To make sure that the mux can be configured a deblocking sequence
is done before the mux configuration. After the mux switch the new leaf
of, the i2c tree must be again deblocked.

Signed-off-by: Stefan Bigler <stefan.bigler@keymile.com>
Acked-by: Heiko Schocher <hs@denx.de>
cc: Wolfgang Denk <wd@denx.de>
cc: Detlev Zundel <dzu@denx.de>
cc: Prafulla Wadaskar <prafulla@marvell.com>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>

This patch adds a callpoint in i2c_init that allows board specific
i2c board initialization (typically for i2c bus reset) that is called
after i2c_init operations, allowing the i2c_board_late_init function
to use the pre-configured i2c bus speed and slave address.

and removed it from the .h file

Signed-off-by: Frans Meulenbroeks <fransmeulenbroeks@gmail.com>

* add's a warning to all files, which need update to new SoC access
 * convert common files in cpu/../at91 and a lot of drivers to use
   c stucture SoC access

Signed-off-by: Jens Scharsig <js_at_ng@scharsoft.de>

- CONFIG_SYS_MAX_I2C_BUS changed to 1
  We use only one I2C hardwarecontroller on this boards, so
  change the CONFIG_SYS_MAX_I2C_BUS to 1.
- common: dont print errormsg if second IVM Block lacks.
- 82xx, mgcoge: fix double mtdpart entry in environment
- 82xx, mgcoge: activate on second Flash the second bank.
- common: CONFIG_ENV_SIZE 0x4000 for all keymile boards
- common: Change malloc size to 1MByte for all Keymile boards
    We need a bigger malloc area for the environment support (128k)
    on some Keymile boards (kmeter1) and the upcoming UBI support.
    Change it to 1MB for all Keymile boards to be on the save side.
    Also define CONFIG_SYS_64BIT_VSPRINTF which is needed for
    UBI/UBIFS support.
- Add UBI support to all Keymile boards
- change manner of writing "/localbus/ranges" node
    instead of writting the complete "/localbus/ranges" node
    before booting Linux, only update the ranges entries
    which gets dynamical detected (size of flashes).
    This is needed, because keymile adds in the DTS
    "/localbus/ranges" node entries, which u-boot must
    not overwrite/delete.
- kmeter, mgcoge: define 2 seperate regions needed for the Intel P30 chips
    The Intel P30 chip has 2 non-identical chips on
    one die, so we need to define 2 seperate regions
    that are scanned by physmap_of independantly.
- kmeter1: Add MTD concat support to Keymile boards
- 82xx, mgcoge: add "unlock=yes" to default environment
- added CONFIG_MTD_DEVICE to get in sync with mainline code

Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>

Many boards/controllers/drivers don't support an I2C slave interface,
however CONFIG_SYS_I2C_SLAVE is used in common code so provide a
default

Signed-off-by: Peter Tyser <ptyser@xes-inc.com>

The Blackfin i2c driver has been rewritten thus the special ifdefs in the
common code are no longer needed.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>

All implementations of the functions i2c_reg_read() and
i2c_reg_write() are identical. We can save space and simplify the
code by converting these functions into inlines and putting them in
i2c.h.

Signed-off-by: Timur Tabi <timur@freescale.com>
Acked-By: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

With this Command it is possible to add new I2C Busses,
which are behind 1 .. n I2C Muxes. Details see README.

Signed-off-by: Heiko Schocher <hs@denx.de>