Signed-off-by: Peter Tyser <ptyser@xes-inc.com>

According to the PPC reference implementation the udelay() function is
responsible for resetting the watchdog timer as frequently as needed.
Most other architectures do not meet that requirement, so long-running
operations might result in a watchdog reset.

This patch adds a generic udelay() function which takes care of
resetting the watchdog before calling an architecture-specific
__udelay().

Signed-off-by: Ingo van Lil <inguin@gmx.de>

-fno-strict-aliasing is hidding warnings.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

For some time there have been repeated reports about build problems
with some ARM (cross) tool chains.  Especially issues about
(in)compatibility with the tool chain provided runtime support
library libgcc.a caused to add and support a private implementation
of such runtime support code in U-Boot.  A closer look at the code
indicated that some of these issues are actually home-made.  This
patch attempts to clean up some of the most obvious problems and make
building of U-Boot with different tool chains easier:

- Even though all ARM systems basicy used the same compiler options
  to select a specific ABI from the tool chain, the code for this was
  distributed over all cpu/*/config.mk files.  We move this one level
  up into lib_arm/config.mk instead.

- So far, we only checked if "-mapcs-32" was supported by the tool
  chain; if yes, this was used, if not, "-mabi=apcs-gnu" was
  selected, no matter if the tool chain actually understood this
  option.  There was no support for EABI conformant tool chains.
  This patch implements the following logic:

  1) If the tool chain supports
	"-mabi=aapcs-linux -mno-thumb-interwork"
     we use these options (EABI conformant tool chain).
  2) Otherwise, we check first if
	"-mapcs-32"
     is supported, and then check for
	"-mabi=apcs-gnu"
     If one test succeeds, we use the first found option.
  3) In case 2), we also test if "-mno-thumb-interwork", and use
     this if the test succeeds. [For "-mabi=aapcs-linux" we set
     "-mno-thumb-interwork" mandatorily.]

  This way we use a similar logic for the compile options as the
  Linux kernel does.

- Some EABI conformant tool chains cause external references to
  utility functions like raise(); such functions are provided in the
  new file lib_arm/eabi_compat.c

  Note that lib_arm/config.mk gets parsed several times, so we must
  make sure to add eabi_compat.o only once to the linker list.

Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Dirk Behme <dirk.behme@googlemail.com>
Cc: Magnus Lilja <lilja.magnus@gmail.com>
Cc: Tom Rix <Tom.Rix@windriver.com>
Cc: Prafulla Wadaskar <prafulla@marvell.com>
Acked-by: Sergey Kubushyn <ksi@koi8.net>
Tested-by: Magnus Lilja <lilja.magnus@gmail.com>
Tested-by: Andrzej Wolski <awolski@poczta.fm>
Tested-by: Gaye Abdoulaye Walsimou <walsimou@walsimou.com>
Tested-by: Tom Rix <Tom.Rix@windriver.com>
Tested-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

Signed-off-by: Magnus Lilja <lilja.magnus@gmail.com>

This patch adds the NAND SPL framework needed to boot i.MX31 boards
from NAND.

It has been tested on a i.MX31 PDK board with large page NAND. Small
page NANDs should work as well, but this has not been tested.

Note: The i.MX31 NFC uses a non-standard layout for large page NANDs,
whether this is compatible with a particular setup depends on how
the NAND device is programmed by the flash programmer (e.g. JTAG
debugger).

The patch is based on the work by Maxim Artamonov.

Signed-off-by: Maxim Artamonov <scn1874@yandex.ru>
Signed-off-by: Magnus Lilja <lilja.magnus@gmail.com>

Currently CONFIG_ONENAND_IPL is used in a number of #ifdef's
in start.S. In preparation for adding support for NAND SPL
the macro CONFIG_PRELOADER is introducted and replaces the
CONFIG_ONENAND_IPL in start.S.

Signed-off-by: Magnus Lilja <lilja.magnus@gmail.com>

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

move s3c44b0 to arch_cpu_init and as noone use cpu_init remove it

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

all arm init the IRQ stack the same way
so unify it in lib_arm/interrupts.c and then call arch specific interrupt init

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>