Add mmc-pwrseq file to provide a generic interface.

Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>

There are other (non-SDHCI) controllers which supports ADMA2 descriptor
tables, namely the Freescale eSDHC. Instead of copying the code, move it
into an own module.

Signed-off-by: Michael Walle <michael@walle.cc>

Adds support for MMC controllers found on OcteonTX or
OcteonTX2 SoC platforms.

Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Suneel Garapati <sgarapati@marvell.com>
Cc: Peng Fan <peng.fan@nxp.com>

Changes in relation to FriendlyARM's U-Boot nanopi2-v2016.01:
- driver changed to DM.
- pinctrl-driver/dt is used now instead of configuring the mmc I/O-pins
  in the mmc-driver.
- nexell_dwmmc_ofdata_to_platdata() reworked, i.e. valid default values
  are used now (where possible) and the appropriate if-blocks have
  been removed.
- new dt-property "mmcboost" is used now instead of "CONFIG_BOOST_MMC"
  which was not defined anywhere.

Signed-off-by: Stefan Bosch <stefan_b@posteo.net>

RPMB support is used by the 'mmc rpmb' command and by the OP-TEE support.
We do not need it in SPL.

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

Initial DesignWare based DM support for Cortina Access CAxxxx SoCs.

Signed-off-by: Arthur Li <arthur.li@cortina-access.com>
Signed-off-by: Alex Nemirovsky <alex.nemirovsky@cortina-access.com>

Add SDHCI driver for iProc family of Broadcom devices.

Signed-off-by: Corneliu Doban <corneliu.doban@broadcom.com>
Signed-off-by: Pramod Kumar <pramod.kumar@broadcom.com>
Signed-off-by: Pavithra Ravi <pavithra.ravi@broadcom.com>
Signed-off-by: Bharat Kumar Reddy Gooty <bharat.gooty@broadcom.com>
Signed-off-by: Vladimir Olovyannikov <vladimir.olovyannikov@broadcom.com>
Signed-off-by: Arun Parameswaran <arun.parameswaran@broadcom.com>

Add support for the Aspeed SD host controller engine.

Signed-off-by: Eddie James <eajames@linux.ibm.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>

Sync the sdhci0 node from kernel. This changes the compatible that is
required to be there in the driver. Change the same for the SD card node
which is not yet supported in kernel. This also syncs the main_pmx0 node
as a side effect.

Also change the name of the driver to match the compatible in kernel.

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

The fsl_esdhc driver was for Freescale eSDHC on MPC83XX/MPC85XX
initially. The later QoriQ series PowerPC processors (which were
evolutions of MPC83XX/MPC85XX), QorIQ series ARM processors, and
i.MX series processors were using this driver for their eSDHCs too.

For the two series processors, the eSDHCs are becoming more and
more different. We should have split it into two drivers, like them
(sdhci-of-esdhc.c/sdhci-esdhc-imx.c) in linux kernel.

This patch is just to create a fsl_esdhc_imx driver which is a copy
of fsl_esdhc driver for i.MX processors. We will convert i.MX processors
to use fsl_esdhc_imx, and clean up the two drivers separately in the
future patches.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Tested-by: Steffen Dirkwinkel <s.dirkwinkel@beckhoff.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Martyn Welch <martyn.welch@collabora.com>