u-boot.git/configs/coreboot_defconfig, branch master

coreboot: make use of smbios parser

2020-11-05T06:58:45+00:00

If u-boot gets used as coreboot payload it might be nice to get
vendor, model and bios version from smbios. I am not sure about
the output of all the read information.

With qemu target for coreboot this could look this:

CBFS: Found @ offset 14f40 size 3b188
Checking segment from ROM address 0xffc15178
Checking segment from ROM address 0xffc15194
Loading segment from ROM address 0xffc15178
  code (compression=1)
  New segment dstaddr 0x01110000 memsize 0x889ef srcaddr 0xffc151b0 filesize 0x3b150
Loading Segment: addr: 0x01110000 memsz: 0x00000000000889ef filesz: 0x000000000003b150
using LZMA
Loading segment from ROM address 0xffc15194
  Entry Point 0x01110000
BS: BS_PAYLOAD_LOAD run times (exec / console): 77 / 1 ms
Jumping to boot code at 0x01110000(0x07fa7000)

U-Boot 2020.10-00536-g5dcf7cc590-dirty (Oct 07 2020 - 14:21:51 +0200)

CPU: x86_64, vendor AMD, device 663h
DRAM:  127.1 MiB
MMC:
Video: No video mode configured in coreboot!
Video: No video mode configured in coreboot!
Vendor: QEMU
Model: Standard PC (i440FX + PIIX, 1996)
Bios Version: 4.12-3152-g326a499f6f-dirty
Net:   e1000: 52:54:00:12:34:56
       eth0: e1000#0
No working controllers found
Finalizing coreboot
Hit any key to stop autoboot:  0

Signed-off-by: Christian Gmeiner 
Reviewed-by: Bin Meng

configs: Resync with savedefconfig

2020-08-10T19:31:07+00:00

Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini

Convert CONFIG_ENV_OVERWRITE to Kconfig

2020-07-28T20:18:06+00:00

This converts the following to Kconfig:
   CONFIG_ENV_OVERWRITE

Signed-off-by: Adam Ford 
[trini: Rerun migration, remove some comments]
Signed-off-by: Tom Rini

configs: Resync with savedefconfig

2020-07-28T12:46:52+00:00

Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini

Convert CONFIG_BZIP2 et al to Kconfig

2020-06-04T22:10:02+00:00

This converts the following to Kconfig:
   CONFIG_BZIP2
   CONFIG_GZIP
   CONFIG_LZO
   CONFIG_ZLIB
   CONFIG_LZMA
   CONFIG_LZO

Signed-off-by: Tom Rini

configs: Resync with savedefconfig

2019-12-04T22:18:38+00:00

Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini

env: Finish migration of common ENV options

2019-11-20T23:32:09+00:00

- In ARMv8 NXP Layerscape platforms we also need to make use of
  CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so.
- On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define
  to 0.
- Add Kconfig entry for ENV_ADDR.
- Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it.
- Add ENV_xxx_REDUND options that depend on their primary option and
  SYS_REDUNDAND_ENVIRONMENT
- On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR
  for the pre-main-U-Boot environment location.
- On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but
  rather it being non-zero, as it will now be zero by default.
- Rework the env_offset absolute in env/embedded.o to not use
  CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within
  ENV_IS_IN_FLASH.
- Migrate all platforms.

Cc: Wolfgang Denk 
Cc: Joe Hershberger 
Cc: Patrick Delaunay 
Cc: uboot-stm32@st-md-mailman.stormreply.com
Signed-off-by: Tom Rini 
Acked-by: Joe Hershberger 
Reviewed-by: Simon Goldschmidt

env: Add CONFIG_SYS_RELOC_GD_ENV_ADDR symbol

2019-11-20T17:24:50+00:00

Today in initr_reloc_global_data() we use some non-obvious tests to
determine if we need to relocate the env_addr within gd or not.  In
order to facilitate migration of other symbols to Kconfig we need to
introduce a new symbol for this particular use case.

Cc: Wolfgang Denk 
Cc: Joe Hershberger 
Signed-off-by: Tom Rini

configs: Resync with savedefconfig

2019-09-23T15:47:37+00:00

Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini

Convert CONFIG_SHOW_BOOT_PROGRESS to Kconfig

2019-08-02T15:17:58+00:00

This converts the following to Kconfig:
   CONFIG_SHOW_BOOT_PROGRESS

Signed-off-by: Simon Glass