u-boot.git/include/version.h, branch LABEL_2004_04_18_2135

Fix if / elif handling bug in HUSH shell

2004-04-12T14:31:43+00:00

Release version 1.1.0

2004-04-10T20:44:51+00:00

Add a common get_ram_size() function and modify the the

2004-01-06T22:38:14+00:00

board-specific files to invoke that common implementation.

* Patch by Bernhard Kuhn, 28 Oct 2003:

2003-11-07T13:42:26+00:00

  Add low boot support for MPC5200

* Fix problem with dual PCMCIA support (NSCU)

* Fix MPC5200 I2C initialization function

* Prepare for release

2003-10-29T23:18:55+00:00

* Fix problems in memory test on some boards (which was not
  non-destructive as intended)

* Patch by Gary Jennejohn, 28 Oct 2003:
  Change fs/fat/fat.c to put I/O buffers in BSS instead on the stack
  to prevent stack overflow on ARM systems

* Patch by Gary Jennejohn, 11 Sep 2003:

2003-09-11T19:48:06+00:00

  - allow for longer timeouts for USB mass storage devices

* Patch by Denis Peter, 11 Sep 2003:
  - fix USB data pointer assignment for bulk only transfer.
  - prevent to display erased directories in FAT filesystem.

* Change output format for NAND flash - make it look like for other
  memory, too

Patch by Yuli Barcohen, 7 Aug 2003:

2003-08-31T18:37:54+00:00

According to the MPC8260 User's Manual, PCI_MODE signal should be
reflected in SCCR register, and local bus pins configuration is taken
from HRCW and appears in SIUMCR. For some reason it does not work
this way, so the only possibility to detect if the board is
configured in PCI mode is to check the BCSR. This patch sets SCCR and
SIUMCR according to the BCSR.

* Fix ICU862 environment problem

2003-08-28T09:41:22+00:00

* Fix RAM size detection for RMU board

* Implement "reset" for MGT5100/MPC5200 systems

* Make Ethernet autonegotiation on INCA-IP work for all clock rates;

2003-08-17T18:55:18+00:00

  allow selection of clock frequency as "make" target

* Implement memory autosizing code for IceCube boards

* Configure network port on INCA-IP for autonegotiation

* Fix overflow problem in network timeout code

* Patch by Richard Woodruff, 8 Aug 2003:
  Allow crc32 to be used at address 0x000 (crc32_no_comp, too).

* Patch by Martin Krause, 17 Jul 2003:

2003-07-17T23:16:40+00:00

  add delay to get I2C working with "imm" command and s3c24x0_i2c.c

* Patch by Richard Woodruff, 17 July 03:
  - Fixed bug in OMAP1510 baud rate divisor settings.

* Patch by Nye Liu, 16 July 2003:
  MPC860FADS fixes:
  - add MPC86xADS support (uses MPC86xADS.h)
  - add 866P/T core support (also MPC859T/MPC859DSL/MPC852T)
    o PLPRCR changes
    o BRG changes (EXTAL/XTAL restricted to 10MHz)
    o don't trust gclk() software measurement by default, depend on
      CONFIG_8xx_GCLK_FREQ
  - add DRAM SIMM not installed detection
  - use more "correct" SDRAM initialization sequence
  - allow different SDRAM sizes (8xxADS has 8M)
  - default DER is 0
  - remove unused MAMR defines from FADS860T.h (all done in fads.c)
  - rename MAMR/MBMR defines to be more consistent. Should eventually
    be merged into MxMR to better reflect the PowerQUICC datasheet.

* Patch by Yuli Barcohen, 16 Jul 2003:
  support new Motorola PQ2FADS-ZU evaluation board which replaced
  MPC8260ADS and MPC8266ADS