Add the missing dependency for the command ums:
- CONFIG_BLK: call of blk_* functions in usb_mass_storage.c
- CONFIG_USB_GADGET: required to select CONFIG_USB_FUNCTION_MASS_STORAGE

Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>

This patch adds a new "extension" command, which aims at detecting
extension boards connected to the hardware platform, and apply the
Device Tree overlays that describe the hardware present on those
extension boards.

In order to enable this mechanism, board-specific code must implement
the extension_board_scan() function that fills in a linked list of
"struct extension", each describing one extension board. In addition,
the board-specific code must select the SUPPORT_EXTENSION_SCAN Kconfig
boolean.

Based on this:

 - "extension scan" makes the generic code call the board-specific
   extension_board_scan() function to retrieve the list of detected
   extension boards.

 - "extension list" allows to list the detected extension boards.

 - "extension apply <number>|all" allows to apply the Device Tree
   overlay(s) corresponding to one, or all, extension boards

The latter requires two environment variables to exist and set one variable
to run:

 - extension_overlay_addr: the RAM address where to load the Device
   Tree overlays

 - extension_overlay_cmd: the U-Boot command to load one overlay.
   Indeed, the location and mechanism to load DT overlays is very setup
   specific.

 - extension_overlay_name: set by the command: the name of the DT which
   will be load during the execution.

When calling the command described in the extension_overlay_cmd
variable, the variable extension_overlay_name will be defined. So a
typical extension_overlay_cmd will look like this:

  extension_overlay_cmd=load mmc 0:1 $extension_overlay_addr /boot/$extension_overlay_name

Here is an example on how to use it:
=> run loadfdt
=> fdt addr $fdtaddr
=> setenv extension_overlay_addr 0x1000
=> setenv extension_overlay_cmd 'load mmc 0:1 ${extension_overlay_addr} /boot/${extension_overlay_name}'
=> extension scan
Found 1 extension board(s).
=> extension apply 0
519 bytes read in 3 ms (168.9 KiB/s)

Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Reviewed-by: Maxime Ripard <maxime@cerno.tech>

Add support for stack protector for UBOOT, SPL, and TPL
as well as new pytest for stackprotector

Signed-off-by: Joel Peshkin <joel.peshkin@broadcom.com>

Adjust UEFI build flags.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>

Trying to compile with CONFIG_CMD_MMC=y and CONFIG_MMC=n leads to errors:

riscv64-linux-gnu-ld.bfd: cmd/built-in.o: in function `do_mmcops':
cmd/mmc.c:984: undefined reference to `get_mmc_num'
riscv64-linux-gnu-ld.bfd: cmd/built-in.o: in function `do_mmc_setdsr':
cmd/mmc.c:873: undefined reference to `find_mmc_device'

Add missing dependency.

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>

This variable is a boolean, not a string.

Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>

 This patch enable blob command for mScale platforms.

Signed-off-by: Aymen Sghaier <aymen.sghaier@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>

Signed-off-by: Franck LENORMAND <franck.lenormand@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>

In order to build CMD_BLOB on i.MX CAAM supported devices it's
necessary to select IMX_HAB. Add IMX_HAB and CAAM supported
SoCs as dependency.

Signed-off-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>

The usb command cannot be compiled with CONFIG_USB=n:

ld.bfd: cmd/usb.c:660: undefined reference to `usb_stop'
ld.bfd: cmd/usb.c:663: undefined reference to `usb_started'

Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>