u-boot.git/board/raspberrypi, branch master

rpi: Add identifier for the new CM4

2021-02-18T10:56:25+00:00

The Raspberry Pi Foundation released the new Compute Module 4 which we
want to detect, so we can enable Ethernet on it and know the correct
device tree file name.

Note that this sets the Ethernet option to true since the official CM4
IO board has an Ethernet port. But that might not be the case when using
custom ones.

Signed-off-by: Nicolas Saenz Julienne 
Reviewed-by: Peter Robinson 
Tested-by: Peter Robinson 
Signed-off-by: Matthias Brugger

rpi: Add identifier for the new RPi400

2021-02-18T10:56:25+00:00

The Raspberry Pi Foundation released the new RPi400 which we want to
detect, so we can enable Ethernet on it and know the correct device tree
file name.

Signed-off-by: Nicolas Saenz Julienne 
Reviewed-by: Peter Robinson 
Tested-by: Peter Robinson 
Signed-off-by: Matthias Brugger

rpi: limit size of the RAM to the multiple of the MMU_SECTION_SIZE

2021-02-18T10:56:25+00:00

When RPi4 is booted from USB Mass Storage, the firmware reports 947MiB of
the ARM memory (948 in case of the standard SD-card boot). This value is
not MMU_SECTION_SIZE aligned, so the dram_bank_mmu_setup() skips mapping
of the last 1MiB. This later causes u-boot in ARM 32bit mode to freeze,
because it relocated itself into that unmapped memory and fails to
execute.

Fix this by limiting the size of the first bank to the multiple of
MMU_SECTION_SIZE.

Signed-off-by: Marek Szyprowski 
Reviewed-by: Nicolas Saenz Julienne 
Tested-by: Jaehoon Chung 
Reviewed-by: Jaehoon Chung 
Signed-off-by: Matthias Brugger

treewide: convert bd_t to struct bd_info by coccinelle

2020-07-17T13:30:13+00:00

The Linux coding style guide (Documentation/process/coding-style.rst)
clearly says:

  It's a **mistake** to use typedef for structures and pointers.

Besides, using typedef for structures is annoying when you try to make
headers self-contained.

Let's say you have the following function declaration in a header:

  void foo(bd_t *bd);

This is not self-contained since bd_t is not defined.

To tell the compiler what 'bd_t' is, you need to include 

  #include 
  void foo(bd_t *bd);

Then, the include direcective pulls in more bloat needlessly.

If you use 'struct bd_info' instead, it is enough to put a forward
declaration as follows:

  struct bd_info;
  void foo(struct bd_info *bd);

Right, typedef'ing bd_t is a mistake.

I used coccinelle to generate this commit.

The semantic patch that makes this change is as follows:

  
  @@
  typedef bd_t;
  @@
  -bd_t
  +struct bd_info
  

Signed-off-by: Masahiro Yamada

efi_loader: round the memory area in efi_add_memory_map()

2020-05-17T19:59:53+00:00

Virtually all callers of this function do the rounding on their own.
Some do it right, some don't. Instead of doing this in each caller,
do the rounding in efi_add_memory_map(). Change the size parameter
to bytes instead of pages and remove aligning and size calculation in
all callers.

There is no more need to make the original efi_add_memory_map() (which
takes pages as size) available outside the module. Thus rename it to
efi_add_memory_map_pg() and make it static to prevent further misuse
outside the module.

Signed-off-by: Michael Walle 
Add missing comma in sunxi_display.c.
Reviewed-by: Heinrich Schuchardt

rpi: use the newly-added RPI_EFI_NR_SPIN_PAGES

2020-05-13T12:04:50+00:00

Some systems may use a slightly larger stub to do PSCI for booting the RPi
family.  The number of pages has been made configurable so that operating
systems building U-Boot for use in these kinds of environments can reserve
more memory in the EFI memory map.

Signed-off-by: Kyle Evans 
Signed-off-by: Matthias Brugger

rpi: Kconfig option for initial page reservation

2020-05-13T12:04:49+00:00

While the nearly-universal default for the Raspberry Pi family is to use
spin tables and the spin table implementation provided by the Raspberry Pi
Foundation, FreeBSD and others may use a PSCI implementation instead.

Accommodate these setups by allowing them to configure for more than one
page to be reserved in the initial reservation.  The default reservation
remains as one page.

Signed-off-by: Kyle Evans 
Signed-off-by: Matthias Brugger

rpi: Enable DRAM bank initialization on arm64

2019-12-11T09:14:12+00:00

Up to now we only update the DRAM banks when we are define
CONFIG_BCM2711. But our one binary approach uses a config that supports
BCM2837 and BCM2711. As a result we only see one gibibyte of RAM on
Raspberry Pi 4, even if it has more RAM.
Fix this by calling dram_init_banksize.

Fixes: 5694090670 ("ARM: defconfig: add unified config for RPi3 and RPi4")

Signed-off-by: Matthias Brugger

rpi: fix dram bank initialization

2019-12-11T09:14:12+00:00

To update the dram bank information from device-tree we use
fdtdec_decode_ram_size() which expectes the the size-cells and
address-cells to be defined in the memory node. For normal system RAM
these values are defined in the root node. When the values differ from
the default values defined in the spec, we can end up with wrong RAM
bank information.

Switch to the "standard" way to update the RAM bank information to
avoid this.

Fixes: 9de5b89e4c ("rpi4: enable dram bank initialization")

Signed-off-by: Matthias Brugger

common: Move board_get_usable_ram_top() out of common.h

2019-12-02T23:25:04+00:00

Move this function into init.h which seems to be designed for this sort
of thing. Also update the header to declare struct global_data so that it
can be included without global_data.h being needed.

Signed-off-by: Simon Glass 
Reviewed-by: Tom Rini