u-boot.git/drivers/net/phy, branch v2011.09-rc2

phylib: remove a couple of redundant code lines

2011-09-09T22:08:26+00:00

This change slightly improves readability of the phydev speed/duplex
assignment logic.

Signed-off-by: Vladimir Zapolskiy 
Acked-by: Detlev Zundel

phylib: reset mii bus only if reset handler is registered

2011-09-09T22:07:55+00:00

This change allows to cope with a mii bus device registered using
miiphy_register(), which doesn't assign a default reset handler.

Signed-off-by: Vladimir Zapolskiy 
Acked-by: Detlev Zundel

phy.c: make less verbose - turn printf() into debug()

2011-08-31T20:35:27+00:00

The PHY driver was too verbose and corrupted the boot message display
like this:

	...
	Net:   TSEC0 connected to Marvell 88E1111S
	TSEC1 connected to Marvell 88E1111S
	TSEC0, TSEC1
	...

Turn printf() into debug() so we het the expected output again:

	...
	Net:   TSEC0, TSEC1
	...

Signed-off-by: Wolfgang Denk 
Cc: Kumar Gala

phylib: Detect link on 10G devices correctly

2011-07-27T21:21:25+00:00

gen10g_startup() had 2 bugs:

1) It had a boolean logic error in checking the MMD mask, and
always checked all of them.

2) It checked devices which don't actually report link state, which
meant that it would never believe the link was fully up.

Fix the boolean logic, and then mask the MMD mask so only link-reporting
devices are checked.

Signed-off-by: Andy Fleming 
Reported-by: Ed Swarthout

Minor coding style cleanup.

2011-05-19T20:22:44+00:00

Signed-off-by: Wolfgang Denk

phylib: Add a bunch of PHY drivers from tsec

2011-04-20T20:09:34+00:00

The tsec driver had a bunch of PHY drivers already written. This
converts them all into PHY Lib drivers, and serves as the first
set of PHY drivers for PHY Lib.

While doing that, cleaned up a number of magic numbers (though
not all of them, as PHY vendors like to keep their numbers as
magical as possible).  Also, noticed that almost all of the
vitesse/cicada PHYs had the same config/parse/startup functions,
so those have been collapsed into one.

Signed-off-by: Andy Fleming 
Signed-off-by: Kumar Gala 
Acked-by: Detlev Zundel

Create PHY Lib for U-Boot

2011-04-20T20:09:19+00:00

Extends the mii_dev structure to participate in a full-blown MDIO and
PHY driver scheme.  The mii_dev structure and miiphy calls are modified
in such a way to allow the original mii command and miiphy
infrastructure to work as before, but also to support a new set of APIs
which allow (among other things) sharing of PHY driver code and 10G support

The mii command will continue to support normal PHY management functions
(Clause 22 of 802.3), but will not be changed to support 10G
(Clause 45).

The basic design is similar to PHY Lib from Linux, but simplified for
U-Boot's network and driver infrastructure.

We now have MDIO drivers and PHY drivers

An MDIO driver provides:
read
write
reset

A PHY driver provides:
(optionally): probe
config - initial setup, starting of auto-negotiation
startup - waiting for AN, and reading link state
shutdown - any cleanup needed

The ethernet drivers interact with the PHY Lib using these functions:
phy_connect()
phy_config()
phy_startup()
phy_shutdown()

Each PHY driver can be configured separately, or all at once using
config_phylib_all_drivers.h (added in the patch which adds the drivers)

We also provide generic drivers for Clause 22 (10/100/1000), and
Clause 45 (10G) PHYs.

We also implement phy_reset(), and call it in phy_connect(). Because
phy_reset() is essentially the same as miiphy_reset, but:
a) must support 10G PHYs, and
b) should use the phylib primitives,

we implement miiphy_reset, using phy_reset(), but only when
CONFIG_PHYLIB is set. Otherwise, we just use the old version. In this
way, we save on compile size, even if we don't manage to save code size.

Pulled ethtool.h and mdio.h from:
git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6
782d640afd15af7a1faf01cfe566ca4ac511319d
With many, many deletions so as to enable compilation under u-boot

Signed-off-by: Andy Fleming 
Signed-off-by: Kumar Gala 
Acked-by: Detlev Zundel

miiphy: convert to linux/mii.h

2011-01-09T17:06:50+00:00

The include/miiphy.h header duplicates a lot of things from linux/mii.h.
So punt all the things that overlap to keep the API simple and to make
merging between U-Boot and Linux simpler.

Signed-off-by: Mike Frysinger

Switch from archive libraries to partial linking

2010-11-17T20:02:18+00:00

Before this commit, weak symbols were not overridden by non-weak symbols
found in archive libraries when linking with recent versions of
binutils.  As stated in the System V ABI, "the link editor does not
extract archive members to resolve undefined weak symbols".

This commit changes all Makefiles to use partial linking (ld -r) instead
of creating library archives, which forces all symbols to participate in
linking, allowing non-weak symbols to override weak symbols as intended.
This approach is also used by Linux, from which the gmake function
cmd_link_o_target (defined in config.mk and used in all Makefiles) is
inspired.

The name of each former library archive is preserved except for
extensions which change from ".a" to ".o".  This commit updates
references accordingly where needed, in particular in some linker
scripts.

This commit reveals board configurations that exclude some features but
include source files that depend these disabled features in the build,
resulting in undefined symbols.  Known such cases include:
- disabling CMD_NET but not CMD_NFS;
- enabling CONFIG_OF_LIBFDT but not CONFIG_QE.

Signed-off-by: Sebastien Carlier

Replace CONFIG_RELOC_FIXUP_WORKS by CONFIG_NEEDS_MANUAL_RELOC

2010-10-29T19:32:07+00:00

By now, the majority of architectures have working relocation
support, so the few remaining architectures have become exceptions.
To make this more obvious, we make working relocation now the default
case, and flag the remaining cases with CONFIG_NEEDS_MANUAL_RELOC.

Signed-off-by: Wolfgang Denk 
Tested-by: Heiko Schocher 
Tested-by: Reinhard Meyer