u-boot.git/board/firefly, branch master

common: Drop asm/global_data.h from common header

2021-02-02T20:33:42+00:00

Move this out of the common header and include it only where needed.  In
a number of cases this requires adding "struct udevice;" to avoid adding
another large header or in other cases replacing / adding missing header
files that had been pulled in, very indirectly.   Finally, we have a few
cases where we did not need to include  at all, so
remove that include.

Signed-off-by: Simon Glass 
Signed-off-by: Tom Rini

rockchip: firefly-rk3288: Fix the code support for SPL_LED

2020-08-21T11:56:19+00:00

Fix the build error for the wrong code when CONFIG_SPL_LED is enabled.

Signed-off-by: Kever Yang

rockchip: roc-rk3399-pc: Set LED only during POR and pwr_key=y

2020-07-22T12:55:13+00:00

ROC-RK3399-PC has specific set of configurations for
on-board led setup.

Due to easiness for user to know the state of the board
roc-rk339-pc board code will setup the low power led
on/off, and waiting for user to press power key and then
glow full power led.

All this needs to happen only during power-on-reset not
for soft reset or WDT.

Also, it is not a proper usage to ask the user to press
the Power key if the board connected remotely, so add
the environment variable 'pwr_key' to check as well.

So, user need to press Power key only
- during POR
- pwr_key=y

Tested-by: Suniel Mahesh 
Signed-off-by: Jagan Teki 
Reviewed-by: Kever Yang

rockchip: roc-rk3399-pc: Add custom led_setup()

2020-07-22T12:55:13+00:00

roc-rk3399-pc has some specific requirements to support LEDS,
environment. board detection and etc prior to U-Boot proper.

So as of now SPL would be a better stage for these custom board
requirements to support unlike TPL. Adding few of these custom
requirements like LEDS in TPL would require extra code pulling
and also the size of TPL can grow.

So, this patch moves the leds code from TPL into SPL Board init
led_setup code.

Signed-off-by: Jagan Teki 
Reviewed-by: Kever Yang 
(split tpl.c change as separate patch)
Signed-off-by: Kever Yang

common: Drop linux/bitops.h from common header

2020-05-19T01:19:23+00:00

Move this uncommon header out of the common header.

Signed-off-by: Simon Glass

common: Drop log.h from common header

2020-05-19T01:19:18+00:00

Move this header out of the common header.

Signed-off-by: Simon Glass

rk3399: Add ROC-RK3399-PC Mezzanine board

2020-05-01T10:32:56+00:00

Add Firefly ROC-RK3399-PC Mezzanine board which is an
extension board on top of roc-rk3399-pc.

Will drop the separate defconfig file, once we support
the board detection at runtime.

Signed-off-by: Suniel Mahesh 
Signed-off-by: Jagan Teki 
Reviewed-by: Kever Yang

rockchip: board: roc-pc-rk3399: Remove support for push button

2020-04-29T02:30:55+00:00

In case of a power interruption, human intervention is required which
is not desirable if the device is installed at a remote location. Drop
yellow LED as it is not much of use. Keep red LED(diy-led) as it is, to
indicate board in full power mode.

Signed-off-by: Suniel Mahesh 
Reviewed-by: Kever Yang

board: roc-pc-rk3399: Add support for onboard LED's and push button to indicate power mode

2020-02-19T08:45:38+00:00

Added support for onboard LED's and push button. When powered board will be
in low power mode(yellow LED), on button press, board enters full power mode
(red LED) and boots u-boot.

Signed-off-by: Suniel Mahesh 
Reviewed-by: Kever Yang

rockchip: rk3399: split roc-pc-rk3399 out of evb_rk3399

2020-02-19T08:45:38+00:00

roc-pc-rk3399 board has one user button & three user LED's. Currently
we don't have any code support for these devices. Since button and LED's are
specific to roc-pc-rk3399 board, split it into its own board file and add code
support here.

Signed-off-by: Suniel Mahesh 
Reviewed-by: Kever Yang