u-boot.git/doc/README.uniphier, branch master

ARM: uniphier: enable distro boot

2018-07-24T23:47:53+00:00

Switch to the distro boot for UniPhier platform.

 - Remove the environment vairalbes used to load images from raw
   block devices.

 - Keep the command to download images via tftp.  This will be
   useful to boot the kernel when no valid kernel image is ready
   yet in the file system.

 - Use root.cpio.gz instead of root.cpio.uboot because we always know
   the file size of the init ramdisk; it is loaded via either a file
   system or network.

 - Rename fit_addr_r to kernel_addr_r, which the distro command
   checks to get the load address of FIT image.

Signed-off-by: Masahiro Yamada

doc: fix incorrect usage of DT node unit address

2018-01-16T01:29:21+00:00

The DT spec demands a unit-address in a node name to match the "reg"
property in that node. Newer dtc versions will throw warnings if this is
not the case.
Fix all occurences in various documentation files where this was not
observed, to not give bad examples to the reader.

Signed-off-by: Andre Przywara

doc: uniphier: add simple guide to Verified Boot

2017-10-22T16:09:22+00:00

Add a simple documentation about how to use the Verified Boot on
UniPhier boards.

Signed-off-by: Masahiro Yamada

ARM: uniphier: merge two defconfig files into uniphier_v7_defconfig

2017-09-18T11:26:06+00:00

The main difference between Pro4 and PXs2/LD6b is the Denali NAND
IP version.  This is now distinguished by DT.  Merge the two defconfig
files into uniphier_v7_defconfig.

Update the README.uniphier too.

Signed-off-by: Masahiro Yamada

ARM: uniphier: remove sLD3 SoC support

2017-08-20T14:05:39+00:00

This SoC is too old.  It is difficult to maintain any longer.

Signed-off-by: Masahiro Yamada

doc: uniphier: rework README.uniphier

2017-07-26T13:27:15+00:00

Rework the readme to reflect the latest boot mechanism on ARMv8 SoCs.

Signed-off-by: Masahiro Yamada

ARM: uniphier: remove SPL support for ARMv8 SoCs

2017-07-26T13:27:15+00:00

It has been a while since ARM Trusted Firmware supported UniPhier SoC
family.  U-Boot SPL was intended as a temporary loader that runs in
secure world.  It is a maintenance headache to support two different
boot mechanisms.  Secure firmware is realm of ARM Trusted Firmware
and now U-Boot only serves as a non-secure boot loader for UniPhier
ARMv8 SoCs.

Signed-off-by: Masahiro Yamada

ARM: uniphier: update README.uniphier for latest build instruction

2017-02-22T23:37:56+00:00

Since commit c0efc3140e75 ("ARM: uniphier: change CONFIG_SPL_PAD_TO
to 128KB"), the u-boot.bin should be burned at the offset 0x20000.
I missed to update README.uniphier in that commit.  Now updating.

Signed-off-by: Masahiro Yamada

ARM: uniphier: add PXs3 SoC support

2017-01-22T07:49:34+00:00

Initial support for PXs3 SoC.

Signed-off-by: Masahiro Yamada

ARM: uniphier: update doc/README.uniphier

2016-10-18T05:30:05+00:00

 - Rephrase the toolchains section.  Leave only Linaro toolchains
   since it is the most tested these days.

 - Add build instruction for ARMv8 SoC boards

 - Add information about "ddrmphy" command

Signed-off-by: Masahiro Yamada