u-boot.git/board, branch v2009.06

85xx: Add UART1 support for MPC8569MDS

2009-06-12T05:11:10+00:00

MPC8569 UART1 signals are muxed with PortF bit[9-12], we need to define
those pins before using UART1.

Signed-off-by: Haiying Wang 
Signed-off-by: Kumar Gala

EP88x: fix broken linker script

2009-06-09T21:10:01+00:00

Signed-off-by: Wolfgang Denk 
Tested-by: Mikhail Zaturenskiy

85xx: Fix the wrong BCSR address of 8569MDS

2009-06-09T20:58:32+00:00

The BCSR17[7] = 1 will unlock the write protect of FLASH.
The WP# pin only controls the write protect of top/bottom sector,
That is why we can save env, but we can't write the first sector
before the patch.

Signed-off-by: Dave Liu

85xx: Fix the clock adjust of mpc8569mds board

2009-06-09T20:58:05+00:00

Currently the clk_adj is 6 (3/4 cycle), The settings will cause
the DDR controller hang at the data init. Change the clk_adj
from 6 to 4 (1/2 cycle), make the memory system stable.

Signed-off-by: Dave Liu

Add config option for disabling DM9000-SROM support.

2009-06-09T05:57:21+00:00

Some boards do not have SROM support for the DM9000 network adapter.
Instead of listing these board names in the driver code, make this
option configurable from the board config file.

It also removes a build warning for the at91sam9261ek board:
'dm9000x.c:545: warning: 'read_srom_word' defined but not used'

And it repaires the trizepsiv board build which was broken around the
same routines

Signed-off-by: Remy Bohmer 
Signed-off-by: Ben Warren

Redundant Environment: protect full sector size

2009-06-03T22:16:16+00:00

Several boards used different ways to specify the size of the
protected area when enabling flash write protection for the sectors
holding the environment variables: some used CONFIG_ENV_SIZE and
CONFIG_ENV_SIZE_REDUND, some used CONFIG_ENV_SECT_SIZE, and some even
a mix of both for the "normal" and the "redundant" areas.

Normally, this makes no difference at all. However, things are
different when you have to deal with boards that can come with
different types of flash chips, which may have different sector
sizes.

Here we may have to chose CONFIG_ENV_SECT_SIZE such that it fits the
biggest sector size, which may include several sectors on boards using
the smaller sector flash types. In such a case, using CONFIG_ENV_SIZE
or CONFIG_ENV_SIZE_REDUND to enable the protection may lead to the
case that only the first of these sectors get protected, while the
following ones aren't.

This is no real problem, but it can be confusing for the user -
especially on boards that use CONFIG_ENV_SECT_SIZE to protect the
"normal" areas, while using CONFIG_ENV_SIZE_REDUND for the
"redundant" area.

To avoid such inconsistencies, I changed all sucn boards that I found
to consistently use CONFIG_ENV_SECT_SIZE for protection. This should
not cause any functional changes to the code.

Signed-off-by: Wolfgang Denk 
Cc: Paul Ruhland
Cc: Pantelis Antoniou 
Cc: Stefan Roese 
Cc: Gary Jennejohn 
Cc: Dave Ellis 
Acked-by: Stefan Roese

Blackfin: bf518f-ezbrd: setup portmux for async flash

2009-05-26T02:38:42+00:00

The pins for async memory where parallel flash lives are not enabled by
default, so make sure we mux them as needed.

Signed-off-by: Graf Yang 
Signed-off-by: Mike Frysinger

Minor Coding Style fix; update CHANGELOG.

2009-05-15T20:32:57+00:00

Signed-off-by: Wolfgang Denk

Fix e-mail address of Gary Jennejohn.

2009-05-15T20:11:59+00:00

Signed-off-by: Detlev Zundel

powerpc/inka4x0: Remove left-over ide reset code.

2009-05-15T19:31:24+00:00

The pin which was used in preliminary versions of the board for ide
reset is really connected to the rtc clock.

Signed-off-by: Detlev Zundel