u-boot.git/drivers/net/phy/Kconfig, branch master

net: phy: xilinx: Drop #ifdef CONFIG_DM_ETH around phy_connect_gmii2rgmii()

2021-04-15T08:52:17+00:00

At present phy_connect_gmii2rgmii() is implemented using a DM API
dev_of_offset() hence it cannot support a non-DM configuration.
Remove the non-DM version prototype of phy_connect_gmii2rgmii()
and make the driver depend on CONFIG_DM_ETH.

Signed-off-by: Bin Meng 
Acked-by: Michal Simek 
Reviewed-by: Ramon Fried 
Reviewed-by: Vladimir Oltean 
Reviewed-by: Priyanka Jain

net: phy: ca_phy: Add driver for CAxxxx SoCs

2021-01-27T15:47:47+00:00

Add phy driver support for MACs embedded inside Cortina Access SoCs

Signed-off-by: Abbie Chang 
Signed-off-by: Alex Nemirovsky 

CC: Joe Hershberger 
CC: Tom Rini 
CC: Aaron Tseng 

Moved out PHY specific code out of Cortina NI Ethernet driver
and into a Cortina Access PHY interface driver

drivers/net/phy: Add CORTINA_NO_FW_UPLOAD to Kconfig

2020-12-10T08:26:39+00:00

Move CORTINA_NO_FW_UPLOAD to Kconfig file so that it can
be controlled via defconfig files.

Signed-off-by: Meenakshi Aggarwal 
Reviewed-by: Priyanka Jain

net: phy: realtek: Introduce PHY_RTL8201F_S700_RMII_TIMINGS to adjust rx/tx timings

2020-07-07T20:09:22+00:00

RTL8201F PHY module found on Actions Semi Cubieboard7 seems to have
specific Rx/Tx interface timings requirement for proper PHY operations.
These timing values are not documented anywhere and picked from vendor
code.

This commits lets proper packets to be transmitted over the network.

Signed-off-by: Amit Singh Tomar

net: phy: Add DP8382x phy registration to TI PHY init

2020-06-12T17:17:23+00:00

Add the DP8382X generic PHY registration to the TI PHY init file.

Acked-by: Michal Simek 
Signed-off-by: Dan Murphy

net: phy: Add support for TI PHY init

2020-06-12T17:17:23+00:00

ti_phy_init function was allocated to the DP83867 PHY.  This function
name is to generic for a specific PHY.  The function can be moved to a
TI specific file that can register all TI PHYs that are defined in the
defconfig.  The ti_phy_init file will contain all TI PHYs initialization
so that only phy_ti_init can be called from the framework.

In addition to the above the config flag for the DP83867 needs to be changed
in the Kconfig and dependent defconfig files. The config flag that was
used for the DP83867 was also generic in nature so a more specific
config flag for the DP83867 was created.

Acked-by: Michal Simek 
Signed-off-by: Dan Murphy

phy: Add support for the NC-SI protocol

2020-03-09T23:11:23+00:00

This introduces support for the NC-SI protocol, modelled as a phy driver
for other ethernet drivers to consume.

NC-SI (Network Controller Sideband Interface) is a protocol to manage a
sideband connection to a proper network interface, for example a BMC
(Baseboard Management Controller) sharing the NIC of the host system.
Probing and configuration occurs by communicating with the "remote" NIC
via NC-SI control frames (Ethernet header 0x88f8).

This implementation is roughly based on the upstream Linux
implementation[0], with a reduced feature set and an emphasis on getting
a link up as fast as possible rather than probing the full possible
topology of the bus.
The current phy model relies on the network being "up", sending NC-SI
command frames via net_send_packet() and receiving them from the
net_loop() loop (added in a following patch).

The ncsi-pkt.h header[1] is copied from the Linux kernel for consistent
field definitions.

[0]: https://github.com/torvalds/linux/tree/master/net/ncsi
[1]: https://github.com/torvalds/linux/blob/master/net/ncsi/ncsi-pkt.h

Signed-off-by: Samuel Mendoza-Jonas 
Reviewed-by: Joel Stanley 
Acked-by: Joe Hershberger

net: phy: fix switch vendor name

2019-12-09T15:47:42+00:00

Fix vendor name in MV88E61xx option description.

Signed-off-by: Anatolij Gustschin 
Reviewed-by: Chris Packham 
Tested-by: Chris Packham 
Acked-by: Joe Hershberger

Convert CONFIG_SYS_CORTINA_FW_IN_MMC et al to Kconfig

2019-12-03T13:43:24+00:00

This converts the following to Kconfig:
   CONFIG_SYS_CORTINA_FW_IN_MMC
   CONFIG_SYS_CORTINA_FW_IN_NAND
   CONFIG_SYS_CORTINA_FW_IN_NOR
   CONFIG_SYS_CORTINA_FW_IN_REMOTE
   CONFIG_SYS_CORTINA_FW_IN_SPIFLASH

Signed-off-by: Tom Rini

net: phy: Add gmiitorgmii converter support

2019-10-08T07:41:27+00:00

This patch adds support for gmiitorgmii converter.
This converter sits between the MAC and the external phy
MAC <==> GMII2RGMII <==> RGMII_PHY.
The ethernet driver probes this bridge and this bridge driver
probes real phy driver and invokes the real phy functionalities
as requested. This bridge just needs to be configured based on
real phy negotiated speed and duplex.

Signed-off-by: Siva Durga Prasad Paladugu 
Signed-off-by: Michal Simek