u-boot.git/include/configs/km, branch master

board/km: add support for seli8 design based on nxp ls102x

2021-04-15T08:52:17+00:00

The SELI8 design is a new tdm service unit card for Hitachi-Powergrids
XMC and FOX product lines.

It is based on NXP LS1021 SoC and it provides following interfaces:
 - IFC interface for NOR, NAND and external FPGA's
 - 1 x RGMII ETH for debug purposes
 - 2 x SGMII ETH for management communication via back-plane
 - 1 x uQE HDLC for management communication via back-plane
 - 1 x I2C for peripheral devices
 - 1 x SPI for peripheral devices
 - 1 x UART for debug logging

It is foreseen that the design will be later re-used for another XMC and
FOX service cards with similar SoC requirements.

Signed-off-by: Rainer Boschung 
Signed-off-by: Matteo Ghidoni 
Signed-off-by: Aleksandar Gerasimovski 
Reviewed-by: Priyanka Jain

board/km: move km i2c deblock declarations to a km/common.h

2021-02-08T08:31:18+00:00

Cleanup, move the declarations to keymile/common.h instead declaring them
per-board config.h

Signed-off-by: Aleksandar Gerasimovski 
Reviewed-by: Tom Rini 
Reviewed-by: Priyanka Jain

Merge tag 'v2021.01-rc5' into next

2021-01-05T21:20:26+00:00

Prepare v2021.01-rc5

Signed-off-by: Tom Rini

km/common: remove CONFIG_MTD_CONCAT

2020-12-02T21:21:58+00:00

This was used for a board which is not supproted anymore and can
therefore be dropped.

CC: Stefan Roese 
Signed-off-by: Holger Brunck 
Reviewed-by: Stefan Roese

remove obsolete option CONFIG_JFFS2_CMDLINE

2020-12-02T21:21:58+00:00

This option is obsolete since 2009 and can be removed globally.

CC: Stefan Roese 
Signed-off-by: Holger Brunck 
Reviewed-by: Stefan Roese

km/arm: coding style clean up

2020-12-01T19:12:28+00:00

Address most of the checkpatch issues we found in km_arm and common km
code.

CC: Stefan Roese 
CC: Valentin Longchamp 
Signed-off-by: Holger Brunck 
Reviewed-by: Stefan Roese

km: replace hardcoded address for imported environment

2020-11-19T14:45:49+00:00

Instead of using an hard coded address, make use of an
already defined address for importing the environment
for ramfs and nfs boot. This allows boards having different
mapping to use the same code.

CC: Heiko Schocher 
CC: Tom Rini 
Signed-off-by: Matteo Ghidoni 
Signed-off-by: Holger Brunck

km/common: change ubicopy variable

2020-10-22T15:26:08+00:00

Instead having a hard coded value for "cramfsaddr" after compile time,
we change it to take the variable "cramfsaddr" for the ubicopy variable.
This makes sure that ubicopy uses the right address, even when
the value for "cramfsaddr" has changed.

CC: Valentin Longchamp 
CC: Heiko Schocher 
CC: Tom Rini 
Signed-off-by: Holger Brunck 
Reviewed-by: Heiko Schocher

km: adapt defines and variables for new memory layout

2020-10-22T15:25:33+00:00

Due to increasing kernel image sizes we get problems when decompressing
the kernel image. To fix this we need to change the addresses where we
load and where we extract the kernel. Also we need to adapt the address
where to load the CRAMFS image and where to load the DTB file.
While at it also harmonize all boards for PPC and ARM to have the
same values. Also we add a new variable "env_version", so that the
userspace is able to detect if this is a u-boot binary with updated
values or not.

CC: Valentin Longchamp 
CC: Heiko Schocher 
CC: Tom Rini 
Signed-off-by: Holger Brunck 
Reviewed-by: Heiko Schocher 
[trini: Remove old values from kmp204x.h]
Signed-off-by: Tom Rini

mpc83xx, keymile boards: enable DM_ETH and add DTS

2020-09-17T04:09:54+00:00

enable DTS support for keymile mpc83xx based boards.

get rid of compile warning:
===================== WARNING ======================
This board does not use CONFIG_DM_ETH (Driver Model
for Ethernet drivers). Please update the board to use
CONFIG_DM_ETH before the v2020.07 release. Failure to
update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
====================================================

Therefore done:
- add DTS for all mpc83xx based boards from keymile
  mainly they are not mainlined to linux.
- add u-boot specific dtsi
- add stdout-path
- add missing ucc4 par_io definitions, which were
  in board code, but not in linux DTS
- remove not used ethernet nodes

Signed-off-by: Heiko Schocher 
Patch-cc: Mario Six 
Patch-cc: Qiang Zhao 

Series-to: u-boot

Series-version: 3

Series-changes: 3
- rebase patchset to current mainline commit
  c0192950df
- update defconfig files

Series-changes: 2
- add patch which fixes Codingstyle errors in drivers/qe
- add patch which converts the mpc83xx based boards from
  keymile to DM_ETH

Cover-letter:
powerpc, mpc83xx: add DM_ETH support

This patch series adds DM ethernet support for mpc83xx based
keymile boards.

Travis build:

END