u-boot.git/common/cmd_pci.c, branch v2011.03

pci: Clean up PCI info when CONFIG_PCI_SCAN_SHOW

2010-11-14T22:46:46+00:00

This change does the following:
- Removes the printing of the PCI interrupt line value.  This is
  normally set to 0 by U-Boot on bootup and is rarely used during
  everyday operation.

- Prints out the PCI function number of a device.  Previously a device
  with multiple functions would be printed identically 2 times, which is
  generally confusing.  For example, on an Intel 2 port gigabit Ethernet
  card the following was displayed:
    ...
    04  01  8086  1010  0200  00
    04  01  8086  1010  0200  00
    ...

- Prints a text description of each device's PCI class instead of the
  raw PCI class code.  The textual description makes it much easier to
  determine what devices are installed on a PCI bus.

- Changes the general formatting of the PCI device output.

Previous output:
  PCIE1: connected as Root Complex
          04  01  8086  1010  0200  00
          04  01  8086  1010  0200  00
          03  00  10b5  8112  0604  00
          02  01  10b5  8518  0604  00
          02  02  10b5  8518  0604  00
          08  00  1957  0040  0b20  00
          07  00  10b5  8518  0604  00
          09  00  10b5  8112  0604  00
          07  01  10b5  8518  0604  00
          07  02  10b5  8518  0604  00
          06  00  10b5  8518  0604  00
          02  03  10b5  8518  0604  00
          01  00  10b5  8518  0604  00
  PCIE1: Bus 00 - 0b
  PCIE2: connected as Root Complex
          0d  00  1957  0040  0b20  00
  PCIE2: Bus 0c - 0d

Updated output:
  PCIE1: connected as Root Complex
          04:01.0 - 8086:1010 - Network controller
          04:01.1 - 8086:1010 - Network controller
          03:00.0 - 10b5:8112 - Bridge device
          02:01.0 - 10b5:8518 - Bridge device
          02:02.0 - 10b5:8518 - Bridge device
          08:00.0 - 1957:0040 - Processor
          07:00.0 - 10b5:8518 - Bridge device
          09:00.0 - 10b5:8112 - Bridge device
          07:01.0 - 10b5:8518 - Bridge device
          07:02.0 - 10b5:8518 - Bridge device
          06:00.0 - 10b5:8518 - Bridge device
          02:03.0 - 10b5:8518 - Bridge device
          01:00.0 - 10b5:8518 - Bridge device
  PCIE1: Bus 00 - 0b
  PCIE2: connected as Root Complex
          0d:00.0 - 1957:0040 - Processor
  PCIE2: Bus 0c - 0d

Signed-off-by: Peter Tyser

pci: Add ability to re-enumerate PCI buses

2010-10-22T07:17:12+00:00

Add a new 'pci enum' command which re-enumerates the PCI buses.  This
command is enabled via the CONFIG_CMD_PCI_ENUM define and can be useful
in boards with FPGAs connected via PCI/PCIe, boards that support PCI
hot-plugging, or during PCI debug.

Also enable the 'pci enum' command for X-ES's Freescale-based boards.

Signed-off-by: John Schmoller 
Signed-off-by: Peter Tyser 
Acked-by: Kumar Gala 
Acked-by: Wolfgang Denk

cmd_usage(): simplify return code handling

2010-07-24T18:43:57+00:00

Lots of code use this construct:

	cmd_usage(cmdtp);
	return 1;

Change cmd_usage() let it return 1 - then we can replace all these
ocurrances by

	return cmd_usage(cmdtp);

This fixes a few places with incorrect return code handling, too.

Signed-off-by: Wolfgang Denk

Make sure that argv[] argument pointers are not modified.

2010-07-04T21:55:42+00:00

The hush shell dynamically allocates (and re-allocates) memory for the
argument strings in the "char *argv[]" argument vector passed to
commands.  Any code that modifies these pointers will cause serious
corruption of the malloc data structures and crash U-Boot, so make
sure the compiler can check that no such modifications are being done
by changing the code into "char * const argv[]".

This modification is the result of debugging a strange crash caused
after adding a new command, which used the following argument
processing code which has been working perfectly fine in all Unix
systems since version 6 - but not so in U-Boot:

int main (int argc, char **argv)
{
	while (--argc > 0 && **++argv == '-') {
/* ====> */	while (*++*argv) {
			switch (**argv) {
			case 'd':
				debug++;
				break;
			...
			default:
				usage ();
			}
		}
	}
	...
}

The line marked "====>" will corrupt the malloc data structures and
usually cause U-Boot to crash when the next command gets executed by
the shell.  With the modification, the compiler will prevent this with
an
	error: increment of read-only location '*argv'

N.B.: The code above can be trivially rewritten like this:

	while (--argc > 0 && **++argv == '-') {
		char *arg = *argv;
		while (*++arg) {
			switch (*arg) {
			...

Signed-off-by: Wolfgang Denk 
Acked-by: Mike Frysinger

General help message cleanup

2009-06-12T18:47:16+00:00

Many of the help messages were not really helpful; for example, many
commands that take no arguments would not print a correct synopsis
line, but "No additional help available." which is not exactly wrong,
but not helpful either.

Commit ``Make "usage" messages more helpful.'' changed this
partially. But it also became clear that lots of "Usage" and "Help"
messages (fields "usage" and "help" in struct cmd_tbl_s respective)
were actually redundant.

This patch cleans this up - for example:

Before:
	=> help dtt
	dtt - Digital Thermometer and Thermostat

	Usage:
	dtt         - Read temperature from digital thermometer and thermostat.

After:
	=> help dtt
	dtt - Read temperature from Digital Thermometer and Thermostat

	Usage:
	dtt

Signed-off-by: Wolfgang Denk

Command usage cleanup

2009-01-28T07:49:52+00:00

Remove command name from all command "usage" fields and update
common/command.c to display "name - usage" instead of
just "usage". Also remove newlines from command usage fields.

Signed-off-by: Peter Tyser

Standardize command usage messages with cmd_usage()

2009-01-28T07:43:45+00:00

Signed-off-by: Peter Tyser

rename CFG_ macros to CONFIG_SYS

2008-10-18T19:54:03+00:00

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD

move cmd_get_data_size to command.c

2008-09-10T20:48:05+00:00

add CMD_DATA_SIZE macro to enable it

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD

Big white-space cleanup.

2008-05-20T22:14:08+00:00

This commit gets rid of a huge amount of silly white-space issues.
Especially, all sequences of SPACEs followed by TAB characters get
removed (unless they appear in print statements).

Also remove all embedded "vim:" and "vi:" statements which hide
indentation problems.

Signed-off-by: Wolfgang Denk