u-boot.git/board/amlogic, branch master

arm: meson: remove static ethernet link setup

2021-04-06T09:10:29+00:00

The static ethernet link type config code is no more needed because now handled by
the meson8b glue driver, delete it.

Signed-off-by: Neil Armstrong

Merge branch '2021-02-02-drop-asm_global_data-when-unused'

2021-02-15T15:16:45+00:00

- Merge the patch to take  out of

board: amlogic: odroid: add runtime detection of the N2/N2+/C4/HC4 variants

2021-02-10T09:00:51+00:00

Use the ADC channel 1 to check the hardware revision of the board and
detect the N2 vs. N2+ and the C4 vs. HC4 variants. Each of them use
different dtb file, so adjust fdtfile environment variable to the
detected variant.

The ADC min/max values for each variant are taken from the vendor code,
adjusted to the 12-bit ADC driver operation mode (vendor code use 10-bit
mode).

Signed-off-by: Marek Szyprowski 
Reviewed-by: Jaehoon Chung 
Signed-off-by: Neil Armstrong

common: Drop asm/global_data.h from common header

2021-02-02T20:33:42+00:00

Move this out of the common header and include it only where needed.  In
a number of cases this requires adding "struct udevice;" to avoid adding
another large header or in other cases replacing / adding missing header
files that had been pulled in, very indirectly.   Finally, we have a few
cases where we did not need to include  at all, so
remove that include.

Signed-off-by: Simon Glass 
Signed-off-by: Tom Rini

board: amlogic: vim3: fix setup ethernet mac from efuse

2021-01-12T13:25:55+00:00

Fix reading built-in ethernet MAC address from efuse

NOTE: MAC is stored in ASCII format, 1bytes = 2characters by 0 offset

if mac from efuse not valid we use meson_generate_serial_ethaddr

NOTE: remake odroid-n2.c from Neil Armstrong 

Signed-off-by: Artem Lapkin 
[narmstrong: remove MAC print & spurious new endline]
Signed-off-by: Neil Armstrong

board: amlogic: add MMC boot device detection for environment load

2021-01-11T13:59:55+00:00

Detect eMMC or SD card boot on Odroid-C4/N2 and Khadas VIM3(l) boards and
report proper MMC device for the environment loading code. This allows to
automatically load and store environment variables on the FAT partition
or RAW offset of the MMC device without the need to use different
configurations on eMMC and SD card.

To use this feature with environment stored on FAT partition, one has to
specify an empty device part (i.e. ":1" for the first partition) in
CONFIG_ENV_FAT_DEVICE_AND_PART to let the code to set the device to the
value returned by mmc_get_env_dev() function.

Signed-off-by: Marek Szyprowski 
Reviewed-by: Jaehoon Chung 
Signed-off-by: Neil Armstrong

boards: amlogic: add Beelink S922X board family support

2021-01-11T13:59:54+00:00

Copied from Odroid N2. Add myself as maintainer.

Signed-off-by: Christian Hewitt 
Signed-off-by: Neil Armstrong

board: amlogic: vim3: read ethernet MAC address from efuse

2021-01-11T13:59:54+00:00

Add the board specific code for reading built-in ethernet MAC address
from efuse.

Signed-off-by: Marek Szyprowski 
Reviewed-by: Neil Armstrong 
Reviewed-by: Jaehoon Chung 
Tested-by: Jaehoon Chung 
Signed-off-by: Neil Armstrong

boards: amlogic: update documentation for WeTek Core2

2021-01-11T13:59:54+00:00

Update the device matrix and add build instructions.

Signed-off-by: Christian Hewitt 
[narmstrong: added wetek-core2.rst to q200 MAINTAINERS and added blank lines to fix build]
Signed-off-by: Neil Armstrong

boards: amlogic: add WeTek Core2 support

2021-01-11T13:59:54+00:00

Add a config for the WeTek Core2, largely based on the VIM2 config.

Signed-off-by: Christian Hewitt 
[narmstrong: added wetek-core2_defconfig to q200 MAINTAINERS]
Signed-off-by: Neil Armstrong