diff options
Diffstat (limited to 'isys/ethtool-copy.h')
-rw-r--r-- | isys/ethtool-copy.h | 360 |
1 files changed, 0 insertions, 360 deletions
diff --git a/isys/ethtool-copy.h b/isys/ethtool-copy.h deleted file mode 100644 index f588b728f..000000000 --- a/isys/ethtool-copy.h +++ /dev/null @@ -1,360 +0,0 @@ -/* - * ethtool.h: Defines for Linux ethtool. - * - * Copyright (C) 1998 David S. Miller (davem@redhat.com) - * Copyright 2001 Jeff Garzik <jgarzik@mandrakesoft.com> - * Portions Copyright 2001 Sun Microsystems (thockin@sun.com) - * Portions Copyright 2002 Intel (eli.kupermann@intel.com, - * christopher.leech@intel.com, - * scott.feldman@intel.com) - */ - -#ifndef _LINUX_ETHTOOL_H -#define _LINUX_ETHTOOL_H - -/* This should work for both 32 and 64 bit userland. */ -struct ethtool_cmd { - u32 cmd; - u32 supported; /* Features this interface supports */ - u32 advertising; /* Features this interface advertises */ - u16 speed; /* The forced speed, 10Mb, 100Mb, gigabit */ - u8 duplex; /* Duplex, half or full */ - u8 port; /* Which connector port */ - u8 phy_address; - u8 transceiver; /* Which tranceiver to use */ - u8 autoneg; /* Enable or disable autonegotiation */ - u32 maxtxpkt; /* Tx pkts before generating tx int */ - u32 maxrxpkt; /* Rx pkts before generating rx int */ - u32 reserved[4]; -}; - -#define ETHTOOL_BUSINFO_LEN 32 -/* these strings are set to whatever the driver author decides... */ -struct ethtool_drvinfo { - u32 cmd; - char driver[32]; /* driver short name, "tulip", "eepro100" */ - char version[32]; /* driver version string */ - char fw_version[32]; /* firmware version string, if applicable */ - char bus_info[ETHTOOL_BUSINFO_LEN]; /* Bus info for this IF. */ - /* For PCI devices, use pci_dev->slot_name. */ - char reserved1[32]; - char reserved2[16]; - u32 n_stats; /* number of u64's from ETHTOOL_GSTATS */ - u32 testinfo_len; - u32 eedump_len; /* Size of data from ETHTOOL_GEEPROM (bytes) */ - u32 regdump_len; /* Size of data from ETHTOOL_GREGS (bytes) */ -}; - -#define SOPASS_MAX 6 -/* wake-on-lan settings */ -struct ethtool_wolinfo { - u32 cmd; - u32 supported; - u32 wolopts; - u8 sopass[SOPASS_MAX]; /* SecureOn(tm) password */ -}; - -/* for passing single values */ -struct ethtool_value { - u32 cmd; - u32 data; -}; - -/* for passing big chunks of data */ -struct ethtool_regs { - u32 cmd; - u32 version; /* driver-specific, indicates different chips/revs */ - u32 len; /* bytes */ - u8 data[0]; -}; - -/* for passing EEPROM chunks */ -struct ethtool_eeprom { - u32 cmd; - u32 magic; - u32 offset; /* in bytes */ - u32 len; /* in bytes */ - u8 data[0]; -}; - -/* for configuring coalescing parameters of chip */ -struct ethtool_coalesce { - u32 cmd; /* ETHTOOL_{G,S}COALESCE */ - - /* How many usecs to delay an RX interrupt after - * a packet arrives. If 0, only rx_max_coalesced_frames - * is used. - */ - u32 rx_coalesce_usecs; - - /* How many packets to delay an RX interrupt after - * a packet arrives. If 0, only rx_coalesce_usecs is - * used. It is illegal to set both usecs and max frames - * to zero as this would cause RX interrupts to never be - * generated. - */ - u32 rx_max_coalesced_frames; - - /* Same as above two parameters, except that these values - * apply while an IRQ is being services by the host. Not - * all cards support this feature and the values are ignored - * in that case. - */ - u32 rx_coalesce_usecs_irq; - u32 rx_max_coalesced_frames_irq; - - /* How many usecs to delay a TX interrupt after - * a packet is sent. If 0, only tx_max_coalesced_frames - * is used. - */ - u32 tx_coalesce_usecs; - - /* How many packets to delay a TX interrupt after - * a packet is sent. If 0, only tx_coalesce_usecs is - * used. It is illegal to set both usecs and max frames - * to zero as this would cause TX interrupts to never be - * generated. - */ - u32 tx_max_coalesced_frames; - - /* Same as above two parameters, except that these values - * apply while