If the param pass to get_dev is not the one defined in the block_drvr,
it could make uboot becomes unstable, for it would continue run after
search complete the block_drvr table.

Signed-off-by: Lei Wen <leiwen@marvell.com>

By now, the majority of architectures have working relocation
support, so the few remaining architectures have become exceptions.
To make this more obvious, we make working relocation now the default
case, and flag the remaining cases with CONFIG_NEEDS_MANUAL_RELOC.

Signed-off-by: Wolfgang Denk <wd@denx.de>
Tested-by: Heiko Schocher <hs@denx.de>
Tested-by: Reinhard Meyer <u-boot@emk-elektronik.de>

Portions of this work were supported by funding from
the CE Linux Forum.

Signed-off-by: Heiko Schocher <hs@denx.de>

Signed-off-by: Lei Wen <leiwen@marvell.com>

Before:
    Marvell>> usb storage
      Device 0: Vendor: StoreJet Rev:  Prod:  Transcend
                Type: Hard Disk
                Capacity: 28759.9 MB = 28.0 GB (488397168 x 512)
After:
    Marvell>> usb storage
      Device 0: Vendor: StoreJet Rev:  Prod:  Transcend
                Type: Hard Disk
                Capacity: 238475.1 MB = 232.8 GB (488397168 x 512)

Signed-off-by: Sergei Trofimovich <slyfox@gentoo.org>

There is more and more usage of printing 64bit values,
so enable this feature generally, and delete the
CONFIG_SYS_64BIT_VSPRINTF and CONFIG_SYS_64BIT_STRTOUL
defines.

Signed-off-by: Heiko Schocher <hs@denx.de>

Add #ifdefs where necessary to not perform relocation fixups.  This
allows boards/architectures which support relocation to trim a decent
chunk of code.

Note that this patch doesn't add #ifdefs to architecture-specific code
which does not support relocation.

Signed-off-by: Peter Tyser <ptyser@xes-inc.com>

Commit 574b319512 introduced a subtle bug by mixing a list of tests
for "dev_desc->type" and "dev_desc->if_type" into one switch(), which
then mostly did not work because "dev_desc->type" cannot take any
"IF_*" type values. A later fix in commit 8ec6e332ea changed the
switch() into testing "dev_desc->if_type", but at this point the
initial test for unknown device types was completely lost, which
resulted in output like that for IDE ports without device attached:

  Device 1: Model:  Firm:  Ser#:
            Type: # 1F #
            Capacity: not available

This patch re-introduces the missing test for unknown device types.

Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
Tested-by: Stefan Roese <sr@denx.de>

Mflash is fusion memory device mainly targeted consumer eletronic and
mobile phone.
Internally, it have nand flash and other hardware logics and supports
some different operation (ATA, IO, XIP) modes.

IO mode is custom mode for the host that doesn't have IDE interface.
(Many mobile targeted SoC doesn't have IDE bus)

This driver support mflash IO mode.

Followings are brief descriptions about IO mode.

1. IO mode based on ATA protocol and uses some custom command. (read
   confirm, write confirm)
2. IO mode uses SRAM bus interface.

Signed-off-by: unsik Kim <donari75@gmail.com>

This brings in support for the %p modifier which allows us to easily print
out things like ip addresses, mac addresses, and pointers.

It also converts the rarely used 'q' length modifier to the common 'L'
modifier when dealing with quad types.

While this new code is a bit larger (~1k .text), most of it should be made
up by converting the existing ip/mac address code to use format modifiers.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>