Move this out of the common header and include it only where needed.  In
a number of cases this requires adding "struct udevice;" to avoid adding
another large header or in other cases replacing / adding missing header
files that had been pulled in, very indirectly.   Finally, we have a few
cases where we did not need to include <asm/global_data.h> at all, so
remove that include.

Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>

The Linux coding style guide (Documentation/process/coding-style.rst)
clearly says:

  It's a **mistake** to use typedef for structures and pointers.

Besides, using typedef for structures is annoying when you try to make
headers self-contained.

Let's say you have the following function declaration in a header:

  void foo(bd_t *bd);

This is not self-contained since bd_t is not defined.

To tell the compiler what 'bd_t' is, you need to include <asm/u-boot.h>

  #include <asm/u-boot.h>
  void foo(bd_t *bd);

Then, the include direcective pulls in more bloat needlessly.

If you use 'struct bd_info' instead, it is enough to put a forward
declaration as follows:

  struct bd_info;
  void foo(struct bd_info *bd);

Right, typedef'ing bd_t is a mistake.

I used coccinelle to generate this commit.

The semantic patch that makes this change is as follows:

  <smpl>
  @@
  typedef bd_t;
  @@
  -bd_t
  +struct bd_info
  </smpl>

Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>

Move this uncommon header out of the common header.

Signed-off-by: Simon Glass <sjg@chromium.org>

Move this uncommon header out of the common header.

Signed-off-by: Simon Glass <sjg@chromium.org>

Move this header out of the common header. Network support is used in
quite a few places but it still does not warrant blanket inclusion.

Note that this net.h header itself has quite a lot in it. It could be
split into the driver-mode support, functions, structures, checksumming,
etc.

Signed-off-by: Simon Glass <sjg@chromium.org>

The PFUZE100 and PFUZE200 PMICs can be discerned by bit 0 in DeviceID
register. Print the correct identification of the PMICs.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Silvio Fricke <silvio.fricke@softing.com>
Cc: Stefano Babic <sbabic@denx.de>

Simplify the uSDHC4 eMMC controller setup. This is the only eMMC
present on the system and only controller that is used, so drop
the extra logic.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Silvio Fricke <silvio.fricke@softing.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>

The board has both VDD_SOC_IN and VDD_ARM_IN rails connected to the same
PMIC rail, align the LDO voltages to avoid leaking inside the MX6SX SoC.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Silvio Fricke <silvio.fricke@softing.com>
Cc: Stefano Babic <sbabic@denx.de>

Ever since the conversion to DM PCI, the board was missing the PCIe DT
nodes, hence the PCI did not really work. Fill in the DT nodes and add
missing PCIe device reset.

Moreover, bring the PCIe power domain up before booting Linux. This is
mandatory to keep old broken vendor kernels working, as they do not do
so and depend on the bootloader to bring the power domain up.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Silvio Fricke <silvio.fricke@softing.com>
Cc: Stefano Babic <sbabic@denx.de>

Convert the board to ethernet DM support. Adjust board file accordingly,
as the board_eth_init() contains custom clock configuration required for
this board to work. Furthermore, enable FEC1 clock to make FEC1 work as
well.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Silvio Fricke <silvio.fricke@softing.com>
Cc: Stefano Babic <sbabic@denx.de>