/* 440EP && CONFIG_NET_MULTI */
-#define EMAC_NUM_DEV        2
-#endif
-
-#define EMAC_RESET_TIMEOUT 1000	/* 1000 ms reset timeout */
-#define PHY_AUTONEGOTIATE_TIMEOUT 4000	/* 4000 ms autonegotiate timeout */
-
-/* Ethernet Transmit and Receive Buffers */
-/* AS.HARNOIS
- * In the same way ENET_MAX_MTU and ENET_MAX_MTU_ALIGNED are set from
- * PKTSIZE and PKTSIZE_ALIGN (include/net.h)
- */
-#define ENET_MAX_MTU           PKTSIZE
-#define ENET_MAX_MTU_ALIGNED   PKTSIZE_ALIGN
-
-/* define the number of channels implemented */
-#define EMAC_RXCHL      EMAC_NUM_DEV
-#define EMAC_TXCHL      EMAC_NUM_DEV
-
-/*-----------------------------------------------------------------------------+
- * Defines for MAL/EMAC interrupt conditions as reported in the UIC (Universal
- * Interrupt Controller).
- *-----------------------------------------------------------------------------*/
-#define MAL_UIC_ERR ( UIC_MAL_SERR | UIC_MAL_TXDE  | UIC_MAL_RXDE)
-#define MAL_UIC_DEF  (UIC_MAL_RXEOB | MAL_UIC_ERR)
-#define EMAC_UIC_DEF UIC_ENET
-#define EMAC_UIC_DEF1 UIC_ENET1
-#define SEL_UIC_DEF(p) (p ? UIC_ENET1 : UIC_ENET )
-
-
-/*-----------------------------------------------------------------------------+
- * Global variables. TX and RX descriptors and buffers.
- *-----------------------------------------------------------------------------*/
-/* IER globals */
-static uint32_t mal_ier;
-
-#if !defined(CONFIG_NET_MULTI)
-struct eth_device *emac0_dev;
-#endif
-
-/*-----------------------------------------------------------------------------+
- * Prototypes and externals.
- *-----------------------------------------------------------------------------*/
-static void enet_rcv (struct eth_device *dev, unsigned long malisr);
-
-int enetInt (struct eth_device *dev);
-static void mal_err (struct eth_device *dev, unsigned long isr,
-		     unsigned long uic, unsigned long maldef,
-		     unsigned long mal_errr);
-static void emac_err (struct eth_device *dev, unsigned long isr);
-
-/*-----------------------------------------------------------------------------+
-| ppc_405x_eth_halt
-| Disable MAL channel, and EMACn
-|
-|
-+-----------------------------------------------------------------------------*/
-static void ppc_4xx_eth_halt (struct eth_device *dev)
-{
-	EMAC_405_HW_PST hw_p = dev->priv;
-	uint32_t failsafe = 10000;
-
-	mtdcr (malier, 0x00000000); /* disable mal interrupts */
-	out32 (EMAC_IER + hw_p->hw_addr, 0x00000000);	/* disable emac interrupts */
-
-	/* 1st reset MAL channel */
-	/* Note: writing a 0 to a channel has no effect */
-	mtdcr (maltxcarr, (MAL_CR_MMSR >> (hw_p->devnum * 2)));
-	mtdcr (malrxcarr, (MAL_CR_MMSR >> hw_p->devnum));
-
-	/* wait for reset */
-	while (mfdcr (malrxcasr) & (MAL_CR_MMSR >> hw_p->devnum)) {
-		udelay (1000);	/* Delay 1 MS so as not to hammer the register */
-		failsafe--;
-		if (failsafe == 0)
-			break;
-	}
-
-	/* EMAC RESET */
-	out32 (EMAC_M0 + hw_p->hw_addr, EMAC_M0_SRST);
-
-	hw_p->print_speed = 1;	/* print speed message again next time */
-
-	return;
-}
-
-static int ppc_4xx_eth_init (struct eth_device *dev, bd_t * bis)
-{
-	int i;
-	unsigned long reg;
-	unsigned long msr;
-	unsigned long speed;
-	unsigned long duplex;
-	unsigned long failsafe;
-	unsigned mode_reg;
-	unsigned short devnum;
-	unsigned short reg_short;
-
-	EMAC_405_HW_PST hw_p = dev->priv;
-	/* before doing anything, figure out if we have a MAC address */
-	/* if not, bail */
-	if (memcmp (dev->enetaddr, "\0\0\0\0\0\0", 6) == 0)
-		return -1;
-
-	msr = mfmsr ();
-	mtmsr (msr & ~(MSR_EE));	/* disable interrupts */
-
-	devnum = hw_p->devnum;
-
-#ifdef INFO_405_ENET
-	/* AS.HARNOIS
-	 * We should have :
-	 * hw_p->stats.pkts_handled <=  hw_p->stats.pkts_rx <= hw_p->stats.pkts_handled+PKTBUFSRX
-	 * In the most cases hw_p->stats.pkts_handled = hw_p->stats.pkts_rx, but it
-	 * is possible that new packets (without relationship with
-	 * current transfer) have got the time to arrived before
-	 * netloop calls eth_halt
-	 */
-	printf ("About preceeding transfer (eth%d):\n"
-		"- Sent packet number %d\n"
-		"- Received packet number %d\n"
-		"- Handled packet number %d\n",
-		hw_p->devnum,
-		hw_p->stats.pkts_tx,
-		hw_p->stats.pkts_rx, hw_p->stats.pkts_handled);
-
-	hw_p->stats.pkts_tx = 0;
-	hw_p->stats.pkts_rx = 0;
-	hw_p->stats.pkts_handled = 0;
-#endif
-
-	/* MAL RESET */
-	mtdcr (malmcr, MAL_CR_MMSR);
-	/* wait for reset */
-	while (mfdcr (malmcr) & MAL_CR_MMSR) {
-	};
-
-#if defined(CONFIG_440EP) || defined(CONFIG_440GR)
-	out32 (ZMII_FER, 0);
-	udelay(100);
-	/* set RII mode */
-	out32 (ZMII_FER, ZMII_RMII | ZMII_MDI0);
-#elif defined(CONFIG_440)
-	/* set RMII mode */
-	out32 (ZMII_FER, ZMII_RMII | ZMII_MDI0);
-#endif /* CONFIG_440 */
-
-	/* MAL Channel RESET */
-	/* 1st reset MAL channel */
-	/* Note: writing a 0 to a channel has no effect */
-	mtdcr (maltxcarr, (MAL_TXRX_CASR >> (hw_p->devnum * 2)));
-	mtdcr (malrxcarr, (MAL_TXRX_CASR >> hw_p->devnum));
-
-	/* wait for reset */
-	/* TBS:  should have udelay and failsafe here */
-	failsafe = 10000;
-	/* wait for reset */
-	while (mfdcr (malrxcasr) & (MAL_CR_MMSR >> hw_p->devnum)) {
-		udelay (1000);	/* Delay 1 MS so as not to hammer the register */
-		failsafe--;
-		if (failsafe == 0)
-			break;
-
-	}
-
-	hw_p->tx_err_index = 0;	/* Transmit Error Index for tx_err_log */
-	hw_p->rx_err_index = 0;	/* Receive Error Index for rx_err_log */
-
-	hw_p->rx_slot = 0;	/* MAL Receive Slot */
-	hw_p->rx_i_index = 0;	/* Receive Interrupt Queue Index */
-	hw_p->rx_u_index = 0;	/* Receive User Queue Index */
-
-	hw_p->tx_slot = 0;	/* MAL Transmit Slot */
-	hw_p->tx_i_index = 0;	/* Transmit Interrupt Queue Index */
-	hw_p->tx_u_index = 0;	/* Transmit User Queue Index */
-
-	__asm__ volatile ("eieio");
-
-	/* reset emac so we have access to the phy */
-
-	out32 (EMAC_M0 + hw_p->hw_addr, EMAC_M0_SRST);
-	__asm__ volatile ("eieio");
-
-	failsafe = 1000;
-	while ((in32 (EMAC_M0 + hw_p->hw_addr) & (EMAC_M0_SRST)) && failsafe) {
-		udelay (1000);
-		failsafe--;
-	}
-
-#if defined(CONFIG_NET_MULTI)
-	reg = hw_p->devnum ? CONFIG_PHY1_ADDR : CONFIG_PHY_ADDR;
-#else
-	reg = CONFIG_PHY_ADDR;
-#endif
-	/* wait for PHY to complete auto negotiation */
-	reg_short = 0;
-#ifndef CONFIG_CS8952_PHY
-	miiphy_read (reg, PHY_BMSR, &reg_short);
-
-	/*
-	 * Wait if PHY is capable of autonegotiation and autonegotiation is not complete
-	 */
-	if ((reg_short & PHY_BMSR_AUTN_ABLE)
-	    && !(reg_short & PHY_BMSR_AUTN_COMP)) {
-		puts ("Waiting for PHY auto negotiation to complete");
-		i = 0;
-		while (!(reg_short & PHY_BMSR_AUTN_COMP)) {
-			/*
-			 * Timeout reached ?
-			 */
-			if (i > PHY_AUTONEGOTIATE_TIMEOUT) {
-				puts (" TIMEOUT !\n");
-				break;
-			}
-
-			if ((i++ % 1000) == 0) {
-				putc ('.');
-			}
-			udelay (1000);	/* 1 ms */
-			miiphy_read (reg, PHY_BMSR, &reg_short);
-		}
-		puts (" done\n");
-		udelay (500000);	/* another 500 ms (results in faster booting) */
-	}
-#endif
-	speed = miiphy_speed (reg);
-	duplex = miiphy_duplex (reg);
-
-	if (hw_p->print_speed) {
-		hw_p->print_speed = 0;
-		printf ("ENET Speed is %d Mbps - %s duplex connection\n",
-			(int) speed, (duplex == HALF) ? "HALF" : "FULL");
-	}
-
-	mtdcr (malmcr, MAL_CR_PLBB | MAL_CR_OPBBL | MAL_CR_LEA | MAL_CR_PLBLT_DEFAULT);
-	/* Errata 1.12: MAL_1 -- Disable MAL bursting */
-	if (get_pvr() == PVR_440GP_RB) {
-		mtdcr (malmcr, mfdcr(malmcr) & ~MAL_CR_PLBB);
-	}
-
-	/* Free "old" buffers */
-	if (hw_p->alloc_tx_buf)
-		free (hw_p->alloc_tx_buf);
-	if (hw_p->alloc_rx_buf)
-		free (hw_p->alloc_rx_buf);
-
-	/*
-	 * Malloc MAL buffer desciptors, make sure they are
-	 * aligned on cache line boundary size
-	 * (401/403/IOP480 = 16, 405 = 32)
-	 * and doesn't cross cache block boundaries.
-	 */
-	hw_p->alloc_tx_buf =
-		(mal_desc_t *) malloc ((sizeof (mal_desc_t) * NUM_TX_BUFF) +
-				       ((2 * CFG_CACHELINE_SIZE) - 2));
-	if (((int) hw_p->alloc_tx_buf & CACHELINE_MASK) != 0) {
-		hw_p->tx =
-			(mal_desc_t *) ((int) hw_p->alloc_tx_buf +
-					CFG_CACHELINE_SIZE -
-					((int) hw_p->
-					 alloc_tx_buf & CACHELINE_MASK));
-	} else {
-		hw_p->tx = hw_p->alloc_tx_buf;
-	}
-
-	hw_p->alloc_rx_buf =
-		(mal_desc_t *) malloc ((sizeof (mal_desc_t) * NUM_RX_BUFF) +
-				       ((2 * CFG_CACHELINE_SIZE) - 2));
-	if (((int) hw_p->alloc_rx_buf & CACHELINE_MASK) != 0) {
-		hw_p->rx =
-			(mal_desc_t *) ((int) hw_p->alloc_rx_buf +
-					CFG_CACHELINE_SIZE -
-					((int) hw_p->
-					 alloc_rx_buf & CACHELINE_MASK));
-	} else {
-		hw_p->rx = hw_p->alloc_rx_buf;
-	}
-
-	for (i = 0; i < NUM_TX_BUFF; i++) {
-		hw_p->tx[i].ctrl = 0;
-		hw_p->tx[i].data_len = 0;
-		if (hw_p->first_init == 0)
-			hw_p->txbuf_ptr =
-				(char *) malloc (ENET_MAX_MTU_ALIGNED);
-		hw_p->tx[i].data_ptr = hw_p->txbuf_ptr;
-		if ((NUM_TX_BUFF - 1) == i)
-			hw_p->tx[i].ctrl |= MAL_TX_CTRL_WRAP;
-		hw_p->tx_run[i] = -1;
-#if 0
-		printf ("TX_BUFF %d @ 0x%08lx\n", i,
-			(ulong) hw_p->tx[i].data_ptr);
-#endif
-	}
-
-	for (i = 0; i < NUM_RX_BUFF; i++) {
-		hw_p->rx[i].ctrl = 0;
-		hw_p->rx[i].data_len = 0;
-		/*       rx[i].data_ptr = (char *) &rx_buff[i]; */
-		hw_p->rx[i].data_ptr = (char *) NetRxPackets[i];
-		if ((NUM_RX_BUFF - 1) == i)
-			hw_p->rx[i].ctrl |= MAL_RX_CTRL_WRAP;
-		hw_p->rx[i].ctrl |= MAL_RX_CTRL_EMPTY | MAL_RX_CTRL_INTR;
-		hw_p->rx_ready[i] = -1;
-#if 0
-		printf ("RX_BUFF %d @ 0x%08lx\n", i, (ulong) rx[i].data_ptr);
-#endif
-	}
-
-	reg = 0x00000000;
-	reg |= dev->enetaddr[0];	/* set high address */
-	reg = reg << 8;
-	reg |= dev->enetaddr[1];
-
-	out32 (EMAC_IAH + hw_p->hw_addr, reg);
-
-	reg = 0x00000000;
-	reg |= dev->enetaddr[2];	/* set low address  */
-	reg = reg << 8;
-	reg |= dev->enetaddr[3];
-	reg = reg << 8;
-	reg |= dev->enetaddr[4];
-	reg = reg << 8;
-	reg |= dev->enetaddr[5];
-
-	out32 (EMAC_IAL + hw_p->hw_addr, reg);
-
-	switch (devnum) {
-#if defined(CONFIG_NET_MULTI)
-	case 1:
-		/* setup MAL tx & rx channel pointers */
-		/* For 405EP, the EMAC1 tx channel 0 is MAL tx channel 2 */
-		mtdcr (maltxctp2r, hw_p->tx);
-		mtdcr (malrxctp1r, hw_p->rx);
-		/* set RX buffer size */
-		mtdcr (malrcbs1, ENET_MAX_MTU_ALIGNED / 16);
-		break;
-#endif
-	case 0:
-	default:
-		/* setup MAL tx & rx channel pointers */
-		mtdcr (maltxctp0r, hw_p->tx);
-		mtdcr (malrxctp0r, hw_p->rx);
-		/* set RX buffer size */
-		mtdcr (malrcbs0, ENET_MAX_MTU_ALIGNED / 16);
-		break;
-	}
-
-	/* Enable MAL transmit and receive channels */
-	mtdcr (maltxcasr, (MAL_TXRX_CASR >> (hw_p->devnum * 2)));
-	mtdcr (malrxcasr, (MAL_TXRX_CASR >> hw_p->devnum));
-
-	/* set transmit enable & receive enable */
-	out32 (EMAC_M0 + hw_p->hw_addr, EMAC_M0_TXE | EMAC_M0_RXE);
-
-	/* set receive fifo to 4k and tx fifo to 2k */
-	mode_reg = in32 (EMAC_M1 + hw_p->hw_addr);
-	mode_reg |= EMAC_M1_RFS_4K | EMAC_M1_TX_FIFO_2K;
-
-	/* set speed */
-	if (speed == _100BASET)
-		mode_reg = mode_reg | EMAC_M1_MF_100MBPS | EMAC_M1_IST;
-	else
-		mode_reg = mode_reg & ~0x00C00000;	/* 10 MBPS */
-	if (duplex == FULL)
-		mode_reg = mode_reg | 0x80000000 | EMAC_M1_IST;
-
-	out32 (EMAC_M1 + hw_p->hw_addr, mode_reg);
-
-#if defined(CONFIG_440)
-	/* set speed in the ZMII bridge */
-	if (speed == _100BASET)
-		out32(ZMII_SSR, in32(ZMII_SSR) | 0x10000000);
-	else
-		out32(ZMII_SSR, in32(ZMII_SSR) & ~0x10000000);
-#if defined(CONFIG_440EP) || defined(CONFIG_440GR)
-	mfsdr(sdr_mfr, reg);
-	/* set speed */
-	if (speed == _100BASET) {
-		out32(ZMII_SSR, in32(ZMII_SSR) | 0x10000000);
-		reg = (reg & ~SDR0_MFR_ZMII_MODE_MASK) | SDR0_MFR_ZMII_MODE_RMII_100M;
-	} else {
-		reg = (reg & ~SDR0_MFR_ZMII_MODE_MASK) | SDR0_MFR_ZMII_MODE_RMII_10M;
-		out32(ZMII_SSR, in32(ZMII_SSR) & ~0x10000000);
-	}
-	mtsdr(sdr_mfr, reg);
-#endif
-#endif
-
-	/* Enable broadcast and indvidual address */
-	/* TBS: enabling runts as some misbehaved nics will send runts */
-	out32 (EMAC_RXM + hw_p->hw_addr, EMAC_RMR_BAE | EMAC_RMR_IAE);
-
-	/* we probably need to set the tx mode1 reg? maybe at tx time */
-
-	/* set transmit request threshold register */
-	out32 (EMAC_TRTR + hw_p->hw_addr, 0x18000000);	/* 256 byte threshold */
-
-#if defined(CONFIG_440)
-	/* 440GP has a 64 byte burst length */
-	out32 (EMAC_RX_HI_LO_WMARK + hw_p->hw_addr, 0x0f002000);
-	out32 (EMAC_TXM1 + hw_p->hw_addr, 0xf8640000);
-#else
-	/* 405s have a 16 byte burst length */
-	out32 (EMAC_RX_HI_LO_WMARK + hw_p->hw_addr, 0x0f002000);
-#endif
-
-	/* Frame gap set */
-	out32 (EMAC_I_FRAME_GAP_REG + hw_p->hw_addr, 0x00000008);
-
-	/* Set EMAC IER */
-	hw_p->emac_ier = EMAC_ISR_PTLE | EMAC_ISR_BFCS |
-		EMAC_ISR_ORE | EMAC_ISR_IRE;
-	if (speed == _100BASET)
-		hw_p->emac_ier = hw_p->emac_ier | EMAC_ISR_SYE;
-
-	out32 (EMAC_ISR + hw_p->hw_addr, 0xffffffff);	/* clear pending interrupts */
-	out32 (EMAC_IER + hw_p->hw_addr, hw_p->emac_ier);
-
-	if (hw_p->first_init == 0) {
-		/*
-		 * Connect interrupt service routines
-		 */
-		irq_install_handler (VECNUM_ETH0 + (hw_p->devnum * 2),
-				     (interrupt_handler_t *) enetInt, dev);
-	}
-
-	mtmsr (msr);		/* enable interrupts again */
-
-	hw_p->bis = bis;
-	hw_p->first_init = 1;
-
-	return (1);
-}
-
-
-static int ppc_4xx_eth_send (struct eth_device *dev, volatile void *ptr, int len)
-{
-	struct enet_frame *ef_ptr;
-	ulong time_start, time_now;
-	unsigned long temp_txm0;
-	EMAC_405_HW_PST hw_p = dev->priv;
-
-	ef_ptr = (struct enet_frame *) ptr;
-
-	/*-----------------------------------------------------------------------+
-	 *  Copy in our address into the frame.
-	 *-----------------------------------------------------------------------*/
-	(void) memcpy (ef_ptr->source_addr, dev->enetaddr, ENET_ADDR_LENGTH);
-
-	/*-----------------------------------------------------------------------+
-	 * If frame is too long or too short, modify length.
-	 *-----------------------------------------------------------------------*/
-	/* TBS: where does the fragment go???? */
-	if (len > ENET_MAX_MTU)
-		len = ENET_MAX_MTU;
-
-	/*   memcpy ((void *) &tx_buff[tx_slot], (const void *) ptr, len); */
-	memcpy ((void *) hw_p->txbuf_ptr, (const void *) ptr, len);
-
-	/*-----------------------------------------------------------------------+
-	 * set TX Buffer busy, and send it
-	 *-----------------------------------------------------------------------*/
-	hw_p->tx[hw_p->tx_slot].ctrl = (MAL_TX_CTRL_LAST |
