u-boot.git/arch/arm/mach-imx/mx7ulp, branch master

caam: enable support for iMX7ULP

2021-04-08T07:18:29+00:00

Signed-off-by: Franck LENORMAND 
Signed-off-by: Peng Fan

reset: Remove addr parameter from reset_cpu()

2021-03-02T19:03:02+00:00

Historically, the reset_cpu() function had an `addr` parameter which was
meant to pass in an address of the reset vector location, where the CPU
should reset to.  This feature is no longer used anywhere in U-Boot as
all reset_cpu() implementations now ignore the passed value.  Generic
code has been added which always calls reset_cpu() with `0` which means
this feature can no longer be used easily anyway.

Over time, many implementations seem to have "misunderstood" the
existence of this parameter as a way to customize/parameterize the reset
(e.g.  COLD vs WARM resets).  As this is not properly supported, the
code will almost always not do what it is intended to (because all
call-sites just call reset_cpu() with 0).

To avoid confusion and to clean up the codebase from unused left-overs
of the past, remove the `addr` parameter entirely.  Code which intends
to support different kinds of resets should be rewritten as a sysreset
driver instead.

This transformation was done with the following coccinelle patch:

    @@
    expression argvalue;
    @@
    - reset_cpu(argvalue)
    + reset_cpu()

    @@
    identifier argname;
    type argtype;
    @@
    - reset_cpu(argtype argname)
    + reset_cpu(void)
    { ... }

Signed-off-by: Harald Seiler 
Reviewed-by: Simon Glass

common: Drop asm/global_data.h from common header

2021-02-02T20:33:42+00:00

Move this out of the common header and include it only where needed.  In
a number of cases this requires adding "struct udevice;" to avoid adding
another large header or in other cases replacing / adding missing header
files that had been pulled in, very indirectly.   Finally, we have a few
cases where we did not need to include  at all, so
remove that include.

Signed-off-by: Simon Glass 
Signed-off-by: Tom Rini

mx7ulp: clock: Align the PLL_USB frequency

2020-11-01T14:53:29+00:00

The command 'clocks' shows the following output:

=> clocks
PLL_A7_SPLL         528 MHz
PLL_A7_APLL         529 MHz
PLL_USB           0 MHz

Add some extra spaces so that the PLL_USB information gets aligned with
the previous reported frequencies.

Signed-off-by: Fabio Estevam

mx7ulp: clock: Remove unuseful information

2020-11-01T14:53:17+00:00

The command 'clocks' shows the following output:

=> clocks
PLL_A7_SPLL         528 MHz
PLL_A7_APLL         529 MHz
PLL_USB           0 MHz

....

[do_mx7_showclocks] addr = 0x9FFB61F1

The last line is not useful at all, so just remove it.

Signed-off-by: Fabio Estevam

common: Drop linux/bitops.h from common header

2020-05-19T01:19:23+00:00

Move this uncommon header out of the common header.

Signed-off-by: Simon Glass

common: Drop linux/delay.h from common header

2020-05-19T01:19:23+00:00

Move this uncommon header out of the common header.

Signed-off-by: Simon Glass

common: Drop log.h from common header

2020-05-19T01:19:18+00:00

Move this header out of the common header.

Signed-off-by: Simon Glass

command: Remove the cmd_tbl_t typedef

2020-05-18T22:36:55+00:00

We should not use typedefs in U-Boot. They cannot be used as forward
declarations which means that header files must include the full header to
access them.

Drop the typedef and rename the struct to remove the _s suffix which is
now not useful.

This requires quite a few header-file additions.

Signed-off-by: Simon Glass

arm: Don't include common.h in header files

2020-05-18T18:54:24+00:00

It is bad practice to include common.h in other header files since it can
bring in any number of superfluous definitions. It implies that some C
files don't include it and thus may be missing CONFIG options that are set
up by that file. The C files should include these themselves.

Update some header files in arch/arm to drop this.

Signed-off-by: Simon Glass