u-boot.git/configs/zipitz2_defconfig, branch master

arm: Remove zipitz2 board

2019-06-13T07:20:55+00:00

Per discussion on the list, drop this board again.

Cc: Vasily Khoruzhick 
Signed-off-by: Tom Rini 
Acked-by: Vasily Khoruzhick 
Reviewed-by: Jagan Teki

Convert CONFIG_FLASH_CFI_DRIVER et al to Kconfig

2018-10-19T23:19:50+00:00

This converts the following to Kconfig:
   CONFIG_FLASH_CFI_DRIVER
   CONFIG_SYS_FLASH_USE_BUFFER_WRITE
   CONFIG_FLASH_CFI_MTD
   CONFIG_SYS_FLASH_PROTECTION
   CONFIG_SYS_FLASH_CFI

Signed-off-by: Adam Ford 
[trini: Re-migrate]
Signed-off-by: Tom Rini

configs: Migrate CONFIG_NR_DRAM_BANKS

2018-08-16T20:45:02+00:00

We have the following cases:
- CONFIG_NR_DRAM_BANKS was defined, migrate normally
- CONFIG_NR_DRAM_BANKS_MAX was defined and then used for
  CONFIG_NR_DRAM_BANKS after a check, just migrate it over now.
- CONFIG_NR_DRAM_BANKS was very oddly defined on p2771-0000-* (to 1024 +
  2), set this to 8.

Signed-off-by: Tom Rini

Convert all of CONFIG_CONS_INDEX to Kconfig

2018-03-16T14:28:52+00:00

This converts the following to Kconfig:
   CONFIG_CONS_INDEX

We have existing entries for this option in a number of places, with
different guards on them.  They're also sometimes used for things not
directly inside of the serial driver.  First, introduce a new symbol to
guard the use of CONFIG_CONS_INDEX, so that in the case where we don't
need this for the serial driver, but for some other use, we can still do
it.  Next, consolidate all of these into the single entry in
drivers/serial/Kconfig.  Finally, introduce CONS_INDEX_[023456] so that
we can imply a correct value here to make the defconfig side of this
smaller.

Signed-off-by: Adam Ford 
[trini: Rework a lot of the logic here, such that I took authorship from
Adam, but kept his S-o-B line]
Signed-off-by: Tom Rini

Kconfig: cmd: Make networking command dependent on NET

2018-02-27T21:25:30+00:00

Enable networking command only when NET is enabled.
And remove selecting NET for CMD_NET

Signed-off-by: Michal Simek 
Signed-off-by: Tom Rini

Convert CONFIG_BOOTP_BOOTPATH et al to Kconfig

2018-02-24T02:41:49+00:00

This converts the following to Kconfig:
   CONFIG_BOOTP_BOOTPATH
   CONFIG_BOOTP_DNS
   CONFIG_BOOTP_GATEWAY
   CONFIG_BOOTP_HOSTNAME
   CONFIG_BOOTP_PXE
   CONFIG_BOOTP_SUBNETMASK
   CONFIG_CMDLINE_EDITING
   CONFIG_AUTO_COMPLETE
   CONFIG_SYS_LONGHELP
   CONFIG_SUPPORT_RAW_INITRD
   CONFIG_ENV_VARS_UBOOT_CONFIG

Signed-off-by: Adam Ford 
[trini: Re-run the migration]
Signed-off-by: Tom Rini

configs: Migrate CONFIG_SYS_TEXT_BASE

2018-02-11T14:30:09+00:00

On the NIOS2 and Xtensa architectures, we do not have
CONFIG_SYS_TEXT_BASE set.  This is a strict migration of the current
values into the defconfig and removing them from the headers.

I did not attempt to add more default values in and for now will leave
that to maintainers.

Signed-off-by: Tom Rini

cmd: Toggle the default value of CONFIG_CMD_IMLS

2017-10-10T21:51:04+00:00

Having this as a 'default y' is rather annoying because it doesn't
actually compile unless other options are defined in the board header:

../cmd/bootm.c: In function 'do_imls_nor':
../cmd/bootm.c:330:7: error: 'CONFIG_SYS_MAX_FLASH_BANKS' undeclared (first use in this function); did you mean 'CONFIG_SYS_MAX_FLASH_SECT'?
   i < CONFIG_SYS_MAX_FLASH_BANKS; ++i, ++info) {

Make it 'default n' so people who develop new boards that start from a
blank defconfig have one less compilation failure to debug.

Signed-off-by: Tuomas Tynkkynen

configs: Resync with savedefconfig

2017-08-28T11:16:32+00:00

Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini

common: Move CONFIG_BOOTARGS to Kconfig

2017-08-14T21:06:06+00:00

Also introduce CONFIG_USE_BOOTARGS option so we can control if
CONFIG_BOOTARGS defined at all.

Signed-off-by: Sam Protsenko 
[trini: Resync r8a779[56]_ulcb, various ls10xx targets]
Signed-off-by: Tom Rini