-					EMAC_TX_CTRL_GFCS | EMAC_TX_CTRL_GP) &
-		~(EMAC_TX_CTRL_ISA | EMAC_TX_CTRL_RSA);
-	if ((NUM_TX_BUFF - 1) == hw_p->tx_slot)
-		hw_p->tx[hw_p->tx_slot].ctrl |= MAL_TX_CTRL_WRAP;
-
-	hw_p->tx[hw_p->tx_slot].data_len = (short) len;
-	hw_p->tx[hw_p->tx_slot].ctrl |= MAL_TX_CTRL_READY;
-
-	__asm__ volatile ("eieio");
-
-	out32 (EMAC_TXM0 + hw_p->hw_addr,
-	       in32 (EMAC_TXM0 + hw_p->hw_addr) | EMAC_TXM0_GNP0);
-#ifdef INFO_405_ENET
-	hw_p->stats.pkts_tx++;
-#endif
-
-	/*-----------------------------------------------------------------------+
-	 * poll unitl the packet is sent and then make sure it is OK
-	 *-----------------------------------------------------------------------*/
-	time_start = get_timer (0);
-	while (1) {
-		temp_txm0 = in32 (EMAC_TXM0 + hw_p->hw_addr);
-		/* loop until either TINT turns on or 3 seconds elapse */
-		if ((temp_txm0 & EMAC_TXM0_GNP0) != 0) {
-			/* transmit is done, so now check for errors
-			 * If there is an error, an interrupt should
-			 * happen when we return
-			 */
-			time_now = get_timer (0);
-			if ((time_now - time_start) > 3000) {
-				return (-1);
-			}
-		} else {
-			return (len);
-		}
-	}
-}
-
-#if defined(CONFIG_440)
-int enetInt (struct eth_device *dev)
-{
-	int serviced;
-	int rc = -1;				/* default to not us */
-	unsigned long mal_isr;
-	unsigned long emac_isr = 0;
-	unsigned long mal_rx_eob;
-	unsigned long my_uic0msr, my_uic1msr;
-	EMAC_405_HW_PST hw_p;
-
-	/*
-	 * Because the mal is generic, we need to get the current
-	 * eth device
-	 */
-#if defined(CONFIG_NET_MULTI)
-	dev = eth_get_dev();
-#else
-	dev = emac0_dev;
-#endif
-	hw_p = dev->priv;
-
-	/* enter loop that stays in interrupt code until nothing to service */
-	do {
-		serviced = 0;
-
-		my_uic0msr = mfdcr (uic0msr);
-		my_uic1msr = mfdcr (uic1msr);
-
-		if (!(my_uic0msr & UIC_MRE)
-		    && !(my_uic1msr & (UIC_ETH0 | UIC_MS | UIC_MTDE | UIC_MRDE))) {
-			/* not for us */
-			return (rc);
-		}
-
-		/* get and clear controller status interrupts */
-		/* look at Mal and EMAC interrupts */
-		if ((my_uic0msr & UIC_MRE)
-		    || (my_uic1msr & (UIC_MS | UIC_MTDE | UIC_MRDE))) {
-			/* we have a MAL interrupt */
-			mal_isr = mfdcr (malesr);
-			/* look for mal error */
-			if (my_uic1msr & (UIC_MS | UIC_MTDE | UIC_MRDE)) {
-				mal_err (dev, mal_isr, my_uic0msr, MAL_UIC_DEF, MAL_UIC_ERR);
-				serviced = 1;
-				rc = 0;
-			}
-		}
-		if (UIC_ETH0 & my_uic1msr) {	/* look for EMAC errors */
-			emac_isr = in32 (EMAC_ISR + hw_p->hw_addr);
-			if ((hw_p->emac_ier & emac_isr) != 0) {
-				emac_err (dev, emac_isr);
-				serviced = 1;
-				rc = 0;
-			}
-		}
-		if ((hw_p->emac_ier & emac_isr)
-		    || (my_uic1msr & (UIC_MS | UIC_MTDE | UIC_MRDE))) {
-			mtdcr (uic0sr, UIC_MRE); /* Clear */
-			mtdcr (uic1sr, UIC_ETH0 | UIC_MS | UIC_MTDE | UIC_MRDE); /* Clear */
-			return (rc);		/* we had errors so get out */
-		}
-
-		/* handle MAL RX EOB  interupt from a receive */
-		/* check for EOB on valid channels            */
-		if (my_uic0msr & UIC_MRE) {
-			mal_rx_eob = mfdcr (malrxeobisr);
-			if ((mal_rx_eob & (0x80000000 >> hw_p->devnum)) != 0) {	/* call emac routine for channel 0 */
-				/* clear EOB
-				   mtdcr(malrxeobisr, mal_rx_eob); */
-				enet_rcv (dev, emac_isr);
-				/* indicate that we serviced an interrupt */
-				serviced = 1;
-				rc = 0;
-			}
-		}
-		mtdcr (uic0sr, UIC_MRE); /* Clear */
-		mtdcr (uic1sr, UIC_ETH0 | UIC_MS | UIC_MTDE | UIC_MRDE); /* Clear */
-	} while (serviced);
-
-	return (rc);
-}
-
-#else /* CONFIG_440 */
-
-int enetInt (struct eth_device *dev)
-{
-	int serviced;
-	int rc = -1;		/* default to not us */
-	unsigned long mal_isr;
-	unsigned long emac_isr = 0;
-	unsigned long mal_rx_eob;
-	unsigned long my_uicmsr;
-
-	EMAC_405_HW_PST hw_p;
-
-	/*
-	 * Because the mal is generic, we need to get the current
-	 * eth device
-	 */
-#if defined(CONFIG_NET_MULTI)
-	dev = eth_get_dev();
-#else
-	dev = emac0_dev;
-#endif
-
-	hw_p = dev->priv;
-
-	/* enter loop that stays in interrupt code until nothing to service */
-	do {
-		serviced = 0;
-
-		my_uicmsr = mfdcr (uicmsr);
-
-		if ((my_uicmsr & (MAL_UIC_DEF | EMAC_UIC_DEF)) == 0) {	/* not for us */
-			return (rc);
-		}
-		/* get and clear controller status interrupts */
-		/* look at Mal and EMAC interrupts */
-		if ((MAL_UIC_DEF & my_uicmsr) != 0) {	/* we have a MAL interrupt */
-			mal_isr = mfdcr (malesr);
-			/* look for mal error */
-			if ((my_uicmsr & MAL_UIC_ERR) != 0) {
-				mal_err (dev, mal_isr, my_uicmsr, MAL_UIC_DEF, MAL_UIC_ERR);
-				serviced = 1;
-				rc = 0;
-			}
-		}
-
-		/* port by port dispatch of emac interrupts */
-
-		if ((SEL_UIC_DEF(hw_p->devnum) & my_uicmsr) != 0) {	/* look for EMAC errors */
-			emac_isr = in32 (EMAC_ISR + hw_p->hw_addr);
-			if ((hw_p->emac_ier & emac_isr) != 0) {
-				emac_err (dev, emac_isr);
-				serviced = 1;
-				rc = 0;
-			}
-		}
-		if (((hw_p->emac_ier & emac_isr) != 0) || ((MAL_UIC_ERR & my_uicmsr) != 0)) {
-			mtdcr (uicsr, MAL_UIC_DEF | SEL_UIC_DEF(hw_p->devnum)); /* Clear */
-			return (rc);		/* we had errors so get out */
-		}
-
-		/* handle MAX TX EOB interrupt from a tx */
-		if (my_uicmsr & UIC_MAL_TXEOB) {
-			mal_rx_eob = mfdcr (maltxeobisr);
-			mtdcr (maltxeobisr, mal_rx_eob);
-			mtdcr (uicsr, UIC_MAL_TXEOB);
-		}
-		/* handle MAL RX EOB  interupt from a receive */
-		/* check for EOB on valid channels	      */
-		if (my_uicmsr & UIC_MAL_RXEOB)
-		{
-			mal_rx_eob = mfdcr (malrxeobisr);
-			if ((mal_rx_eob & (0x80000000 >> hw_p->devnum)) != 0) {	/* call emac routine for channel x */
-				/* clear EOB
-				 mtdcr(malrxeobisr, mal_rx_eob); */
-				enet_rcv (dev, emac_isr);
-				/* indicate that we serviced an interrupt */
-				serviced = 1;
-				rc = 0;
-			}
-		}
-		mtdcr (uicsr, MAL_UIC_DEF|EMAC_UIC_DEF|EMAC_UIC_DEF1);	/* Clear */
-	}
-	while (serviced);
-
-	return (rc);
-}
-#endif
-/*-----------------------------------------------------------------------------+
- *  MAL Error Routine
- *-----------------------------------------------------------------------------*/
-static void mal_err (struct eth_device *dev, unsigned long isr,
-		     unsigned long uic, unsigned long maldef,
-		     unsigned long mal_errr)
-{
-	EMAC_405_HW_PST hw_p = dev->priv;
-
-	mtdcr (malesr, isr);	/* clear interrupt */
-
-	/* clear DE interrupt */
-	mtdcr (maltxdeir, 0xC0000000);
-	mtdcr (malrxdeir, 0x80000000);
-
-#ifdef INFO_405_ENET
-	printf ("\nMAL error occured.... ISR = %lx UIC = = %lx  MAL_DEF = %lx  MAL_ERR= %lx \n", isr, uic, maldef, mal_errr);
-#endif
-
-	eth_init (hw_p->bis);	/* start again... */
-}
-
-/*-----------------------------------------------------------------------------+
- *  EMAC Error Routine
- *-----------------------------------------------------------------------------*/
-static void emac_err (struct eth_device *dev, unsigned long isr)
-{
-	EMAC_405_HW_PST hw_p = dev->priv;
-
-	printf ("EMAC%d error occured.... ISR = %lx\n", hw_p->devnum, isr);
-	out32 (EMAC_ISR + hw_p->hw_addr, isr);
-}
-
-/*-----------------------------------------------------------------------------+
- *  enet_rcv() handles the ethernet receive data
- *-----------------------------------------------------------------------------*/
-static void enet_rcv (struct eth_device *dev, unsigned long malisr)
-{
-	struct enet_frame *ef_ptr;
-	unsigned long data_len;
-	unsigned long rx_eob_isr;
-	EMAC_405_HW_PST hw_p = dev->priv;
-
-	int handled = 0;
-	int i;
-	int loop_count = 0;
-
-	rx_eob_isr = mfdcr (malrxeobisr);
-	if ((0x80000000 >> hw_p->devnum) & rx_eob_isr) {
-		/* clear EOB */
-		mtdcr (malrxeobisr, rx_eob_isr);
-
-		/* EMAC RX done */
-		while (1) {	/* do all */
-			i = hw_p->rx_slot;
-
-			if ((MAL_RX_CTRL_EMPTY & hw_p->rx[i].ctrl)
-			    || (loop_count >= NUM_RX_BUFF))
-				break;
-			loop_count++;
-			hw_p->rx_slot++;
-			if (NUM_RX_BUFF == hw_p->rx_slot)
-				hw_p->rx_slot = 0;
-			handled++;
-			data_len = (unsigned long) hw_p->rx[i].data_len;	/* Get len */
-			if (data_len) {
-				if (data_len > ENET_MAX_MTU)	/* Check len */
-					data_len = 0;
-				else {
-					if (EMAC_RX_ERRORS & hw_p->rx[i].ctrl) {	/* Check Errors */
-						data_len = 0;
-						hw_p->stats.rx_err_log[hw_p->
-								       rx_err_index]
-							= hw_p->rx[i].ctrl;
-						hw_p->rx_err_index++;
-						if (hw_p->rx_err_index ==
-						    MAX_ERR_LOG)
-							hw_p->rx_err_index =
-								0;
-					}	/* emac_erros */
-				}	/* data_len < max mtu */
-			}	/* if data_len */
-			if (!data_len) {	/* no data */
-				hw_p->rx[i].ctrl |= MAL_RX_CTRL_EMPTY;	/* Free Recv Buffer */
-
-				hw_p->stats.data_len_err++;	/* Error at Rx */
-			}
-
-			/* !data_len */
-			/* AS.HARNOIS */
-			/* Check if user has already eaten buffer */
-			/* if not => ERROR */
-			else if (hw_p->rx_ready[hw_p->rx_i_index] != -1) {
-				if (hw_p->is_receiving)
-					printf ("ERROR : Receive buffers are full!\n");
-				break;
-			} else {
-				hw_p->stats.rx_frames++;
-				hw_p->stats.rx += data_len;
-				ef_ptr = (struct enet_frame *) hw_p->rx[i].
-					data_ptr;
-#ifdef INFO_405_ENET
-				hw_p->stats.pkts_rx++;
-#endif
-				/* AS.HARNOIS
-				 * use ring buffer
-				 */
-				hw_p->rx_ready[hw_p->rx_i_index] = i;
-				hw_p->rx_i_index++;
-				if (NUM_RX_BUFF == hw_p->rx_i_index)
-					hw_p->rx_i_index = 0;
-
-				/* printf("X");  /|* test-only *|/ */
-
-				/*  AS.HARNOIS
-				 * free receive buffer only when
-				 * buffer has been handled (eth_rx)
-				 rx[i].ctrl |= MAL_RX_CTRL_EMPTY;
-				 */
-			}	/* if data_len */
-		}		/* while */
-	}			/* if EMACK_RXCHL */
-}
-
-
-static int ppc_4xx_eth_rx (struct eth_device *dev)
-{
-	int length;
-	int user_index;
-	unsigned long msr;
-	EMAC_405_HW_PST hw_p = dev->priv;
-
-	hw_p->is_receiving = 1;	/* tell driver */
-
-	for (;;) {
-		/* AS.HARNOIS
-		 * use ring buffer and
-		 * get index from rx buffer desciptor queue
-		 */
-		user_index = hw_p->rx_ready[hw_p->rx_u_index];
-		if (user_index == -1) {
-			length = -1;
-			break;	/* nothing received - leave for() loop */
-		}
-
-		msr = mfmsr ();
-		mtmsr (msr & ~(MSR_EE));
-
-		length = hw_p->rx[user_index].data_len;
-
-		/* Pass the packet up to the protocol layers. */
-		/*       NetReceive(NetRxPackets[rxIdx], length - 4); */
-		/*       NetReceive(NetRxPackets[i], length); */
-		NetReceive (NetRxPackets[user_index], length - 4);
-		/* Free Recv Buffer */
-		hw_p->rx[user_index].ctrl |= MAL_RX_CTRL_EMPTY;
-		/* Free rx buffer descriptor queue */
-		hw_p->rx_ready[hw_p->rx_u_index] = -1;
-		hw_p->rx_u_index++;
-		if (NUM_RX_BUFF == hw_p->rx_u_index)
-			hw_p->rx_u_index = 0;
-
-#ifdef INFO_405_ENET
-		hw_p->stats.pkts_handled++;
-#endif
-
-		mtmsr (msr);	/* Enable IRQ's */
-	}
-
-	hw_p->is_receiving = 0;	/* tell driver */
-
-	return length;
-}
-
-static int virgin = 0;
-int ppc_4xx_eth_initialize (bd_t * bis)
-{
-	struct eth_device *dev;
-	int eth_num = 0;
-
-	EMAC_405_HW_PST hw = NULL;
-
-	for (eth_num = 0; eth_num < EMAC_NUM_DEV; eth_num++) {
-
-		/* Allocate device structure */
-		dev = (struct eth_device *) malloc (sizeof (*dev));
-		if (dev == NULL) {
-			printf ("ppc_405x_eth_initialize: "
-				"Cannot allocate eth_device %d\n", eth_num);
-			return (-1);
-		}
-		memset(dev, 0, sizeof(*dev));
-		/* Allocate our private use data */
-		hw = (EMAC_405_HW_PST) malloc (sizeof (*hw));
-		if (hw == NULL) {
-			printf ("ppc_405x_eth_initialize: "
-				"Cannot allocate private hw data for eth_device %d",
-				eth_num);
-			free (dev);
-			return (-1);
-		}
-		memset(hw, 0, sizeof(*hw));
-
-		switch (eth_num) {
-		case 0:
-			hw->hw_addr = 0;
-			memcpy (dev->enetaddr, bis->bi_enetaddr, 6);
-			break;
-#if defined(CONFIG_NET_MULTI)
-		case 1:
-			hw->hw_addr = 0x100;
-			memcpy (dev->enetaddr, bis->bi_enet1addr, 6);
-			break;
-#endif
-		default:
-			hw->hw_addr = 0;
-			memcpy (dev->enetaddr, bis->bi_enetaddr, 6);
-			break;
-		}
-
-		hw->devnum = eth_num;
-		hw->print_speed = 1;
-
-		sprintf (dev->name, "ppc_405x_eth%d", eth_num);
-		dev->priv = (void *) hw;
-		dev->init = ppc_4xx_eth_init;
-		dev->halt = ppc_4xx_eth_halt;
-		dev->send = ppc_4xx_eth_send;
-		dev->recv = ppc_4xx_eth_rx;
-
-		if (0 == virgin) {
-			/* set the MAL IER ??? names may change with new spec ??? */
-			mal_ier =
-				MAL_IER_DE | MAL_IER_NE | MAL_IER_TE |
-				MAL_IER_OPBE | MAL_IER_PLBE;
-			mtdcr (malesr, 0xffffffff);	/* clear pending interrupts */
-			mtdcr (maltxdeir, 0xffffffff);	/* clear pending interrupts */
-			mtdcr (malrxdeir, 0xffffffff);	/* clear pending interrupts */
-			mtdcr (malier, mal_ier);
-
-			/* install MAL interrupt handler */
-			irq_install_handler (VECNUM_MS,
-					     (interrupt_handler_t *) enetInt,
-					     dev);
-			irq_install_handler (VECNUM_MTE,
-					     (interrupt_handler_t *) enetInt,
-					     dev);
-			irq_install_handler (VECNUM_MRE,
-					     (interrupt_handler_t *) enetInt,
-					     dev);
-			irq_install_handler (VECNUM_TXDE,
-					     (interrupt_handler_t *) enetInt,
-					     dev);
-			irq_install_handler (VECNUM_RXDE,
-					     (interrupt_handler_t *) enetInt,
-					     dev);
-			virgin = 1;
-		}
-
-#if defined(CONFIG_NET_MULTI)
-		eth_register (dev);
-#else
-		emac0_dev = dev;
-#endif
-
-	}			/* end for each supported device */
-
-	return (1);
-}
-
-#if !defined(CONFIG_NET_MULTI)
-void eth_halt (void) {
-	if (emac0_dev) {
-		ppc_4xx_eth_halt(emac0_dev);
-		free(emac0_dev);
-		emac0_dev = NULL;
-	}
-}
-
-int eth_init (bd_t *bis)
-{
-	ppc_4xx_eth_initialize(bis);
-	return(ppc_4xx_eth_init(emac0_dev, bis));
-}
-
-int eth_send(volatile void *packet, int length)
-{
-
-	return (ppc_4xx_eth_send(emac0_dev, packet, length));
-}
-
-int eth_rx(void)
-{
-	return (ppc_4xx_eth_rx(emac0_dev));
-}
-#endif
-
-#endif /* CONFIG_405 */
diff --git a/cpu/ppc4xx/440gx_enet.c b/cpu/ppc4xx/4xx_enet.c
index d0b6c15864..7766f9aaa3 100644
--- a/cpu/ppc4xx/440gx_enet.c
+++ b/cpu/ppc4xx/4xx_enet.c
@@ -72,27 +72,37 @@
  *              - ported from 405gp_enet.c to utilized upto 4 EMAC ports
  *                in the 440GX.  This port should work with the 440GP
  *                (2 EMACs) also
+ *  15-Aug-05   sr@denx.de
+ *              - merged 405gp_enet.c and 440gx_enet.c to generic 4xx_enet.c
+                  now handling all 4xx cpu's.
  *-----------------------------------------------------------------------------*/
 
