u-boot.git/board/mpc8540eval/mpc8540eval.c, branch v2009.06

85xx: Fix compile breakage with MPC8540EVAL

2009-01-28T20:01:52+00:00

Configuring for MPC8540EVAL board...
mpc8540eval.c: In function 'checkboard':
mpc8540eval.c:53: error: invalid operands to binary /
make[1]: *** [mpc8540eval.o] Error 1

Signed-off-by: Kumar Gala

mpc8xxx: LCRR[CLKDIV] is sometimes five bits

2008-12-20T00:20:25+00:00

On newer CPUs, 8536, 8572, and 8610, the CLKDIV field of LCRR is five bits
instead of four.

In order to avoid an ifdef, LCRR_CLKDIV is set to 0x1f on all systems.  It
should be safe as the fifth bit was defined as reserved and set to 0.

Code that was using a hard coded 0x0f is changed to use LCRR_CLKDIV.

Signed-off-by: Trent Piepho 
Acked-by: Kumar Gala 
Acked-by: Jon Loeliger

Cleanup: fix "MHz" spelling

2008-10-21T09:25:39+00:00

Signed-off-by: Wolfgang Denk

rename CFG_ macros to CONFIG_SYS

2008-10-18T19:54:03+00:00

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD

Moved initialization of TULIP Ethernet controller to board_eth_init()

2008-09-03T04:18:18+00:00

Affected boards:
	cu824
	bab7xx
	adciop
	dasa_sim
	mousse
	mpc8540eval
	musenki
	mvblue
	pcippc2/pcippc6
	sbc8240
	stxssa

Removed initialization of the driver from net/eth.c

Signed-off-by: Ben Warren

FSL DDR: Convert MPC8540EVAL to new DDR code.

2008-08-27T16:43:52+00:00

Signed-off-by: Kumar Gala

Change initdram() return type to phys_size_t

2008-06-12T06:50:18+00:00

This patch changes the return type of initdram() from long int to phys_size_t.
This is required for a couple of reasons: long int limits the amount of dram
to 2GB, and u-boot in general is moving over to phys_size_t to represent the
size of physical memory.  phys_size_t is defined as an unsigned long on almost
all current platforms.

This patch *only* changes the return type of the initdram function (in
include/common.h, as well as in each board's implementation of initdram).  It
does not actually modify the code inside the function on any of the platforms;
platforms which wish to support more than 2GB of DRAM will need to modify
their initdram() function code.

Build tested with MAKEALL for ppc, arm, mips, mips-el. Booted on powerpc
MPC8641HPCN.

Signed-off-by: Becky Bruce

Remove erroneous or extra spd.h #includers.

2008-03-04T23:17:43+00:00

Many of the spd.h #includers don't need it,
and wanted to have spd_sdram() declared instead.
Since they didn't get that, some also had open
coded extern declarations of it instead or as well.
Fix it all up by using spd_sdram.h where needed.

Signed-off-by: Jon Loeliger

Stop using immap_t on 85xx

2007-12-12T04:34:20+00:00

In the future the offsets to various blocks may not be in same location.
Move to using CFG_MPC85xx_*_ADDR as the base of the registers
instead of getting it via &immap.

Signed-off-by: Kumar Gala

Stop using immap_t for guts offset on 85xx

2007-12-12T04:34:19+00:00

In the future the offsets to various blocks may not be in same location.
Move to using CFG_MPC85xx_GUTS_ADDR as the base of the guts registers
instead of getting it via &immap->im_gur.

Signed-off-by: Kumar Gala