u-boot.git/drivers/usb/host, branch v2011.06

ehci-pci: Fix PCI EHCI driver for 36-bit

2011-06-25T07:53:10+00:00

Convert the PCI base address into a virtual address.

Signed-off-by: Zhao Chenhui 
Signed-off-by: Li Yang

AT91: change includes from asm/arch/io.h to asm/io.h

2011-05-18T05:56:51+00:00

and remove the now unused asm/arch-at91/io.h

Signed-off-by: Reinhard Meyer

AT91: fix related at91 driver files

2011-05-18T05:56:51+00:00

Signed-off-by: Reinhard Meyer

IMX: MX31: Cleanup include files and drop nasty #ifdef in drivers

2011-04-27T17:38:05+00:00

As exception among the i.MX processors, the i.MX31 has headers
without general names (mx31-regs.h, mx31.h instead of imx-regs.h and
clock.h). This requires several nasty #ifdef in the drivers to
include the correct header. The patch cleans up the driver and
renames the header files as for the other i.MX processors.

Signed-off-by: Stefano Babic

Merge branch 'master' of git://git.denx.de/u-boot-mpc85xx

2011-04-05T10:24:20+00:00

Conflicts:
	drivers/usb/host/ehci-pci.c

Signed-off-by: Wolfgang Denk

echi: add ULI1575 PCI ID

2011-04-04T14:24:42+00:00

Add ULI1575 EHCI controller to the list of the supported devices.

Signed-off-by: Zhao Chenhui 
Acked-by: Remy Bohmer 
Signed-off-by: Kumar Gala

ehci-pci: Add PCI EHCI controller

2011-04-02T07:38:24+00:00

This patch adds support for the PI7C9X442SL PCIe EHCI host controller
from Pericom.

Tested at P4080DS eval board from Freescale.

Signed-off-by: Ralf Trübenbach 
Cc: Remy Bohmer

Fix EHCI usb submit timeout and unify with OHCI

2011-02-19T19:32:34+00:00

Changed both to use a common timeout for URB submission, since they were using
different values and EHCI's was too short.

Also fixed EHCI to actually check if urb submission succeeded, rather than
silently continuing into the weeds.

Change-Id: I7f71499ffaa05187d8e5618db2419e1606007b82

Signed-off-by: Simon Glass

usb: Remove usb_dev_init() from ehci-ppc4xx.c

2010-11-26T20:24:57+00:00

Calling usb_dev_init() from within the EHCI host driver is wrong.
The EHCI host driver should have no dependency/interconnection to the
USB device driver.

Signed-off-by: Stefan Roese 
Cc: Remy Bohmer

usb: Clear CMD_RUN while issuing CMD_RESET in ehci_reset()

2010-11-26T20:23:25+00:00

This patch fixes a problem noticed on lwmon5 (PPC440EPx) using the
common EHCI driver, when "usb reset" is issued multiple times.
Upon the 2nd (and further) "usb reset" command, the command fails
with the following messages:

=> usb reset
(Re)start USB...
USB:   Register 1111 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... 5 USB Device(s) found
       scanning bus for storage devices... 2 Storage Device(s) found
=> usb reset
(Re)start USB...
USB:   EHCI fail to reset
Error, couldn't init Lowlevel part

This patch fixes this problem. Now "usb reset" can be called multiple
times.

Signed-off-by: Stefan Roese 
Cc: Remy Bohmer