 #include <config.h>
-#if defined(CONFIG_440) && defined(CONFIG_NET_MULTI)
-
 #include <common.h>
 #include <net.h>
 #include <asm/processor.h>
-#include <ppc440.h>
 #include <commproc.h>
-#include <440gx_enet.h>
+#include <ppc4xx.h>
+#include <ppc4xx_enet.h>
 #include <405_mal.h>
 #include <miiphy.h>
 #include <malloc.h>
 #include "vecnum.h"
 
+/*
+ * Only compile for platform with IBM/AMCC EMAC ethernet controller and
+ * network support enabled.
+ * Remark: CONFIG_405 describes Xilinx PPC405 FPGA without EMAC controller!
+ */
+#if (CONFIG_COMMANDS & CFG_CMD_NET) && !defined(CONFIG_405) && !defined(CONFIG_IOP480)
+
+#if !(defined(CONFIG_MII) || (CONFIG_COMMANDS & CFG_CMD_MII))
+#error "CONFIG_MII has to be defined!"
+#endif
 
 #define EMAC_RESET_TIMEOUT 1000	/* 1000 ms reset timeout */
 #define PHY_AUTONEGOTIATE_TIMEOUT 4000	/* 4000 ms autonegotiate timeout */
 
-
 /* Ethernet Transmit and Receive Buffers */
 /* AS.HARNOIS
  * In the same way ENET_MAX_MTU and ENET_MAX_MTU_ALIGNED are set from
@@ -101,7 +111,6 @@
 #define ENET_MAX_MTU           PKTSIZE
 #define ENET_MAX_MTU_ALIGNED   PKTSIZE_ALIGN
 
-
 /* define the number of channels implemented */
 #define EMAC_RXCHL      EMAC_NUM_DEV
 #define EMAC_TXCHL      EMAC_NUM_DEV
@@ -113,19 +122,27 @@
 #define MAL_UIC_ERR ( UIC_MAL_SERR | UIC_MAL_TXDE  | UIC_MAL_RXDE)
 #define MAL_UIC_DEF  (UIC_MAL_RXEOB | MAL_UIC_ERR)
 #define EMAC_UIC_DEF UIC_ENET
+#define EMAC_UIC_DEF1 UIC_ENET1
+#define SEL_UIC_DEF(p) (p ? UIC_ENET1 : UIC_ENET )
 
-#undef INFO_440_ENET
+#undef INFO_4XX_ENET
 
 #define BI_PHYMODE_NONE  0
 #define BI_PHYMODE_ZMII  1
 #define BI_PHYMODE_RGMII 2
 
+
 /*-----------------------------------------------------------------------------+
  * Global variables. TX and RX descriptors and buffers.
  *-----------------------------------------------------------------------------*/
 /* IER globals */
 static uint32_t mal_ier;
 
+#if !defined(CONFIG_NET_MULTI)
+struct eth_device *emac0_dev;
+#endif
+
+
 /*-----------------------------------------------------------------------------+
  * Prototypes and externals.
  *-----------------------------------------------------------------------------*/
@@ -137,31 +154,33 @@ static void mal_err (struct eth_device *dev, unsigned long isr,
 		     unsigned long mal_errr);
 static void emac_err (struct eth_device *dev, unsigned long isr);
 
+
 /*-----------------------------------------------------------------------------+
-| ppc_440x_eth_halt
+| ppc_4xx_eth_halt
 | Disable MAL channel, and EMACn
-|
-|
 +-----------------------------------------------------------------------------*/
-static void ppc_440x_eth_halt (struct eth_device *dev)
+static void ppc_4xx_eth_halt (struct eth_device *dev)
 {
-	EMAC_440GX_HW_PST hw_p = dev->priv;
+	EMAC_4XX_HW_PST hw_p = dev->priv;
 	uint32_t failsafe = 10000;
 
 	out32 (EMAC_IER + hw_p->hw_addr, 0x00000000);	/* disable emac interrupts */
 
 	/* 1st reset MAL channel */
 	/* Note: writing a 0 to a channel has no effect */
+#if defined(CONFIG_405EP) || defined(CONFIG_440EP) || defined(CONFIG_440GR)
+	mtdcr (maltxcarr, (MAL_CR_MMSR >> (hw_p->devnum * 2)));
+#else
 	mtdcr (maltxcarr, (MAL_CR_MMSR >> hw_p->devnum));
+#endif
 	mtdcr (malrxcarr, (MAL_CR_MMSR >> hw_p->devnum));
 
 	/* wait for reset */
-	while (mfdcr (maltxcasr) & (MAL_CR_MMSR >> hw_p->devnum)) {
+	while (mfdcr (malrxcasr) & (MAL_CR_MMSR >> hw_p->devnum)) {
 		udelay (1000);	/* Delay 1 MS so as not to hammer the register */
 		failsafe--;
 		if (failsafe == 0)
 			break;
-
 	}
 
 	/* EMAC RESET */
@@ -176,7 +195,7 @@ extern int phy_setup_aneg (unsigned char addr);
 extern int miiphy_reset (unsigned char addr);
 
