u-boot.git/drivers/net/phy, branch v2013.01

mv88e61xx: refactor PHY and SWITCH level-code

2013-01-08T22:42:10+00:00

Signed-off-by: Albert ARIBAUD

phy: Add support for Marvell 88E1118R

2012-12-15T18:28:22+00:00

Marvell 88E1118R has different uid then 88E1118.

Signed-off-by: Michal Simek 
CC: Andy Fleming 
CC: Zang Roy-R61911 
CC: Kumar Gala

drivers/net/: sparse fixes

2012-11-04T18:00:36+00:00

phy.c:46:5: warning: symbol 'genphy_config_advert' was not declared. Should it be static?
phy.c:121:5: warning: symbol 'genphy_setup_forced' was not declared. Should it be static?
phy.c:468:5: warning: symbol 'phy_probe' was not declared. Should it be static?
phy.c:491:19: warning: symbol 'get_phy_driver' was not declared. Should it be static?
phy.c:508:19: warning: symbol 'phy_device_create' was not declared. Should it be static?
phy.c:552:5: warning: symbol 'get_phy_id' was not declared. Should it be static?
phy.c:584:19: warning: symbol 'get_phy_device' was not declared. Should it be sta
vitesse.c:126:5: warning: symbol 'vsc8601_config' was not declared. Should it be static?
vsc7385.c:33:5: warning: symbol 'vsc7385_upload_firmware' was not declared. Should it be static?
tgec_phy.c:33:5: warning: symbol 'tgec_mdio_write' was not declared. Should it be static?
tgec_phy.c:75:5: warning: symbol 'tgec_mdio_read' was not declared. Should it be static?
tgec_phy.c:117:5: warning: symbol 'tgec_mdio_reset' was not declared. Should it be static?
eth.c:48:6: warning: symbol 'dtsec_configure_serdes' was not declared. Should it be static?
p4080.c:26:5: warning: symbol 'port_to_devdisr' was not declared. Should it be static?

Signed-off-by: Kim Phillips

net/: sparse fixes

2012-11-04T18:00:36+00:00

bootp.c:44:14: warning: symbol 'dhcp_state' was not declared. Should it be static?
bootp.c:45:15: warning: symbol 'dhcp_leasetime' was not declared. Should it be static?
bootp.c:46:10: warning: symbol 'NetDHCPServerIP' was not declared. Should it be static?
arp.c:30:17: warning: symbol 'NetArpWaitReplyIP' was not declared. Should it be static?
arp.c:37:16: warning: symbol 'NetArpTxPacket' was not declared. Should it be static?
arp.c:38:17: warning: symbol 'NetArpPacketBuf' was not declared. Should it be static?
atheros.c:33:19: warning: symbol 'AR8021_driver' was not declared. Should it be static?
net.c:183:7: warning: symbol 'PktBuf' was not declared. Should it be static?
net.c:159:21: warning: symbol 'net_state' was not declared. Should it be static?
ping.c:73:6: warning: symbol 'ping_start' was not declared. Should it be static?
ping.c:82:13: warning: symbol 'ping_receive' was not declared. Should it be static?
tftp.c:53:7: warning: symbol 'TftpRRQTimeoutMSecs' was not declared. Should it be static?
tftp.c:54:5: warning: symbol 'TftpRRQTimeoutCountMax' was not declared. Should it be static?
eth.c:125:19: warning: symbol 'eth_current' was not declared. Should it be static?

Note: in the ping.c fix, commit a36b12f95a29647a06b5459198684fc142482020
"net: Move PING out of net.c" mistakenly carried the ifdef CMD_PING
clause from when it was necessary to avoid warnings when it was embedded
in net.c.

Signed-off-by: Kim Phillips

net: Add Vitesse VSC8662 PHY support

2012-09-27T17:21:59+00:00

-VSC8662 is Dual Port 10/100/1000Base-T Phy,
 100Base-FX/1000/Base-X Gigabit Ethernt Transceiver Phy.

-Its register set and features are similar to
 other Vitesse Phys

Signed-off-by: Priyanka Jain 
Signed-off-by: York Sun

net/phy: support the mv88e6352 switch

2012-09-27T17:21:56+00:00

This patch add support for the configuration of an external switch from
the 88E6xxx series from Marvell trough an MDIO link using indirect
adressing. This can be used if we do not want to use an EEPROM for the
configuration.

This driver is not generic and was not tested on other switches than the
88e6352. This is proposed as a first implementation that is somewhat
limited but works and that can be used as a basis for further
developments for this switch family.

Signed-off-by: Valentin Longchamp 
cc: Holger Brunck 
cc: Prafulla Wadaskar 
cc: Joe Hershberger

net: phy: micrel: make ksz9021 phy accessible

2012-07-11T18:15:30+00:00

Micrel accidentally used the same part number
for the KS8721 and KSZ9021. So, both cannot be
in the same build of u-boot. Add a config option
to handle this.

Signed-off-by: Troy Kisky 
Acked-by: Vladimir Zapolskiy

phylib: phy_startup() should return an error code on failure

2012-07-11T18:15:30+00:00

phy_startup() calls the PHY driver's startup function, but it ignores the
return code from that function, and so it never returns any failures.

Signed-off-by: Timur Tabi

net: phy: make board_phy_config responsible for calling drv->config

2012-02-27T20:19:25+00:00

Boards may have things they want done before or after normal phy config.
Letting the boards call drv->config allows them more flexibilty.
Boards affected by this change are corenet_ds and mpc8544ds.

Signed-off-by: Troy Kisky 
Acked-by: Dirk Behme

net: phy: add support for Micrel's KSZ9021

2012-02-27T20:19:25+00:00

Add the gigabit phy KSZ9021.
Also, add function ksz9021_phy_extended_write
/_read for access to the phys extended registers.
The environment variable "disable_giga"
can be used to disable 1000baseTx.

Signed-off-by: Troy Kisky 
Acked-by: Dirk Behme