There is no reason not to use commong Kconfig by Microblaze too.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

Enable SPI drivers and driver model for microblaze.

Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

The Kconfig symbol CONFIG_STACK_SIZE is used both by ARM and Microblaze
with the same meaning. Move it to menu 'General setup' so that we can use
it for all architectures.

Use the value of CONFIG_STACK_SIZE instead of a hard coded 16 MiB value for
reserving memory in the UEFI sub-system.

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>

In a few places we have Kconfig entries that set SPL_LDSCRIPT to what is
the default value anyways.  Drop these.

Cc: Michal Simek <monstr@monstr.eu>
Cc: Rick Chen <rick@andestech.com>
Cc: Philippe Reynes <tremyfr@yahoo.fr>
Cc: Eric Jarrige <eric.jarrige@armadeus.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com> (for Microblaze)
Reviewed-by: Masahiro Yamada <masahiroy@kernel.org>

Setup initrd_high and fdt_high to be placed in lowmem space for kernel to
be able to reach it. Values are setup at run time to ensure that the same
setting can be used on different memory setup. Do this setting only when
variables are not

Similar run time detection was done for Zynqmp and Versal.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

CMD_DM is used for debug purpose and it shouldn't be enabled by default
via Kconfig. Unfortunately this is in the tree for quite a long time
that's why solution is to use imply DM for all targets which are
enabling DM.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>

Fix Kconfig bool, default, select and imply options to be
alphabetically sorted.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

There is no reason to save variables to flash only.
Select option via Kconfig instead.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

Converting GPIO to DM requires to do changes in reset subsystem
that's why support for Microblaze soft reset via sysreset and GPIO
sysreset support was added.
These two patches enables enabling GPIO DM.
Microblaze soft reset is bind at last reset method.

GPIO reset is handled via sysreset with adding this fragment to DT.

gpio-restart {
	compatible = "gpio-restart";
	gpios = <&reset_gpio 0 0 0>;
	/* 3rd cell ACTIVE_HIGH = 0, ACTIVE_LOW = 1 */
};

hard-reset-gpio property is not documented and also handled.
Conversion is required.

Unfortunately do_reset is required for SPL that's why use only soft
microblaze reset for now.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

With SPL_LDSCRIPT moved to Kconfig (and this being a 'string' config
node), all the lingering definitions in header files will cause
warnings/errors due to the redefinition of the configuration item.

As we don't want to pollute the defconfig files (and values should
usually be identical for entire architectures), the defaults are moved
into Kconfig.  Kconfig will always pick the first default that
matches, so please keep these values at the end of each file (to allow
any board-specific Kconfig, which will be included earlier) to
override with an unconditional default setting.

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>