 #if defined (CONFIG_440GX)
-int ppc_440x_eth_setup_bridge(int devnum, bd_t * bis)
+int ppc_4xx_eth_setup_bridge(int devnum, bd_t * bis)
 {
 	unsigned long pfc1;
 	unsigned long zmiifer;
@@ -267,10 +286,10 @@ int ppc_440x_eth_setup_bridge(int devnum, bd_t * bis)
 }
 #endif
 
-static int ppc_440x_eth_init (struct eth_device *dev, bd_t * bis)
+static int ppc_4xx_eth_init (struct eth_device *dev, bd_t * bis)
 {
 	int i, j;
-	unsigned long reg;
+	unsigned long reg = 0;
 	unsigned long msr;
 	unsigned long speed;
 	unsigned long duplex;
@@ -278,27 +297,29 @@ static int ppc_440x_eth_init (struct eth_device *dev, bd_t * bis)
 	unsigned mode_reg;
 	unsigned short devnum;
 	unsigned short reg_short;
-	sys_info_t sysinfo;
 #if defined(CONFIG_440GX)
+	sys_info_t sysinfo;
 	int ethgroup;
 #endif
 
-	EMAC_440GX_HW_PST hw_p = dev->priv;
+	EMAC_4XX_HW_PST hw_p = dev->priv;
 
 	/* before doing anything, figure out if we have a MAC address */
 	/* if not, bail */
 	if (memcmp (dev->enetaddr, "\0\0\0\0\0\0", 6) == 0)
 		return -1;
 
+#if defined(CONFIG_440GX)
 	/* Need to get the OPB frequency so we can access the PHY */
 	get_sys_info (&sysinfo);
+#endif
 
 	msr = mfmsr ();
 	mtmsr (msr & ~(MSR_EE));	/* disable interrupts */
 
 	devnum = hw_p->devnum;
 
-#ifdef INFO_440_ENET
+#ifdef INFO_4XX_ENET
 	/* AS.HARNOIS
 	 * We should have :
 	 * hw_p->stats.pkts_handled <=  hw_p->stats.pkts_rx <= hw_p->stats.pkts_handled+PKTBUFSRX
@@ -320,29 +341,6 @@ static int ppc_440x_eth_init (struct eth_device *dev, bd_t * bis)
 	hw_p->stats.pkts_handled = 0;
 #endif
 
-	/* MAL Channel RESET */
-	/* 1st reset MAL channel */
-	/* Note: writing a 0 to a channel has no effect */
-#if defined(CONFIG_440EP) || defined(CONFIG_440GR)
-	mtdcr (maltxcarr, (MAL_TXRX_CASR >> (hw_p->devnum*2)));
-#else
-	mtdcr (maltxcarr, (MAL_TXRX_CASR >> hw_p->devnum));
-#endif
-
-	mtdcr (malrxcarr, (MAL_TXRX_CASR >> hw_p->devnum));
-
-	/* wait for reset */
-	/* TBS:  should have udelay and failsafe here */
-	failsafe = 10000;
-	/* wait for reset */
-	while (mfdcr (maltxcasr) & (MAL_CR_MMSR >> hw_p->devnum)) {
-		udelay (1000);	/* Delay 1 MS so as not to hammer the register */
-		failsafe--;
-		if (failsafe == 0)
-			break;
-
-	}
-
 	hw_p->tx_err_index = 0;	/* Transmit Error Index for tx_err_log */
 	hw_p->rx_err_index = 0;	/* Receive Error Index for rx_err_log */
 
@@ -354,6 +352,7 @@ static int ppc_440x_eth_init (struct eth_device *dev, bd_t * bis)
 	hw_p->tx_i_index = 0;	/* Transmit Interrupt Queue Index */
 	hw_p->tx_u_index = 0;	/* Transmit User Queue Index */
 
+#if defined(CONFIG_440)
 	/* set RMII mode */
 	/* NOTE: 440GX spec states that mode is mutually exclusive */
 	/* NOTE: Therefore, disable all other EMACS, since we handle */
@@ -365,7 +364,7 @@ static int ppc_440x_eth_init (struct eth_device *dev, bd_t * bis)
 #if defined(CONFIG_440EP) || defined(CONFIG_440GR)
    	out32 (ZMII_FER, (ZMII_FER_RMII | ZMII_FER_MDI) << ZMII_FER_V (devnum));
 #elif defined(CONFIG_440GX)
-	ethgroup = ppc_440x_eth_setup_bridge(devnum, bis);
+	ethgroup = ppc_4xx_eth_setup_bridge(devnum, bis);
 #else
 	if ((devnum == 0) || (devnum == 1)) {
 		out32 (ZMII_FER, (ZMII_FER_SMII | ZMII_FER_MDI) << ZMII_FER_V (devnum));
@@ -378,6 +377,8 @@ static int ppc_440x_eth_init (struct eth_device *dev, bd_t * bis)
 #endif
 
 	out32 (ZMII_SSR, ZMII_SSR_SP << ZMII_SSR_V(devnum));
+#endif /* defined(CONFIG_440) */
+
 	__asm__ volatile ("eieio");
 
 	/* reset emac so we have access to the phy */
@@ -415,9 +416,11 @@ static int ppc_440x_eth_init (struct eth_device *dev, bd_t * bis)
 	case 0:
 		reg = CONFIG_PHY_ADDR;
 		break;
+#if defined (CONFIG_PHY1_ADDR)
 	case 1:
 		reg = CONFIG_PHY1_ADDR;
 		break;
+#endif
 #if defined (CONFIG_440GX)
 	case 2:
 		reg = CONFIG_PHY2_ADDR;
@@ -433,7 +436,7 @@ static int ppc_440x_eth_init (struct eth_device *dev, bd_t * bis)
 
 	bis->bi_phynum[devnum] = reg;
 
-#ifndef CONFIG_NO_PHY_RESET
+#if defined(CONFIG_PHY_RESET)
 	/*
 	 * Reset the phy, only if its the first time through
 	 * otherwise, just check the speeds & feeds
@@ -476,7 +479,7 @@ static int ppc_440x_eth_init (struct eth_device *dev, bd_t * bis)
 		phy_setup_aneg (reg);
 		udelay (1000);
 	}
-#endif /* CONFIG_NO_PHY_RESET */
+#endif /* defined(CONFIG_PHY_RESET) */
 
 	miiphy_read (reg, PHY_BMSR, &reg_short);
 
@@ -506,7 +509,8 @@ static int ppc_440x_eth_init (struct eth_device *dev, bd_t * bis)
 		puts (" done\n");
 		udelay (500000);	/* another 500 ms (results in faster booting) */
 	}
-#endif
+#endif /* #ifndef CONFIG_CS8952_PHY */
+
 	speed = miiphy_speed (reg);
 	duplex = miiphy_duplex (reg);
 
@@ -516,6 +520,7 @@ static int ppc_440x_eth_init (struct eth_device *dev, bd_t * bis)
 			(int) speed, (duplex == HALF) ? "HALF" : "FULL");
 	}
 
+#if defined(CONFIG_440)
 #if defined(CONFIG_440EP) || defined(CONFIG_440GR)
 	mfsdr(sdr_mfr, reg);
 	if (speed == 100) {
@@ -543,6 +548,7 @@ static int ppc_440x_eth_init (struct eth_device *dev, bd_t * bis)
 
 		out32 (RGMII_SSR, reg);
 	}
+#endif /* defined(CONFIG_440) */
 
 	/* set the Mal configuration reg */
 #if defined(CONFIG_440GX)
@@ -665,13 +671,15 @@ static int ppc_440x_eth_init (struct eth_device *dev, bd_t * bis)
 	switch (devnum) {
 	case 1:
 		/* setup MAL tx & rx channel pointers */
-#if defined (CONFIG_440EP) || defined (CONFIG_440GR)
+#if defined (CONFIG_405EP) || defined (CONFIG_440EP) || defined (CONFIG_440GR)
 		mtdcr (maltxctp2r, hw_p->tx);
 #else
 		mtdcr (maltxctp1r, hw_p->tx);
 #endif
+#if defined(CONFIG_440)
 		mtdcr (maltxbattr, 0x0);
 		mtdcr (malrxbattr, 0x0);
+#endif
 		mtdcr (malrxctp1r, hw_p->rx);
 		/* set RX buffer size */
 		mtdcr (malrcbs1, ENET_MAX_MTU_ALIGNED / 16);
@@ -680,8 +688,8 @@ static int ppc_440x_eth_init (struct eth_device *dev, bd_t * bis)
 	case 2:
 		/* setup MAL tx & rx channel pointers */
 		mtdcr (maltxbattr, 0x0);
-		mtdcr (maltxctp2r, hw_p->tx);
 		mtdcr (malrxbattr, 0x0);
+		mtdcr (maltxctp2r, hw_p->tx);
 		mtdcr (malrxctp2r, hw_p->rx);
 		/* set RX buffer size */
 		mtdcr (malrcbs2, ENET_MAX_MTU_ALIGNED / 16);
@@ -699,9 +707,11 @@ static int ppc_440x_eth_init (struct eth_device *dev, bd_t * bis)
 	case 0:
 	default:
 		/* setup MAL tx & rx channel pointers */
+#if defined(CONFIG_440)
 		mtdcr (maltxbattr, 0x0);
-		mtdcr (maltxctp0r, hw_p->tx);
 		mtdcr (malrxbattr, 0x0);
+#endif
+		mtdcr (maltxctp0r, hw_p->tx);
 		mtdcr (malrxctp0r, hw_p->rx);
 		/* set RX buffer size */
 		mtdcr (malrcbs0, ENET_MAX_MTU_ALIGNED / 16);
@@ -709,7 +719,7 @@ static int ppc_440x_eth_init (struct eth_device *dev, bd_t * bis)
 	}
 
 	/* Enable MAL transmit and receive channels */
-#if defined(CONFIG_440EP) || defined(CONFIG_440GR)
+#if defined(CONFIG_405EP) || defined(CONFIG_440EP) || defined(CONFIG_440GR)
 	mtdcr (maltxcasr, (MAL_TXRX_CASR >> (hw_p->devnum*2)));
 #else
 	mtdcr (maltxcasr, (MAL_TXRX_CASR >> hw_p->devnum));
@@ -745,8 +755,13 @@ static int ppc_440x_eth_init (struct eth_device *dev, bd_t * bis)
 	out32 (EMAC_TRTR + hw_p->hw_addr, 0x18000000);	/* 256 byte threshold */
 
 	/* set receive  low/high water mark register */
+#if defined(CONFIG_440)
 	/* 440GP has a 64 byte burst length */
 	out32 (EMAC_RX_HI_LO_WMARK + hw_p->hw_addr, 0x80009000);
+#else
+	/* 405s have a 16 byte burst length */
+	out32 (EMAC_RX_HI_LO_WMARK + hw_p->hw_addr, 0x0f002000);
+#endif /* defined(CONFIG_440) */
 	out32 (EMAC_TXM1 + hw_p->hw_addr, 0xf8640000);
 
 	/* Set fifo limit entry in tx mode 0 */
@@ -755,8 +770,7 @@ static int ppc_440x_eth_init (struct eth_device *dev, bd_t * bis)
 	out32 (EMAC_I_FRAME_GAP_REG + hw_p->hw_addr, 0x00000008);
 
 	/* Set EMAC IER */
-	hw_p->emac_ier = EMAC_ISR_PTLE | EMAC_ISR_BFCS |
-		EMAC_ISR_PTLE | EMAC_ISR_ORE | EMAC_ISR_IRE;
+	hw_p->emac_ier = EMAC_ISR_PTLE | EMAC_ISR_BFCS | EMAC_ISR_ORE | EMAC_ISR_IRE;
 	if (speed == _100BASET)
 		hw_p->emac_ier = hw_p->emac_ier | EMAC_ISR_SYE;
 
@@ -767,8 +781,6 @@ static int ppc_440x_eth_init (struct eth_device *dev, bd_t * bis)
 		/*
 		 * Connect interrupt service routines
 		 */
-		irq_install_handler (VECNUM_EWU0 + (hw_p->devnum * 2),
-				     (interrupt_handler_t *) enetInt, dev);
 		irq_install_handler (VECNUM_ETH0 + (hw_p->devnum * 2),
 				     (interrupt_handler_t *) enetInt, dev);
 	}
@@ -782,13 +794,13 @@ static int ppc_440x_eth_init (struct eth_device *dev, bd_t * bis)
 }
 
 
-static int ppc_440x_eth_send (struct eth_device *dev, volatile void *ptr,
+static int ppc_4xx_eth_send (struct eth_device *dev, volatile void *ptr,
 			      int len)
 {
 	struct enet_frame *ef_ptr;
 	ulong time_start, time_now;
 	unsigned long temp_txm0;
-	EMAC_440GX_HW_PST hw_p = dev->priv;
+	EMAC_4XX_HW_PST hw_p = dev->priv;
 
 	ef_ptr = (struct enet_frame *) ptr;
 
@@ -823,7 +835,7 @@ static int ppc_440x_eth_send (struct eth_device *dev, volatile void *ptr,
 
 	out32 (EMAC_TXM0 + hw_p->hw_addr,
 	       in32 (EMAC_TXM0 + hw_p->hw_addr) | EMAC_TXM0_GNP0);
-#ifdef INFO_440_ENET
+#ifdef INFO_4XX_ENET
 	hw_p->stats.pkts_tx++;
 #endif
 
@@ -849,6 +861,7 @@ static int ppc_440x_eth_send (struct eth_device *dev, volatile void *ptr,
 	}
 }
 
+#if defined (CONFIG_440)
 
 int enetInt (struct eth_device *dev)
 {
@@ -862,13 +875,17 @@ int enetInt (struct eth_device *dev)
 #if defined(CONFIG_440GX)
 	unsigned long my_uic2msr;
 #endif
-	EMAC_440GX_HW_PST hw_p;
+	EMAC_4XX_HW_PST hw_p;
 
 	/*
 	 * Because the mal is generic, we need to get the current
 	 * eth device
 	 */
-	dev = eth_get_dev ();
+#if defined(CONFIG_NET_MULTI)
+	dev = eth_get_dev();
+#else
+	dev = emac0_dev;
+#endif
 
 	hw_p = dev->priv;
 
