u-boot.git/drivers/misc, branch v2011.09-rc2

Convert ISO-8859 files to UTF-8

2011-08-04T21:34:02+00:00

There was a mix of UTF-8 and ISO-8859 files in the U-Boot source
tree, which could cause issues with the patchwork review system.
This commit converts all ISO-8859 files to UTF-8.

Signed-off-by: Albert ARIBAUD

Minor coding style cleanup.

2011-05-19T20:22:44+00:00

Signed-off-by: Wolfgang Denk

powerpc/8xxx: Fix LAW init to respect pre-initialized entries

2011-04-04T14:24:41+00:00

If some pre-boot or earlier stage bootloader (NAND SPL) has setup LAW
entries consider them good and mark them used.

In the NAND SPL case we skip re-initializing based on the law_table
since the SPL phase already did that.

Signed-off-by: Kumar Gala

fsl_law: Fix LAW printing function

2011-02-23T05:25:19+00:00

We had an extra '0x' in the output of the LAWAR header that would cause
output like:

LAWBAR11: 0x00000000 LAWAR0x11: 0x80f0001d

intead of:

LAWBAR11: 0x00000000 LAWAR11: 0x80f0001d

Signed-off-by: Kumar Gala

Add basic support for Freescale's mc9sdz60

2011-02-01T23:54:43+00:00

The patch adds helper funtions for basic access to the registers
of the MC9sdz60 chip (multifunctional device with RTC and CAN) via
I2C interface.

Signed-off-by: Stefano Babic

fsl_pmic: add I2C interface support

2011-02-01T23:54:42+00:00

This patch add I2C interface for fsl_pmic driver support

Signed-off-by: Jason Liu

powerpc/8xxx: Introduce 85xx, 86xx, QorIQ config headers

2011-01-20T04:58:23+00:00

Add new headers that capture common defines for a given SoC/processor
rather than duplicating that information in board config.h and random
other places.

Eventually this should be handled by Kconfig & defconfigs

Signed-off-by: Kumar Gala 
Acked-by: Wolfgang Denk

powerpc/p2040: Add various p2040 specific information

2011-01-20T04:58:23+00:00

Add P2040 SoC specific information:
* SERDES Table
* Added p2040 to cpu_type_list and SVR list
* Added number of LAWs for p2040
* Set CONFIG_MAX_CPUS to 4 for p2040

Signed-off-by: Kumar Gala

powerpc/85xx: Add Support for Freescale P1014 Processor

2011-01-20T04:58:23+00:00

The P1014 is similar to the P1010 processor with the following differences:

- 16bit DDR with ECC. (P1010 has 32bit DDR w/o ECC)
- no eCAN interface. (P1010 has 2 eCAN interfaces)
- Two SGMII interface (P1010 has 3 SGMII)
- No secure boot

Signed-off-by: Poonam Aggrwal 
Signed-off-by: Kumar Gala

powerpc/85xx: Add Support for Freescale P1010 Processor

2011-01-20T04:58:23+00:00

Key Features include of the P1010:
* e500v2 core frequency operation of 500 to 800 MHz
* Power consumption less than 5.0 W at 800 MHz core speed
* Dual SATA 3 Gbps controllers with integrated PHY
* Dual PCI Express controllers
* Three 10/100/1000 Mbps enhanced triple-speed Ethernet controllers (eTSECs)
	* TCP/IP acceleration and classification capabilities
	* IEEE 1588 support
	* Lossless flow control
	* RGMII, SGMII
* DDR3 with support for a 32-bit data interface (40 bits including ECC),
  up to 800 MHz data rate 32/16-bit DDR3 memory controller
* Dedicated security engine featuring trusted boot
* TDM interface
* Dual controller area networks (FlexCAN) controller
* SD/MMC card controller supporting booting from Flash cards
* USB 2.0 host and device controller with an on-chip, high-speed PHY
* Integrated Flash controller (IFC)
* Power Management Controller (PMC)
* Four-channel, general-purpose DMA controller
* I2C controller
* Serial peripheral interface (SPI) controller with master and slave support
* System timers including a periodic interrupt timer, real-time clock,
  software watchdog timer, and four general-purpose timers
* Dual DUARTs

Signed-off-by: Poonam Aggrwal 
Signed-off-by: Dipen Dudhat 
Signed-off-by: Kumar Gala