@@ -1026,6 +1043,96 @@ int enetInt (struct eth_device *dev)
 	return (rc);
 }
 
+#else /* CONFIG_440 */
+
+int enetInt (struct eth_device *dev)
+{
+	int serviced;
+	int rc = -1;		/* default to not us */
+	unsigned long mal_isr;
+	unsigned long emac_isr = 0;
+	unsigned long mal_rx_eob;
+	unsigned long my_uicmsr;
+
+	EMAC_4XX_HW_PST hw_p;
+
+	/*
+	 * Because the mal is generic, we need to get the current
+	 * eth device
+	 */
+#if defined(CONFIG_NET_MULTI)
+	dev = eth_get_dev();
+#else
+	dev = emac0_dev;
+#endif
+
+	hw_p = dev->priv;
+
+	/* enter loop that stays in interrupt code until nothing to service */
+	do {
+		serviced = 0;
+
+		my_uicmsr = mfdcr (uicmsr);
+
+		if ((my_uicmsr & (MAL_UIC_DEF | EMAC_UIC_DEF)) == 0) {	/* not for us */
+			return (rc);
+		}
+		/* get and clear controller status interrupts */
+		/* look at Mal and EMAC interrupts */
+		if ((MAL_UIC_DEF & my_uicmsr) != 0) {	/* we have a MAL interrupt */
+			mal_isr = mfdcr (malesr);
+			/* look for mal error */
+			if ((my_uicmsr & MAL_UIC_ERR) != 0) {
+				mal_err (dev, mal_isr, my_uicmsr, MAL_UIC_DEF, MAL_UIC_ERR);
+				serviced = 1;
+				rc = 0;
+			}
+		}
+
+		/* port by port dispatch of emac interrupts */
+
+		if ((SEL_UIC_DEF(hw_p->devnum) & my_uicmsr) != 0) {	/* look for EMAC errors */
+			emac_isr = in32 (EMAC_ISR + hw_p->hw_addr);
+			if ((hw_p->emac_ier & emac_isr) != 0) {
+				emac_err (dev, emac_isr);
+				serviced = 1;
+				rc = 0;
+			}
+		}
+		if (((hw_p->emac_ier & emac_isr) != 0) || ((MAL_UIC_ERR & my_uicmsr) != 0)) {
+			mtdcr (uicsr, MAL_UIC_DEF | SEL_UIC_DEF(hw_p->devnum)); /* Clear */
+			return (rc);		/* we had errors so get out */
+		}
+
+		/* handle MAX TX EOB interrupt from a tx */
+		if (my_uicmsr & UIC_MAL_TXEOB) {
+			mal_rx_eob = mfdcr (maltxeobisr);
+			mtdcr (maltxeobisr, mal_rx_eob);
+			mtdcr (uicsr, UIC_MAL_TXEOB);
+		}
+		/* handle MAL RX EOB  interupt from a receive */
+		/* check for EOB on valid channels	      */
+		if (my_uicmsr & UIC_MAL_RXEOB)
+		{
+			mal_rx_eob = mfdcr (malrxeobisr);
+			if ((mal_rx_eob & (0x80000000 >> hw_p->devnum)) != 0) {	/* call emac routine for channel x */
+				/* clear EOB
+				 mtdcr(malrxeobisr, mal_rx_eob); */
+				enet_rcv (dev, emac_isr);
+				/* indicate that we serviced an interrupt */
+				serviced = 1;
+				rc = 0;
+			}
+		}
+		mtdcr (uicsr, MAL_UIC_DEF|EMAC_UIC_DEF|EMAC_UIC_DEF1);	/* Clear */
+	}
+	while (serviced);
+
+	return (rc);
+}
+
+#endif /* CONFIG_440 */
+
 /*-----------------------------------------------------------------------------+
  *  MAL Error Routine
  *-----------------------------------------------------------------------------*/
@@ -1033,7 +1140,7 @@ static void mal_err (struct eth_device *dev, unsigned long isr,
 		     unsigned long uic, unsigned long maldef,
 		     unsigned long mal_errr)
 {
-	EMAC_440GX_HW_PST hw_p = dev->priv;
+	EMAC_4XX_HW_PST hw_p = dev->priv;
 
 	mtdcr (malesr, isr);	/* clear interrupt */
 
@@ -1041,7 +1148,7 @@ static void mal_err (struct eth_device *dev, unsigned long isr,
 	mtdcr (maltxdeir, 0xC0000000);
 	mtdcr (malrxdeir, 0x80000000);
 
-#ifdef INFO_440_ENET
+#ifdef INFO_4XX_ENET
 	printf ("\nMAL error occured.... ISR = %lx UIC = = %lx  MAL_DEF = %lx  MAL_ERR= %lx \n", isr, uic, maldef, mal_errr);
 #endif
 
@@ -1053,7 +1160,7 @@ static void mal_err (struct eth_device *dev, unsigned long isr,
  *-----------------------------------------------------------------------------*/
 static void emac_err (struct eth_device *dev, unsigned long isr)
 {
-	EMAC_440GX_HW_PST hw_p = dev->priv;
+	EMAC_4XX_HW_PST hw_p = dev->priv;
 
 	printf ("EMAC%d error occured.... ISR = %lx\n", hw_p->devnum, isr);
 	out32 (EMAC_ISR + hw_p->hw_addr, isr);
@@ -1067,7 +1174,7 @@ static void enet_rcv (struct eth_device *dev, unsigned long malisr)
 	struct enet_frame *ef_ptr;
 	unsigned long data_len;
 	unsigned long rx_eob_isr;
-	EMAC_440GX_HW_PST hw_p = dev->priv;
+	EMAC_4XX_HW_PST hw_p = dev->priv;
 
 	int handled = 0;
 	int i;
@@ -1127,7 +1234,7 @@ static void enet_rcv (struct eth_device *dev, unsigned long malisr)
 				hw_p->stats.rx += data_len;
 				ef_ptr = (struct enet_frame *) hw_p->rx[i].
 					data_ptr;
-#ifdef INFO_440_ENET
+#ifdef INFO_4XX_ENET
 				hw_p->stats.pkts_rx++;
 #endif
 				/* AS.HARNOIS
@@ -1138,8 +1245,6 @@ static void enet_rcv (struct eth_device *dev, unsigned long malisr)
 				if (NUM_RX_BUFF == hw_p->rx_i_index)
 					hw_p->rx_i_index = 0;
 
-				/* printf("X");  /|* test-only *|/ */
-
 				/*  AS.HARNOIS
 				 * free receive buffer only when
 				 * buffer has been handled (eth_rx)
@@ -1151,12 +1256,12 @@ static void enet_rcv (struct eth_device *dev, unsigned long malisr)
 }
 
 
-static int ppc_440x_eth_rx (struct eth_device *dev)
+static int ppc_4xx_eth_rx (struct eth_device *dev)
 {
 	int length;
 	int user_index;
 	unsigned long msr;
-	EMAC_440GX_HW_PST hw_p = dev->priv;
+	EMAC_4XX_HW_PST hw_p = dev->priv;
 
 	hw_p->is_receiving = 1;	/* tell driver */
 
@@ -1188,7 +1293,7 @@ static int ppc_440x_eth_rx (struct eth_device *dev)
 		if (NUM_RX_BUFF == hw_p->rx_u_index)
 			hw_p->rx_u_index = 0;
 
-#ifdef INFO_440_ENET
+#ifdef INFO_4XX_ENET
 		hw_p->stats.pkts_handled++;
 #endif
 
@@ -1200,12 +1305,12 @@ static int ppc_440x_eth_rx (struct eth_device *dev)
 	return length;
 }
 
-int ppc_440x_eth_initialize (bd_t * bis)
+int ppc_4xx_eth_initialize (bd_t * bis)
 {
 	static int virgin = 0;
 	struct eth_device *dev;
 	int eth_num = 0;
-	EMAC_440GX_HW_PST hw = NULL;
+	EMAC_4XX_HW_PST hw = NULL;
 
 #if defined(CONFIG_440GX)
 	unsigned long pfc1;
@@ -1229,7 +1334,7 @@ int ppc_440x_eth_initialize (bd_t * bis)
 	bis->bi_phymode[3] = 2;
 
 #if defined (CONFIG_440GX)
-	ppc_440x_eth_setup_bridge(0, bis);
+	ppc_4xx_eth_setup_bridge(0, bis);
 #endif
 #endif
 
@@ -1273,16 +1378,16 @@ int ppc_440x_eth_initialize (bd_t * bis)
 		/* Allocate device structure */
 		dev = (struct eth_device *) malloc (sizeof (*dev));
 		if (dev == NULL) {
-			printf ("ppc_440x_eth_initialize: "
+			printf ("ppc_4xx_eth_initialize: "
 				"Cannot allocate eth_device %d\n", eth_num);
 			return (-1);
 		}
 		memset(dev, 0, sizeof(*dev));
 
 		/* Allocate our private use data */
-		hw = (EMAC_440GX_HW_PST) malloc (sizeof (*hw));
+		hw = (EMAC_4XX_HW_PST) malloc (sizeof (*hw));
 		if (hw == NULL) {
-			printf ("ppc_440x_eth_initialize: "
+			printf ("ppc_4xx_eth_initialize: "
 				"Cannot allocate private hw data for eth_device %d",
 				eth_num);
 			free (dev);
@@ -1319,12 +1424,12 @@ int ppc_440x_eth_initialize (bd_t * bis)
 		hw->devnum = eth_num;
 		hw->print_speed = 1;
 
-		sprintf (dev->name, "ppc_440x_eth%d", eth_num);
+		sprintf (dev->name, "ppc_4xx_eth%d", eth_num);
 		dev->priv = (void *) hw;
-		dev->init = ppc_440x_eth_init;
-		dev->halt = ppc_440x_eth_halt;
-		dev->send = ppc_440x_eth_send;
-		dev->recv = ppc_440x_eth_rx;
+		dev->init = ppc_4xx_eth_init;
+		dev->halt = ppc_4xx_eth_halt;
+		dev->send = ppc_4xx_eth_send;
+		dev->recv = ppc_4xx_eth_rx;
 
 		if (0 == virgin) {
 			/* set the MAL IER ??? names may change with new spec ??? */
@@ -1355,9 +1460,42 @@ int ppc_440x_eth_initialize (bd_t * bis)
 			virgin = 1;
 		}
 
+#if defined(CONFIG_NET_MULTI)
 		eth_register (dev);
+#else
+		emac0_dev = dev;
+#endif
 
 	}			/* end for each supported device */
 	return (1);
 }
-#endif /* CONFIG_440 && CONFIG_NET_MULTI */
+
+
+#if !defined(CONFIG_NET_MULTI)
+void eth_halt (void) {
+	if (emac0_dev) {
+		ppc_4xx_eth_halt(emac0_dev);
+		free(emac0_dev);
+		emac0_dev = NULL;
+	}
+}
+
+int eth_init (bd_t *bis)
+{
+	ppc_4xx_eth_initialize(bis);
+	return(ppc_4xx_eth_init(emac0_dev, bis));
+}
+
+int eth_send(volatile void *packet, int length)
+{
+
+	return (ppc_4xx_eth_send(emac0_dev, packet, length));
+}
+
+int eth_rx(void)
+{
+	return (ppc_4xx_eth_rx(emac0_dev));
+}
+#endif /* !defined(CONFIG_NET_MULTI) */
+
+#endif /* #if (CONFIG_COMMANDS & CFG_CMD_NET) */
diff --git a/cpu/ppc4xx/Makefile b/cpu/ppc4xx/Makefile
index 5b16754c50..c563457005 100644
--- a/cpu/ppc4xx/Makefile
+++ b/cpu/ppc4xx/Makefile
@@ -27,10 +27,10 @@ LIB	= lib$(CPU).a
 
 START	= start.o resetvec.o kgdb.o
 AOBJS	= dcr.o
-COBJS	= 405gp_enet.o 405gp_pci.o 440gx_enet.o \
+COBJS	= 405gp_pci.o 4xx_enet.o \
 	  bedbug_405.o commproc.o \
 	  cpu.o cpu_init.o i2c.o interrupts.o \
-	  miiphy.o miiphy_440.o sdram.o serial.o \
+	  miiphy.o sdram.o serial.o \
 	  spd_sdram.o speed.o traps.o usb_ohci.o usbdev.o
 
 OBJS	= $(AOBJS) $(COBJS)
diff --git a/cpu/ppc4xx/cpu_init.c b/cpu/ppc4xx/cpu_init.c
index 68e1a450ca..79cfba3a45 100644
--- a/cpu/ppc4xx/cpu_init.c
+++ b/cpu/ppc4xx/cpu_init.c
@@ -23,7 +23,7 @@
 
 #include <common.h>
 #include <watchdog.h>
-#include <405gp_enet.h>
+#include <ppc4xx_enet.h>
 #include <asm/processor.h>
 #include <ppc4xx.h>
 
diff --git a/cpu/ppc4xx/miiphy.c b/cpu/ppc4xx/miiphy.c
index cb9dccdc35..24f91546c6 100644
--- a/cpu/ppc4xx/miiphy.c
+++ b/cpu/ppc4xx/miiphy.c
@@ -1,42 +1,44 @@
 /*-----------------------------------------------------------------------------+
   |
-  |       This source code has been made available to you by IBM on an AS-IS
-  |       basis.  Anyone receiving this source is licensed under IBM
-  |       copyrights to use it in any way he or she deems fit, including
-  |       copying it, modifying it, compiling it, and redistributing it either
-  |       with or without modifications.  No license under IBM patents or
-  |       patent applications is to be implied by the copyright license.
+  |	  This source code has been made available to you by IBM on an AS-IS
+  |	  basis.  Anyone receiving this source is licensed under IBM
+  |	  copyrights to use it in any way he or she deems fit, including
+  |	  copying it, modifying it, compiling it, and redistributing it either
+  |	  with or without modifications.  No license under IBM patents or
+  |	  patent applications is to be implied by the copyright license.
   |
-  |       Any user of this software should understand that IBM cannot provide
-  |       technical support for this software and will not be responsible for
-  |       any consequences resulting from the use of this software.
+  |	  Any user of this software should understand that IBM cannot provide
+  |	  technical support for this software and will not be responsible for
+  |	  any consequences resulting from the use of this software.
   |
-  |       Any person who transfers this source code or any derivative work
-  |       must include the IBM copyright notice, this paragraph, and the
-  |       preceding two paragraphs in the transferred software.
+  |	  Any person who transfers this source code or any derivative work
+  |	  must include the IBM copyright notice, this paragraph, and the
+  |	  preceding two paragraphs in the transferred software.
   |
-  |       COPYRIGHT   I B M   CORPORATION 1995
-  |       LICENSED MATERIAL  -  PROGRAM PROPERTY OF I B M
+  |	  COPYRIGHT   I B M   CORPORATION 1995
+  |	  LICENSED MATERIAL  -	PROGRAM PROPERTY OF I B M
   +-----------------------------------------------------------------------------*/
 /*-----------------------------------------------------------------------------+
   |
-  |  File Name:  miiphy.c
+  |  File Name:	 miiphy.c
   |
-  |  Function:   This module has utilities for accessing the MII PHY through
+  |  Function:	 This module has utilities for accessing the MII PHY through
   |	       the EMAC3 macro.
   |
-  |  Author:     Mark Wisner
+  |  Author:	 Mark Wisner
   |
   |  Change Activity-
   |
-  |  Date        Description of Change                                       BY
-  |  ---------   ---------------------                                       ---
-  |  05-May-99   Created                                                     MKW
-  |  01-Jul-99   Changed clock setting of sta_reg from 66Mhz to 50Mhz to
-  |              better match OPB speed. Also modified delay times.      	   JWB
-  |  29-Jul-99   Added Full duplex support                                   MKW
-  |  24-Aug-99   Removed printf from dp83843_duplex()                      JWB
-  |  19-Jul-00   Ported to esd cpci405                                       sr
+  |  Date	 Description of Change					     BY
+  |  ---------	 ---------------------					     ---
+  |  05-May-99	 Created						     MKW
+  |  01-Jul-99	 Changed clock setting of sta_reg from 66Mhz to 50Mhz to
+  |		 better match OPB speed. Also modified delay times.	     JWB
+  |  29-Jul-99	 Added Full duplex support				     MKW
+  |  24-Aug-99	 Removed printf from dp83843_duplex()			     JWB
+  |  19-Jul-00	 Ported to esd cpci405					     sr
+  |  23-Dec-03	 Ported from miiphy.c to 440GX Travis Sawyer		     TBS
+  |		 <travis.sawyer@sandburst.com>
   |
   +-----------------------------------------------------------------------------*/
 
@@ -44,15 +46,13 @@
 #include <asm/processor.h>
 #include <ppc_asm.tmpl>
 #include <commproc.h>
-#include <405gp_enet.h>
+#include <ppc4xx_enet.h>
 #include <405_mal.h>
 #include <miiphy.h>
 
-#if defined(CONFIG_405GP) || defined(CONFIG_405EP) || \
-  (defined(CONFIG_440) && !defined(CONFIG_NET_MULTI))
 
 /***********************************************************/
-/* Dump out to the screen PHY regs                         */
+/* Dump out to the screen PHY regs			   */
 /***********************************************************/
 
 void miiphy_dump (unsigned char addr)
@@ -72,75 +72,127 @@ void miiphy_dump (unsigned char addr)
 		if (i == 0x07)
 			i = 0x0f;
 
-	} /* end for loop */
-} /* end dump */
+	}			/* end for loop */
+}				/* end dump */
 
 
 /***********************************************************/
-/* read a phy reg and return the value with a rc           */
-/* Note: We are referencing to EMAC_STACR register         */
-/* @(EMAC_BASE + 92) because  of:                          */
-/* - 405EP has only STACR for EMAC0 pinned out             */
-/* - 405GP has onle one EMAC0                              */
-/* - For 440 this module gets compiled only for            */
-/*   !CONFIG_NET_MULTI, i.e. only EMAC0 is supported.      */
+/* (Re)start autonegotiation				   */
 /***********************************************************/
+int phy_setup_aneg (unsigned char addr)
+{
+	unsigned short ctl, adv;
+
+	/* Setup standard advertise */
+	miiphy_read (addr, PHY_ANAR, &adv);
+	adv |= (PHY_ANLPAR_ACK | PHY_ANLPAR_RF | PHY_ANLPAR_T4 |
+		PHY_ANLPAR_TXFD | PHY_ANLPAR_TX | PHY_ANLPAR_10FD |
+		PHY_ANLPAR_10);
+	miiphy_write (addr, PHY_ANAR, adv);
 
-int miiphy_read (unsigned char addr, unsigned char reg,
-				 unsigned short *value)
+	/* Start/Restart aneg */
+	miiphy_read (addr, PHY_BMCR, &ctl);
+	ctl |= (PHY_BMCR_AUTON | PHY_BMCR_RST_NEG);
+	miiphy_write (addr, PHY_BMCR, ctl);
+
+	return 0;
+}
+
+
+/***********************************************************/
+/* read a phy reg and return the value with a rc	   */
+/***********************************************************/
+unsigned int miiphy_getemac_offset (void)
 {
-	unsigned long sta_reg;		/* STA scratch area */
+#if defined(CONFIG_440) && defined(CONFIG_NET_MULTI)
+	unsigned long zmii;
+	unsigned long eoffset;
+
+	/* Need to find out which mdi port we're using */
+	zmii = in32 (ZMII_FER);
+
+	if (zmii & (ZMII_FER_MDI << ZMII_FER_V (0))) {
+		/* using port 0 */
+		eoffset = 0;
+	} else if (zmii & (ZMII_FER_MDI << ZMII_FER_V (1))) {
+		/* using port 1 */
+		eoffset = 0x100;
+	} else if (zmii & (ZMII_FER_MDI << ZMII_FER_V (2))) {
+		/* using port 2 */
+		eoffset = 0x400;
+	} else if (zmii & (ZMII_FER_MDI << ZMII_FER_V (3))) {
+		/* using port 3 */
+		eoffset = 0x600;
+	} else {
+		/* None of the mdi ports are enabled! */
+		/* enable port 0 */
+		zmii |= ZMII_FER_MDI << ZMII_FER_V (0);
+		out32 (ZMII_FER, zmii);
+		eoffset = 0;
+		/* need to soft reset port 0 */
+		zmii = in32 (EMAC_M0);
+		zmii |= EMAC_M0_SRST;
+		out32 (EMAC_M0, zmii);
+	}
+
+	return (eoffset);
+#else
+	return 0;
+#endif
+}
+
+
+int miiphy_read (unsigned char addr, unsigned char reg, unsigned short *value)
+{
+	unsigned long sta_reg;	/* STA scratch area */
 	unsigned long i;
+	unsigned long emac_reg;
+
 
+	emac_reg = miiphy_getemac_offset ();
 	/* see if it is ready for 1000 nsec */
 	i = 0;
 
 	/* see if it is ready for  sec */
-	while ((in32 (EMAC_STACR) & EMAC_STACR_OC) == 0) {
+	while ((in32 (EMAC_STACR + emac_reg) & EMAC_STACR_OC) == 0) {
 		udelay (7);
 		if (i > 5) {
-#if 0	/* test-only */
+#if 0
 			printf ("read err 1\n");
 #endif
 			return -1;
 		}
 		i++;
 	}
-	sta_reg = reg;				/* reg address */
+	sta_reg = reg;		/* reg address */
 	/* set clock (50Mhz) and read flags */
+#if defined(CONFIG_440GX)
+	sta_reg |= EMAC_STACR_READ;
+#else
 	sta_reg = (sta_reg | EMAC_STACR_READ) & ~EMAC_STACR_CLK_100MHZ;
-#ifdef CONFIG_PHY_CLK_FREQ
+#endif
+
+#if defined(CONFIG_PHY_CLK_FREQ) && !defined(CONFIG_440GX)
 	sta_reg = sta_reg | CONFIG_PHY_CLK_FREQ;
 #endif
 	sta_reg = sta_reg | (addr << 5);	/* Phy address */
 
-	out32 (EMAC_STACR, sta_reg);
-#if 0	/* test-only */
+	out32 (EMAC_STACR + emac_reg, sta_reg);
+#if 0				/* test-only */
 	printf ("a2: write: EMAC_STACR=0x%0x\n", sta_reg);	/* test-only */
 #endif
 
-#ifdef CONFIG_PHY_CMD_DELAY
-	udelay (CONFIG_PHY_CMD_DELAY);		/* Intel LXT971A needs this */
-#endif
-	sta_reg = in32 (EMAC_STACR);
+	sta_reg = in32 (EMAC_STACR + emac_reg);
 	i = 0;
 	while ((sta_reg & EMAC_STACR_OC) == 0) {
 		udelay (7);
 		if (i > 5) {
-#if 0	/* test-only */
-			printf ("read err 2\n");
-#endif
 			return -1;
 		}
 		i++;
-		sta_reg = in32 (EMAC_STACR);
+		sta_reg = in32 (EMAC_STACR + emac_reg);
 	}
 	if ((sta_reg & EMAC_STACR_PHYE) != 0) {
-#if 0	/* test-only */
-		printf ("read err 3\n");
-		printf ("a2: read: EMAC_STACR=0x%0lx, i=%d\n",
-			sta_reg, (int) i);	/* test-only */
-#endif
 		return -1;
 	}
 
@@ -148,58 +200,59 @@ int miiphy_read (unsigned char addr, unsigned char reg,
 	return 0;
 
 
-} /* phy_read */
+}				/* phy_read */
 
 
 /***********************************************************/
-/* write a phy reg and return the value with a rc           */
+/* write a phy reg and return the value with a rc	    */
 /***********************************************************/
 
-int miiphy_write (unsigned char addr, unsigned char reg,
-		  unsigned short value)
+int miiphy_write (unsigned char addr, unsigned char reg, unsigned short value)
 {
-	unsigned long sta_reg;		/* STA scratch area */
+	unsigned long sta_reg;	/* STA scratch area */
 	unsigned long i;
+	unsigned long emac_reg;
 
+	emac_reg = miiphy_getemac_offset ();
 	/* see if it is ready for 1000 nsec */
 	i = 0;
 
-	while ((in32 (EMAC_STACR) & EMAC_STACR_OC) == 0) {
+	while ((in32 (EMAC_STACR + emac_reg) & EMAC_STACR_OC) == 0) {
 		if (i > 5)
 			return -1;
 		udelay (7);
 		i++;
 	}
 	sta_reg = 0;
-	sta_reg = reg;				/* reg address */
+	sta_reg = reg;		/* reg address */
 	/* set clock (50Mhz) and read flags */
+#if defined(CONFIG_440GX)
+	sta_reg |= EMAC_STACR_WRITE;
+#else
 	sta_reg = (sta_reg | EMAC_STACR_WRITE) & ~EMAC_STACR_CLK_100MHZ;
-#ifdef CONFIG_PHY_CLK_FREQ
-	sta_reg = sta_reg | CONFIG_PHY_CLK_FREQ; /* Set clock frequency (PLB freq. dependend) */
+#endif
+
+#if defined(CONFIG_PHY_CLK_FREQ) && !defined(CONFIG_440GX)
+	sta_reg = sta_reg | CONFIG_PHY_CLK_FREQ;	/* Set clock frequency (PLB freq. dependend) */
 #endif
 	sta_reg = sta_reg | ((unsigned long) addr << 5);	/* Phy address */
 	memcpy (&sta_reg, &value, 2);	/* put in data */
 
-	out32 (EMAC_STACR, sta_reg);
+	out32 (EMAC_STACR + emac_reg, sta_reg);
 
-#ifdef CONFIG_PHY_CMD_DELAY
-	udelay (CONFIG_PHY_CMD_DELAY);		/* Intel LXT971A needs this */
-#endif
 	/* wait for completion */
 	i = 0;
-	sta_reg = in32 (EMAC_STACR);
+	sta_reg = in32 (EMAC_STACR + emac_reg);
 	while ((sta_reg & EMAC_STACR_OC) == 0) {
 		udelay (7);
 		if (i > 5)
 			return -1;
 		i++;
-		sta_reg = in32 (EMAC_STACR);
+		sta_reg = in32 (EMAC_STACR + emac_reg);
 	}
 
 	if ((sta_reg & EMAC_STACR_PHYE) != 0)
 		return -1;
 	return 0;
 
-} /* phy_read */
-
-#endif	/* CONFIG_405GP */
+}				/* phy_write */
diff --git a/cpu/ppc4xx/miiphy_440.c b/cpu/ppc4xx/miiphy_440.c
deleted file mode 100644
index 6320feaba7..0000000000
--- a/cpu/ppc4xx/miiphy_440.c
+++ /dev/null
@@ -1,259 +0,0 @@
-/*-----------------------------------------------------------------------------+
-  |
-  |	  This source code has been made available to you by IBM on an AS-IS
-  |	  basis.  Anyone receiving this source is licensed under IBM
-  |	  copyrights to use it in any way he or she deems fit, including
-  |	  copying it, modifying it, compiling it, and redistributing it either
-  |	  with or without modifications.  No license under IBM patents or
-  |	  patent applications is to be implied by the copyright license.
-  |
-  |	  Any user of this software should understand that IBM cannot provide
-  |	  technical support for this software and will not be responsible for
-  |	  any consequences resulting from the use of this software.
-  |
-  |	  Any person who transfers this source code or any derivative work
-  |	  must include the IBM copyright notice, this paragraph, and the
-  |	  preceding two paragraphs in the transferred software.
-  |
-  |	  COPYRIGHT   I B M   CORPORATION 1995
-  |	  LICENSED MATERIAL  -	PROGRAM PROPERTY OF I B M
-  +-----------------------------------------------------------------------------*/
-/*-----------------------------------------------------------------------------+
-  |
-  |  File Name:	 miiphy.c
-  |
-  |  Function:	 This module has utilities for accessing the MII PHY through
-  |	       the EMAC3 macro.
-  |
-  |  Author:	 Mark Wisner
-  |
-  |  Change Activity-
-  |
-  |  Date	 Description of Change					     BY
-  |  ---------	 ---------------------					     ---
-  |  05-May-99	 Created						     MKW
-  |  01-Jul-99	 Changed clock setting of sta_reg from 66Mhz to 50Mhz to
-  |		 better match OPB speed. Also modified delay times.	     JWB
-  |  29-Jul-99	 Added Full duplex support				     MKW
-  |  24-Aug-99	 Removed printf from dp83843_duplex()			     JWB
-  |  19-Jul-00	 Ported to esd cpci405					     sr
-  |  23-Dec-03	 Ported from miiphy.c to 440GX Travis Sawyer		     TBS
-  |		 <travis.sawyer@sandburst.com>
-  |
-  +-----------------------------------------------------------------------------*/
-
-#include <common.h>
-#include <asm/processor.h>
-#include <ppc_asm.tmpl>
-#include <commproc.h>
-#include <440gx_enet.h>
-#include <405_mal.h>
-#include <miiphy.h>
-
-#if defined(CONFIG_440) && defined(CONFIG_NET_MULTI)
-
-
-/***********************************************************/
-/* Dump out to the screen PHY regs			   */
-/***********************************************************/
-
-void miiphy_dump (unsigned char addr)
-{
-	unsigned long i;
-	unsigned short data;
-
-
-	for (i = 0; i < 0x1A; i++) {
-		if (miiphy_read (addr, i, &data)) {
-			printf ("read error for reg %lx\n", i);
-			return;
-		}
-		printf ("Phy reg %lx ==> %4x\n", i, data);
-
-		/* jump to the next set of regs */
-		if (i == 0x07)
-			i = 0x0f;
-
-	}			/* end for loop */
-}				/* end dump */
-
-
-/***********************************************************/
-/* (Re)start autonegotiation				   */
-/***********************************************************/
-int phy_setup_aneg (unsigned char addr)
-{
-	unsigned short ctl, adv;
-
-	/* Setup standard advertise */
-	miiphy_read (addr, PHY_ANAR, &adv);
-	adv |= (PHY_ANLPAR_ACK | PHY_ANLPAR_RF | PHY_ANLPAR_T4 |
-		PHY_ANLPAR_TXFD | PHY_ANLPAR_TX | PHY_ANLPAR_10FD |
-		PHY_ANLPAR_10);
-	miiphy_write (addr, PHY_ANAR, adv);
-
-	/* Start/Restart aneg */
-	miiphy_read (addr, PHY_BMCR, &ctl);
-	ctl |= (PHY_BMCR_AUTON | PHY_BMCR_RST_NEG);
-	miiphy_write (addr, PHY_BMCR, ctl);
-
-	return 0;
-}
-
-
-/***********************************************************/
-/* read a phy reg and return the value with a rc	   */
-/***********************************************************/
-unsigned int miiphy_getemac_offset (void)
-{
-	unsigned long zmii;
-	unsigned long eoffset;
-
-	/* Need to find out which mdi port we're using */
-	zmii = in32 (ZMII_FER);
-
-	if (zmii & (ZMII_FER_MDI << ZMII_FER_V (0))) {
-		/* using port 0 */
-		eoffset = 0;
-	} else if (zmii & (ZMII_FER_MDI << ZMII_FER_V (1))) {
-		/* using port 1 */
-		eoffset = 0x100;
-	} else if (zmii & (ZMII_FER_MDI << ZMII_FER_V (2))) {
-		/* using port 2 */
-		eoffset = 0x400;
-	} else if (zmii & (ZMII_FER_MDI << ZMII_FER_V (3))) {
-		/* using port 3 */
-		eoffset = 0x600;
-	} else {
-		/* None of the mdi ports are enabled! */
-		/* enable port 0 */
-		zmii |= ZMII_FER_MDI << ZMII_FER_V (0);
-		out32 (ZMII_FER, zmii);
-		eoffset = 0;
-		/* need to soft reset port 0 */
-		zmii = in32 (EMAC_M0);
-		zmii |= EMAC_M0_SRST;
-		out32 (EMAC_M0, zmii);
-	}
-
-	return (eoffset);
-
-}
-
-
-int miiphy_read (unsigned char addr, unsigned char reg, unsigned short *value)
-{
-	unsigned long sta_reg;	/* STA scratch area */
-	unsigned long i;
-	unsigned long emac_reg;
-
-
-	emac_reg = miiphy_getemac_offset ();
-	/* see if it is ready for 1000 nsec */
-	i = 0;
-
-	/* see if it is ready for  sec */
-	while ((in32 (EMAC_STACR + emac_reg) & EMAC_STACR_OC) == 0) {
-		udelay (7);
-		if (i > 5) {
-#if 0
-			printf ("read err 1\n");
-#endif
-			return -1;
-		}
-		i++;
-	}
-	sta_reg = reg;		/* reg address */
-	/* set clock (50Mhz) and read flags */
-#if defined(CONFIG_440GX)
-	sta_reg |= EMAC_STACR_READ;
-#else
-	sta_reg = (sta_reg | EMAC_STACR_READ) & ~EMAC_STACR_CLK_100MHZ;
-#endif
-
-#if defined(CONFIG_PHY_CLK_FREQ) && !defined(CONFIG_440GX)
-	sta_reg = sta_reg | CONFIG_PHY_CLK_FREQ;
-#endif
-	sta_reg = sta_reg | (addr << 5);	/* Phy address */
-
-	out32 (EMAC_STACR + emac_reg, sta_reg);
-#if 0				/* test-only */
-	printf ("a2: write: EMAC_STACR=0x%0x\n", sta_reg);	/* test-only */
-#endif
-
-	sta_reg = in32 (EMAC_STACR + emac_reg);
-	i = 0;
-	while ((sta_reg & EMAC_STACR_OC) == 0) {
-		udelay (7);
-		if (i > 5) {
-			return -1;
-		}
-		i++;
-		sta_reg = in32 (EMAC_STACR + emac_reg);
-	}
-	if ((sta_reg & EMAC_STACR_PHYE) != 0) {
-		return -1;
-	}
-
-	*value = *(short *) (&sta_reg);
-	return 0;
-
-
-}				/* phy_read */
-
-
-/***********************************************************/
-/* write a phy reg and return the value with a rc	    */
-/***********************************************************/
-
-int miiphy_write (unsigned char addr, unsigned char reg, unsigned short value)
-{
-	unsigned long sta_reg;	/* STA scratch area */
-	unsigned long i;
-	unsigned long emac_reg;
-
-	emac_reg = miiphy_getemac_offset ();
-	/* see if it is ready for 1000 nsec */
-	i = 0;
-
-	while ((in32 (EMAC_STACR + emac_reg) & EMAC_STACR_OC) == 0) {
-		if (i > 5)
-			return -1;
-		udelay (7);
-		i++;
-	}
-	sta_reg = 0;
-	sta_reg = reg;		/* reg address */
-	/* set clock (50Mhz) and read flags */
-#if defined(CONFIG_440GX)
-	sta_reg |= EMAC_STACR_WRITE;
-#else
-	sta_reg = (sta_reg | EMAC_STACR_WRITE) & ~EMAC_STACR_CLK_100MHZ;
-#endif
-
-#if defined(CONFIG_PHY_CLK_FREQ) && !defined(CONFIG_440GX)
-	sta_reg = sta_reg | CONFIG_PHY_CLK_FREQ;	/* Set clock frequency (PLB freq. dependend) */
-#endif
-	sta_reg = sta_reg | ((unsigned long) addr << 5);	/* Phy address */
-	memcpy (&sta_reg, &value, 2);	/* put in data */
-
-	out32 (EMAC_STACR + emac_reg, sta_reg);
-
-	/* wait for completion */
-	i = 0;
-	sta_reg = in32 (EMAC_STACR + emac_reg);
-	while ((sta_reg & EMAC_STACR_OC) == 0) {
-		udelay (7);
-		if (i > 5)
-			return -1;
-		i++;
-		sta_reg = in32 (EMAC_STACR + emac_reg);
-	}
-
-	if ((sta_reg & EMAC_STACR_PHYE) != 0)
-		return -1;
-	return 0;
-
-}				/* phy_write */
-
-#endif /* CONFIG_405GP */
diff --git a/include/405gp_enet.h b/include/405gp_enet.h
deleted file mode 100644
index b9bdaaf7cd..0000000000
--- a/include/405gp_enet.h
+++ /dev/null
@@ -1,305 +0,0 @@
-/*----------------------------------------------------------------------------+
-|
-|       This source code has been made available to you by IBM on an AS-IS
-|       basis.  Anyone receiving this source is licensed under IBM
-|       copyrights to use it in any way he or she deems fit, including
-|       copying it, modifying it, compiling it, and redistributing it either
-|       with or without modifications.  No license under IBM patents or
-|       patent applications is to be implied by the copyright license.
-|
-|       Any user of this software should understand that IBM cannot provide
-|       technical support for this software and will not be responsible for
-|       any consequences resulting from the use of this software.
-|
-|       Any person who transfers this source code or any derivative work
-|       must include the IBM copyright notice, this paragraph, and the
-|       preceding two paragraphs in the transferred software.
-|
-|       COPYRIGHT   I B M   CORPORATION 1999
-|       LICENSED MATERIAL  -  PROGRAM PROPERTY OF I B M
-+----------------------------------------------------------------------------*/
-/*----------------------------------------------------------------------------+
-|
-|  File Name:   enetemac.h
-|
-|  Function:    Header file for the EMAC3 macro on the 405GP.
-|
-|  Author:      Mark Wisner
-|
-|  Change Activity-
-|
-|  Date        Description of Change                                       BY
-|  ---------   ---------------------                                       ---
-|  29-Apr-99   Created                                                     MKW
-|
-+----------------------------------------------------------------------------*/
-#ifndef _enetemac_h_
-#define _enetemac_h_
-#include <net.h>
-#include <405_mal.h>
-
-/*-----------------------------------------------------------------------------+
-| General enternet defines.  802 frames are not supported.
-+-----------------------------------------------------------------------------*/
-#define ENET_ADDR_LENGTH                6
-#define ENET_ARPTYPE                    0x806
-#define ARP_REQUEST                     1
-#define ARP_REPLY                       2
-#define ENET_IPTYPE                     0x800
-#define ARP_CACHE_SIZE                  5
-
-
-struct enet_frame {
-   unsigned char        dest_addr[ENET_ADDR_LENGTH];
-   unsigned char        source_addr[ENET_ADDR_LENGTH];
-   unsigned short       type;
-   unsigned char        enet_data[1];
-};
-
-struct arp_entry {
-   unsigned long        inet_address;
-   unsigned char        mac_address[ENET_ADDR_LENGTH];
-   unsigned long        valid;
-   unsigned long        sec;
-   unsigned long        nsec;
-};
-
-
-			/*Register addresses */
-#if defined(CONFIG_440)
-#if defined(CONFIG_440EP) || defined(CONFIG_440GR)
-#define ZMII_BASE			(CFG_PERIPHERAL_BASE + 0x0D00)
-#else
-#define ZMII_BASE			(CFG_PERIPHERAL_BASE + 0x0780)
-#endif
-#define ZMII_FER			(ZMII_BASE)
-#define ZMII_SSR			(ZMII_BASE + 4)
-#define ZMII_SMIISR			(ZMII_BASE + 8)
-
-#define ZMII_RMII			0x22000000
-#define ZMII_MDI0			0x80000000
-#endif /* CONFIG_440 */
-
-#if defined(CONFIG_440)
-#if defined(CONFIG_440EP) || defined(CONFIG_440GR)
-#define EMAC_BASE			    (CFG_PERIPHERAL_BASE + 0x0E00)
-#else
-#define EMAC_BASE			    (CFG_PERIPHERAL_BASE + 0x0800)
-#endif
-#else
-#define EMAC_BASE 			0xEF600800
-#endif
-
-#define EMAC_M0 			(EMAC_BASE)
-#define EMAC_M1 			(EMAC_BASE + 4)
-#define EMAC_TXM0				(EMAC_BASE + 8)
-#define EMAC_TXM1		 		(EMAC_BASE + 12)
-#define EMAC_RXM		 		(EMAC_BASE + 16)
-#define EMAC_ISR		 		(EMAC_BASE + 20)
-#define EMAC_IER		 		(EMAC_BASE + 24)
-#define EMAC_IAH		 		(EMAC_BASE + 28)
-#define EMAC_IAL		 		(EMAC_BASE + 32)
-#define EMAC_VLAN_TPID_REG 		(EMAC_BASE + 36)
-#define EMAC_VLAN_TCI_REG 		(EMAC_BASE + 40)
-#define EMAC_PAUSE_TIME_REG 		(EMAC_BASE + 44)
-#define EMAC_IND_HASH_1			(EMAC_BASE + 48)
-#define EMAC_IND_HASH_2			(EMAC_BASE + 52)
-#define EMAC_IND_HASH_3			(EMAC_BASE + 56)
-#define EMAC_IND_HASH_4			(EMAC_BASE + 60)
-#define EMAC_GRP_HASH_1			(EMAC_BASE + 64)
-#define EMAC_GRP_HASH_2			(EMAC_BASE + 68)
-#define EMAC_GRP_HASH_3			(EMAC_BASE + 72)
-#define EMAC_GRP_HASH_4			(EMAC_BASE + 76)
-#define EMAC_LST_SRC_LOW		(EMAC_BASE + 80)
-#define EMAC_LST_SRC_HI			(EMAC_BASE + 84)
-#define EMAC_I_FRAME_GAP_REG		(EMAC_BASE + 88)
-#define EMAC_STACR			(EMAC_BASE + 92)
-#define EMAC_TRTR				(EMAC_BASE + 96)
-#define EMAC_RX_HI_LO_WMARK		(EMAC_BASE + 100)
-
-/* bit definitions */
-/* MODE REG 0 */
-#define EMAC_M0_RXI			0x80000000
-#define EMAC_M0_TXI			0x40000000
-#define EMAC_M0_SRST			0x20000000
-#define EMAC_M0_TXE			0x10000000
-#define EMAC_M0_RXE			0x08000000
-#define EMAC_M0_WKE			0x04000000
-
-/* MODE Reg 1 */
-#define EMAC_M1_FDE			0x80000000
-#define EMAC_M1_ILE			0x40000000
-#define EMAC_M1_VLE			0x20000000
-#define EMAC_M1_EIFC			0x10000000
-#define EMAC_M1_APP			0x08000000
-#define EMAC_M1_AEMI			0x02000000
-#define EMAC_M1_IST			0x01000000
-#define EMAC_M1_MF_1000MBPS		0x00800000	/* 0's for 10MBPS */
-#define EMAC_M1_MF_100MBPS		0x00400000
-#define EMAC_M1_RFS_4K			0x00300000	/* ~4k for 512 byte */
-#define EMAC_M1_RFS_2K			0x00200000
-#define EMAC_M1_RFS_1K			0x00100000
-#define EMAC_M1_TX_FIFO_2K		0x00080000	/* 0's for 512 byte */
-#define EMAC_M1_TX_FIFO_1K		0x00040000
-#define EMAC_M1_TR0_DEPEND		0x00010000	/* 0'x for single packet */
-#define EMAC_M1_TR0_MULTI		0x00008000
-#define EMAC_M1_TR1_DEPEND		0x00004000
-#define EMAC_M1_TR1_MULTI		0x00002000
-#define EMAC_M1_JUMBO_ENABLE		0x00001000
-
-/* Transmit Mode Register 0 */
-#define EMAC_TXM0_GNP0			0x80000000
-#define EMAC_TXM0_GNP1			0x40000000
-#define EMAC_TXM0_GNPD			0x20000000
-#define EMAC_TXM0_FC			0x10000000
-
-/* Receive Mode Register */
-#define EMAC_RMR_SP			0x80000000
-#define EMAC_RMR_SFCS			0x40000000
-#define EMAC_RMR_ARRP			0x20000000
-#define EMAC_RMR_ARP			0x10000000
-#define EMAC_RMR_AROP			0x08000000
-#define EMAC_RMR_ARPI			0x04000000
-#define EMAC_RMR_PPP			0x02000000
-#define EMAC_RMR_PME			0x01000000
-#define EMAC_RMR_PMME			0x00800000
-#define EMAC_RMR_IAE			0x00400000
-#define EMAC_RMR_MIAE			0x00200000
-#define EMAC_RMR_BAE			0x00100000
-#define EMAC_RMR_MAE			0x00080000
-
-/* Interrupt Status & enable Regs */
-#define EMAC_ISR_OVR			0x02000000
-#define EMAC_ISR_PP			0x01000000
-#define EMAC_ISR_BP			0x00800000
-#define EMAC_ISR_RP			0x00400000
-#define EMAC_ISR_SE			0x00200000
-#define EMAC_ISR_SYE			0x00100000
-#define EMAC_ISR_BFCS			0x00080000
-#define EMAC_ISR_PTLE			0x00040000
-#define EMAC_ISR_ORE			0x00020000
-#define EMAC_ISR_IRE			0x00010000
-#define EMAC_ISR_DBDM			0x00000200
-#define EMAC_ISR_DB0			0x00000100
-#define EMAC_ISR_SE0			0x00000080
-#define EMAC_ISR_TE0			0x00000040
-#define EMAC_ISR_DB1			0x00000020
-#define EMAC_ISR_SE1			0x00000010
-#define EMAC_ISR_TE1			0x00000008
-#define EMAC_ISR_MOS			0x00000002
-#define EMAC_ISR_MOF			0x00000001
-
-
-/* STA CONTROL REG */
-#define EMAC_STACR_OC			0x00008000
-#define EMAC_STACR_PHYE			0x00004000
-#define EMAC_STACR_WRITE		0x00002000
-#define EMAC_STACR_READ			0x00001000
-#define EMAC_STACR_CLK_83MHZ		0x00000800  /* 0's for 50Mhz */
-#define EMAC_STACR_CLK_66MHZ		0x00000400
-#define EMAC_STACR_CLK_100MHZ		0x00000C00
-
-/* Transmit Request Threshold Register */
-#define EMAC_TRTR_256			0x18000000   /* 0's for 64 Bytes */
-#define EMAC_TRTR_192			0x10000000
-#define EMAC_TRTR_128			0x01000000
-
-/* the follwing defines are for the MadMAL status and control registers. */
-/* For bits 0..5 look at the mal.h file                                  */
-#define EMAC_TX_CTRL_GFCS 	0x0200
-#define EMAC_TX_CTRL_GP		0x0100
-#define EMAC_TX_CTRL_ISA	0x0080
-#define EMAC_TX_CTRL_RSA	0x0040
-#define EMAC_TX_CTRL_IVT	0x0020
-#define EMAC_TX_CTRL_RVT	0x0010
-
-#define EMAC_TX_CTRL_DEFAULT (EMAC_TX_CTRL_GFCS |EMAC_TX_CTRL_GP)
-
-#define EMAC_TX_ST_BFCS		0x0200
-#define EMAC_TX_ST_BPP		0x0100
-#define EMAC_TX_ST_LCS		0x0080
-#define EMAC_TX_ST_ED		0x0040
-#define EMAC_TX_ST_EC		0x0020
-#define EMAC_TX_ST_LC		0x0010
-#define EMAC_TX_ST_MC		0x0008
-#define EMAC_TX_ST_SC		0x0004
-#define EMAC_TX_ST_UR		0x0002
-#define EMAC_TX_ST_SQE		0x0001
-
-#define EMAC_TX_ST_DEFAULT    0x03F3
-
-
-/* madmal receive status / Control bits */
-
-#define EMAC_RX_ST_OE		0x0200
-#define EMAC_RX_ST_PP		0x0100
-#define EMAC_RX_ST_BP		0x0080
-#define EMAC_RX_ST_RP		0x0040
-#define EMAC_RX_ST_SE		0x0020
-#define EMAC_RX_ST_AE		0x0010
-#define EMAC_RX_ST_BFCS		0x0008
-#define EMAC_RX_ST_PTL		0x0004
-#define EMAC_RX_ST_ORE		0x0002
-#define EMAC_RX_ST_IRE		0x0001
-/* all the errors we care about */
-#define EMAC_RX_ERRORS		0x03FF
-
-#define NUM_RX_BUFF PKTBUFSRX
-#define NUM_TX_BUFF 1
-
-#define MAX_ERR_LOG 10
-typedef struct emac_stats_st{	/* Statistic Block */
-	int data_len_err;
-	int rx_frames;
-	int rx;
-	int rx_prot_err;
-	int int_err;
-	int pkts_tx;
-	int pkts_rx;
-	int pkts_handled;
-	short tx_err_log[MAX_ERR_LOG];
-	short rx_err_log[MAX_ERR_LOG];
-} EMAC_STATS_ST, *EMAC_STATS_PST;
-
-/* Structure containing variables used by the shared code (440gx_enet.c) */
-typedef struct emac_440gx_hw_st {
-	uint32_t		hw_addr;		/* EMAC offset */
-	uint32_t		tah_addr;		/* TAH offset */
-	uint32_t		phy_id;
-	uint32_t		phy_addr;
-	uint32_t		original_fc;
-	uint32_t		txcw;
-	uint32_t		autoneg_failed;
-	uint32_t		emac_ier;
-	volatile mal_desc_t *tx;
-	volatile mal_desc_t *rx;
-	bd_t		*bis;	/* for eth_init upon mal error */
-	mal_desc_t		*alloc_tx_buf;
-	mal_desc_t		*alloc_rx_buf;
-	char		*txbuf_ptr;
-	uint16_t		devnum;
-	int			get_link_status;
-	int			tbi_compatibility_en;
-	int			tbi_compatibility_on;
-	int			fc_send_xon;
-	int			report_tx_early;
-	int			first_init;
-	int			tx_err_index;
-	int			rx_err_index;
-	int			rx_slot;			/* MAL Receive Slot */
-	int			rx_i_index;		/* Receive Interrupt Queue Index */
-	int			rx_u_index;		/* Receive User Queue Index */
-	int			tx_slot;			/* MAL Transmit Slot */
-	int			tx_i_index;		/* Transmit Interrupt Queue Index */
-	int			tx_u_index;		/* Transmit User Queue Index */
-	int			rx_ready[NUM_RX_BUFF];	/* Receive Ready Queue */
-	int			tx_run[NUM_TX_BUFF];	/* Transmit Running Queue */
-	int			is_receiving;	/* sync with eth interrupt */
-	int			print_speed;	/* print speed message upon start */
-	EMAC_STATS_ST	stats;
-} EMAC_405_HW_ST, *EMAC_405_HW_PST;
-
-/*-----------------------------------------------------------------------------+
-| Function prototypes for device table.
-+-----------------------------------------------------------------------------*/
-#endif /* _enetLib_h_ */
diff --git a/include/asm-ppc/u-boot.h b/include/asm-ppc/u-boot.h
index 161a29506b..4fcebe7a4f 100644
--- a/include/asm-ppc/u-boot.h
+++ b/include/asm-ppc/u-boot.h
@@ -109,14 +109,18 @@ typedef struct bd_info {
 #if defined(CONFIG_NX823)
 	unsigned char	bi_sernum[8];
 #endif
-#if defined(CONFIG_440EP) || defined(CONFIG_440GR)
-	int 		bi_phynum[2];           /* Determines phy mapping */
-	int 		bi_phymode[2];          /* Determines phy mode */
-#endif
+#if defined(CONFIG_4xx)
 #if defined(CONFIG_440GX)
 	int 		bi_phynum[4];           /* Determines phy mapping */
 	int 		bi_phymode[4];          /* Determines phy mode */
+#elif defined(CONFIG_405EP) || defined(CONFIG_440)
+	int 		bi_phynum[2];           /* Determines phy mapping */
+	int 		bi_phymode[2];          /* Determines phy mode */
+#else
+	int 		bi_phynum[1];           /* Determines phy mapping */
+	int 		bi_phymode[1];          /* Determines phy mode */
 #endif
+#endif /* defined(CONFIG_4xx) */
 } bd_t;
 
 #endif /* __ASSEMBLY__ */
diff --git a/include/configs/KAREF.h b/include/configs/KAREF.h
index 331131aba7..00a6e5d55d 100644
--- a/include/configs/KAREF.h
+++ b/include/configs/KAREF.h
@@ -166,6 +166,7 @@
 #define CONFIG_HAS_ETH1
 #define CONFIG_HAS_ETH2
 #define CONFIG_HAS_ETH3
+#define CONFIG_PHY_RESET      1              /* reset phy upon startup  */
 #define CONFIG_CIS8201_PHY    1		     /* RGMII mode for Cicada	*/
 #define CONFIG_CIS8201_SHORT_ETCH 1	     /* Use short etch mode	*/
 #define CONFIG_PHY_GIGE	      1		     /* GbE speed/duplex detect */
diff --git a/include/configs/METROBOX.h b/include/configs/METROBOX.h
index 2b4a33f4ca..cf6f00ef92 100644
--- a/include/configs/METROBOX.h
+++ b/include/configs/METROBOX.h
@@ -230,6 +230,7 @@
 #define CONFIG_HAS_ETH1
 #define CONFIG_HAS_ETH2
 #define CONFIG_HAS_ETH3
+#define CONFIG_PHY_RESET      1              /* reset phy upon startup  */
 #define CONFIG_CIS8201_PHY    1		     /* RGMII mode for Cicada	*/
 #define CONFIG_CIS8201_SHORT_ETCH 1	     /* Use short etch mode	*/
 #define CONFIG_PHY_GIGE	      1		     /* GbE speed/duplex detect */
diff --git a/include/configs/XPEDITE1K.h b/include/configs/XPEDITE1K.h
index 347bb50332..2e0b1a45f5 100644
--- a/include/configs/XPEDITE1K.h
+++ b/include/configs/XPEDITE1K.h
@@ -175,6 +175,7 @@ extern void out32(unsigned int, unsigned long);
 #define CONFIG_PHY3_ADDR	8	/* PHY address phy3 */
 #define CONFIG_NET_MULTI	1
 #define CONFIG_PHY_GIGE		1	/* Include GbE speed/duplex detection */
+#define CONFIG_PHY_RESET        1       /* reset phy upon startup         */
 #define CFG_RX_ETH_BUFFER   32	/* Number of ethernet rx buffers & descriptors */
 
 #define CONFIG_HAS_ETH1		1	/* add support for "eth1addr"	*/
diff --git a/include/configs/bamboo.h b/include/configs/bamboo.h
index 64ea6bef91..910de67efd 100644
--- a/include/configs/bamboo.h
+++ b/include/configs/bamboo.h
@@ -275,15 +275,13 @@
 
 #define CONFIG_MII		1	/* MII PHY management		*/
 #define CONFIG_PHY_ADDR		0	/* PHY address, See schematics	*/
+#define CONFIG_PHY1_ADDR        1
 
 #ifndef CONFIG_BAMBOO_NAND
 #define CONFIG_NET_MULTI        1       /* required for netconsole      */
-#define CONFIG_PHY1_ADDR        1
 #define CONFIG_HAS_ETH1		1	/* add support for "eth1addr"	*/
 #endif /* CONFIG_BAMBOO_NAND */
 
-#define CONFIG_NO_PHY_RESET     1       /* no PHY reset on bamboo!!!    */
-
 #define CFG_RX_ETH_BUFFER	32	/* Number of ethernet rx buffers & descriptors */
 
 /* Partitions */
diff --git a/include/configs/ocotea.h b/include/configs/ocotea.h
index 2b0f6874c3..05a575bf63 100644
--- a/include/configs/ocotea.h
+++ b/include/configs/ocotea.h
@@ -211,8 +211,14 @@
 #define CONFIG_PHY1_ADDR	2
 #define CONFIG_PHY2_ADDR	0x10
 #define CONFIG_PHY3_ADDR	0x18
+#define CONFIG_HAS_ETH0
+#define CONFIG_HAS_ETH1
+#define CONFIG_HAS_ETH2
+#define CONFIG_HAS_ETH3
 #define CONFIG_CIS8201_PHY	1	/* Enable 'special' RGMII mode for Cicada phy */
 #define CONFIG_PHY_GIGE		1	/* Include GbE speed/duplex detection */
+#define CONFIG_PHY_RESET        1       /* reset phy upon startup         */
+#define CONFIG_PHY_RESET_DELAY	1000
 
 #define CONFIG_COMMANDS	       (CONFIG_CMD_DFL	| \
 				CFG_CMD_ASKENV	| \
@@ -256,7 +262,7 @@
 #define CFG_LOAD_ADDR		0x100000	/* default load address */
 #define CFG_EXTBDINFO		1	/* To use extended board_into (bd_t) */
 
-#define CFG_HZ		100		/* decrementer freq: 1 ms ticks */
+#define CFG_HZ			1000	/* decrementer freq: 1 ms ticks */
 
 #define CONFIG_AUTO_COMPLETE	1       /* add autocompletion support   */
 #define CONFIG_LOOPW            1       /* enable loopw command         */
diff --git a/include/440gx_enet.h b/include/ppc4xx_enet.h
index 45c2f46e63..eacfb68016 100644
--- a/include/440gx_enet.h
+++ b/include/ppc4xx_enet.h
@@ -38,10 +38,9 @@
 |	       ported to handle 440GP and 440GX multiple EMACs
 +----------------------------------------------------------------------------*/
 
-#ifndef _emacgx_enet_h_
-#define _emacgx_enet_h_
+#ifndef _PPC4XX_ENET_H_
+#define _PPC4XX_ENET_H_
 
-#if defined(CONFIG_440)
 #include <net.h>
 #include "405_mal.h"
 
@@ -84,15 +83,15 @@ typedef struct emac_stats_st{	/* Statistic Block */
 	int rx;
 	int rx_prot_err;
 	int int_err;
-    int pkts_tx;
-    int pkts_rx;
-    int pkts_handled;
+	int pkts_tx;
+	int pkts_rx;
+	int pkts_handled;
 	short tx_err_log[MAX_ERR_LOG];
 	short rx_err_log[MAX_ERR_LOG];
 } EMAC_STATS_ST, *EMAC_STATS_PST;
 
-/* Structure containing variables used by the shared code (440gx_enet.c) */
-typedef struct emac_440gx_hw_st {
+/* Structure containing variables used by the shared code (4xx_enet.c) */
+typedef struct emac_4xx_hw_st {
     uint32_t		hw_addr;		/* EMAC offset */
     uint32_t		tah_addr;		/* TAH offset */
     uint32_t		phy_id;
@@ -127,15 +126,15 @@ typedef struct emac_440gx_hw_st {
     int			is_receiving;	/* sync with eth interrupt */
     int			print_speed;	/* print speed message upon start */
     EMAC_STATS_ST	stats;
-} EMAC_440GX_HW_ST, *EMAC_440GX_HW_PST;
+} EMAC_4XX_HW_ST, *EMAC_4XX_HW_PST;
 
 
 #if defined(CONFIG_440GX)
 #define EMAC_NUM_DEV	    4
-#elif defined(CONFIG_440) && !defined(CONFIG_440GX)
+#elif (defined(CONFIG_440) || defined(CONFIG_405EP)) && defined(CONFIG_NET_MULTI)
 #define EMAC_NUM_DEV	    2
 #else
-#warning Bad configuration
+#define EMAC_NUM_DEV	    1
 #endif
 
 
@@ -224,7 +223,6 @@ typedef struct emac_440gx_hw_st {
 #define TAH_SSR5		(TAH_BASE + 0x28)   /* Segment Size Reg 5 (R/W) */
 #define TAH_TSR			(TAH_BASE + 0x2C)   /* Transmit Status Register (RO) */
 
-
 /* TAH Revision */
 #define TAH_REV_RN_M		(0x000FFF00)	    /* Revision Number */
 #define TAH_REV_BN_M		(0x000000FF)	    /* Branch Revision Number */
@@ -276,11 +274,15 @@ typedef struct emac_440gx_hw_st {
 
 
 /* Ethernet MAC Regsiter Addresses */
+#if defined(CONFIG_440)
 #if defined(CONFIG_440EP) || defined(CONFIG_440GR)
 #define EMAC_BASE			    (CFG_PERIPHERAL_BASE + 0x0E00)
 #else
 #define EMAC_BASE			    (CFG_PERIPHERAL_BASE + 0x0800)
 #endif
+#else
+#define EMAC_BASE 			0xEF600800
+#endif
 
 #define EMAC_M0				    (EMAC_BASE)
 #define EMAC_M1				    (EMAC_BASE + 4)
@@ -471,5 +473,4 @@ typedef struct emac_440gx_hw_st {
 /* all the errors we care about */
 #define EMAC_RX_ERRORS		(0x03FF)
 
-#endif /* CONFIG_440 */
-#endif /* _enetLib_h_ */
+#endif /* _PPC4XX_ENET_H_ */
diff --git a/net/eth.c b/net/eth.c
index 61862aaba9..68dfcae7a7 100644
--- a/net/eth.c
+++ b/net/eth.c
@@ -47,7 +47,6 @@ extern int ns8382x_initialize(bd_t*);
 extern int pcnet_initialize(bd_t*);
 extern int plb2800_eth_initialize(bd_t*);
 extern int ppc_4xx_eth_initialize(bd_t *);
-extern int ppc_440x_eth_initialize(bd_t *);
 extern int rtl8139_initialize(bd_t*);
 extern int rtl8169_initialize(bd_t*);
 extern int scc_initialize(bd_t*);
@@ -126,13 +125,9 @@ int eth_initialize(bd_t *bis)
 #ifdef CONFIG_DB64460
 	mv6446x_eth_initialize(bis);
 #endif
-#if defined(CONFIG_405GP) || defined(CONFIG_405EP) || \
-  ( defined(CONFIG_440) && !defined(CONFIG_NET_MULTI) )
+#if defined(CONFIG_4xx) && !defined(CONFIG_IOP480)
 	ppc_4xx_eth_initialize(bis);
 #endif
-#if defined(CONFIG_440) && defined(CONFIG_NET_MULTI)
-	ppc_440x_eth_initialize(bis);
-#endif
 #ifdef CONFIG_INCA_IP_SWITCH
 	inca_switch_initialize(bis);
 #endif