an IRQ is being services by the host. Not - * all cards support this feature and the values are ignored - * in that case. - */ - u32 tx_coalesce_usecs_irq; - u32 tx_max_coalesced_frames_irq; - - /* How many usecs to delay in-memory statistics - * block updates. Some drivers do not have an in-memory - * statistic block, and in such cases this value is ignored. - * This value must not be zero. - */ - u32 stats_block_coalesce_usecs; - - /* Adaptive RX/TX coalescing is an algorithm implemented by - * some drivers to improve latency under low packet rates and - * improve throughput under high packet rates. Some drivers - * only implement one of RX or TX adaptive coalescing. Anything - * not implemented by the driver causes these values to be - * silently ignored. - */ - u32 use_adaptive_rx_coalesce; - u32 use_adaptive_tx_coalesce; - - /* When the packet rate (measured in packets per second) - * is below pkt_rate_low, the {rx,tx}_*_low parameters are - * used. - */ - u32 pkt_rate_low; - u32 rx_coalesce_usecs_low; - u32 rx_max_coalesced_frames_low; - u32 tx_coalesce_usecs_low; - u32 tx_max_coalesced_frames_low; - - /* When the packet rate is below pkt_rate_high but above - * pkt_rate_low (both measured in packets per second) the - * normal {rx,tx}_* coalescing parameters are used. - */ - - /* When the packet rate is (measured in packets per second) - * is above pkt_rate_high, the {rx,tx}_*_high parameters are - * used. - */ - u32 pkt_rate_high; - u32 rx_coalesce_usecs_high; - u32 rx_max_coalesced_frames_high; - u32 tx_coalesce_usecs_high; - u32 tx_max_coalesced_frames_high; - - /* How often to do adaptive coalescing packet rate sampling, - * measured in seconds. Must not be zero. - */ - u32 rate_sample_interval; -}; - -/* for configuring RX/TX ring parameters */ -struct ethtool_ringparam { - u32 cmd; /* ETHTOOL_{G,S}RINGPARAM */ - - /* Read only attributes. These indicate the maximum number - * of pending RX/TX ring entries the driver will allow the - * user to set. - */ - u32 rx_max_pending; - u32 rx_mini_max_pending; - u32 rx_jumbo_max_pending; - u32 tx_max_pending; - - /* Values changeable by the user. The valid values are - * in the range 1 to the "*_max_pending" counterpart above. - */ - u32 rx_pending; - u32 rx_mini_pending; - u32 rx_jumbo_pending; - u32 tx_pending; -}; - -/* for configuring link flow control parameters */ -struct ethtool_pauseparam { - u32 cmd; /* ETHTOOL_{G,S}PAUSEPARAM */ - - /* If the link is being auto-negotiated (via ethtool_cmd.autoneg - * being true) the user may set 'autonet' here non-zero to have the - * pause parameters be auto-negotiated too. In such a case, the - * {rx,tx}_pause values below determine what capabilities are - * advertised. - * - * If 'autoneg' is zero or the link is not being auto-negotiated, - * then {rx,tx}_pause force the driver to use/not-use pause - * flow control. - */ - u32 autoneg; - u32 rx_pause; - u32 tx_pause; -}; - -#define ETH_GSTRING_LEN 32 -enum ethtool_stringset { - ETH_SS_TEST = 0, - ETH_SS_STATS, -}; - -/* for passing string sets for data tagging */ -struct ethtool_gstrings { - u32 cmd; /* ETHTOOL_GSTRINGS */ - u32 string_set; /* string set id e.c. ETH_SS_TEST, etc*/ - u32 len; /* number of strings in the string set */ - u8 data[0]; -}; - -enum ethtool_test_flags { - ETH_TEST_FL_OFFLINE = (1 << 0), /* online / offline */ - ETH_TEST_FL_FAILED = (1 << 1), /* test passed / failed */ -}; - -/* for requesting NIC test and getting results*/ -struct ethtool_test { - u32 cmd; /* ETHTOOL_TEST */ - u32 flags; /* ETH_TEST_FL_xxx */ - u32 reserved; - u32 len; /* result length, in number of u64 elements */ - u64 data[0]; -}; - -/* for dumping NIC-specific statistics */ -struct ethtool_stats { - u32 cmd; /* ETHTOOL_GSTATS */ - u32 n_stats; /* number of u64's being returned */ - u64 data[0]; -}; - -/* CMDs currently supported */ -#define ETHTOOL_GSET 0x00000001 /* Get settings. */ -#define ETHTOOL_SSET 0x00000002 /* Set settings, privileged. */ -#define ETHTOOL_GDRVINFO 0x00000003 /* Get driver info. */ -#define ETHTOOL_GREGS 0x00000004 /* Get NIC registers, privileged. */ -#define ETHTOOL_GWOL 0x00000005 /* Get wake-on-lan options. */ -#define ETHTOOL_SWOL 0x00000006 /* Set wake-on-lan options, priv. */ -#define ETHTOOL_GMSGLVL 0x00000007 /* Get driver message level */ -#define ETHTOOL_SMSGLVL 0x00000008 /* Set driver msg level, priv. */ -#define ETHTOOL_NWAY_RST 0x00000009 /* Restart autonegotiation, priv. */ -#define ETHTOOL_GLINK 0x0000000a /* Get link status (ethtool_value) */ -#define ETHTOOL_GEEPROM 0x0000000b /* Get EEPROM data */ -#define ETHTOOL_SEEPROM 0x0000000c /* Set EEPROM data, priv. */ -#define ETHTOOL_GCOALESCE 0x0000000e /* Get coalesce config */ -#define ETHTOOL_SCOALESCE 0x0000000f /* Set coalesce config, priv. */ -#define ETHTOOL_GRINGPARAM 0x00000010 /* Get ring parameters */ -#define ETHTOOL_SRINGPARAM 0x00000011 /* Set ring parameters, priv. */ -#define ETHTOOL_GPAUSEPARAM 0x00000012 /* Get pause parameters */ -#define ETHTOOL_SPAUSEPARAM 0x00000013 /* Set pause parameters, priv. */ -#define ETHTOOL_GRXCSUM 0x00000014 /* Get RX hw csum enable (ethtool_value) */ -#define ETHTOOL_SRXCSUM 0x00000015 /* Set RX hw csum enable (ethtool_value) */ -#define ETHTOOL_GTXCSUM 0x00000016 /* Get TX hw csum enable (ethtool_value) */ -#define ETHTOOL_STXCSUM 0x00000017 /* Set TX hw csum enable (ethtool_value) */ -#define ETHTOOL_GSG 0x00000018 /* Get scatter-gather enable - * (ethtool_value) */ -#define ETHTOOL_SSG 0x00000019 /* Set scatter-gather enable - * (ethtool_value), priv. */ -#define ETHTOOL_TEST 0x0000001a /* execute NIC self-test, priv. */ -#define ETHTOOL_GSTRINGS 0x0000001b /* get specified string set */ -#define ETHTOOL_PHYS_ID 0x0000001c /* identify the NIC */ -#define ETHTOOL_GSTATS 0x0000001d /* get NIC-specific statistics */ - -/* compatibility with older code */ -#define SPARC_ETH_GSET ETHTOOL_GSET -#define SPARC_ETH_SSET ETHTOOL_SSET - -/* Indicates what features are supported by the interface. */ -#define SUPPORTED_10baseT_Half (1 << 0) -#define SUPPORTED_10baseT_Full (1 << 1) -#define SUPPORTED_100baseT_Half (1 << 2) -#define SUPPORTED_100baseT_Full (1 << 3) -#define SUPPORTED_1000baseT_Half (1 << 4) -#define SUPPORTED_1000baseT_Full (1 << 5) -#define SUPPORTED_Autoneg (1 << 6) -#define SUPPORTED_TP (1 << 7) -#define SUPPORTED_AUI (1 << 8) -#define SUPPORTED_MII (1 << 9) -#define SUPPORTED_FIBRE (1 << 10) -#define SUPPORTED_BNC (1 << 11) - -/* Indicates what features are advertised by the interface. */ -#define ADVERTISED_10baseT_Half (1 << 0) -#define ADVERTISED_10baseT_Full (1 << 1) -#define ADVERTISED_100baseT_Half (1 << 2) -#define ADVERTISED_100baseT_Full (1 << 3) -#define ADVERTISED_1000baseT_Half (1 << 4) -#define ADVERTISED_1000baseT_Full (1 << 5) -#define ADVERTISED_Autoneg (1 << 6) -#define ADVERTISED_TP (1 << 7) -#define ADVERTISED_AUI (1 << 8) -#define ADVERTISED_MII (1 << 9) -#define ADVERTISED_FIBRE (1 << 10) -#define ADVERTISED_BNC (1 << 11) - -/* The following are all involved in forcing a particular link - * mode for the device for setting things. When getting the - * devices settings, these indicate the current mode and whether - * it was foced up into this mode or autonegotiated. - */ - -/* The forced speed, 10Mb, 100Mb, gigabit. */ -#define SPEED_10 10 -#define SPEED_100 100 -#define SPEED_1000 1000 - -/* Duplex, half or full. */ -#define DUPLEX_HALF 0x00 -#define DUPLEX_FULL 0x01 - -/* Which connector port. */ -#define PORT_TP 0x00 -#define PORT_AUI 0x01 -#define PORT_MII 0x02 -#define PORT_FIBRE 0x03 -#define PORT_BNC 0x04 - -/* Which tranceiver to use. */ -#define XCVR_INTERNAL 0x00 -#define XCVR_EXTERNAL 0x01 -#define XCVR_DUMMY1 0x02 -#define XCVR_DUMMY2 0x03 -#define XCVR_DUMMY3 0x04 - -/* Enable or disable autonegotiation. If this is set to enable, - * the forced link modes above are completely ignored. - */ -#define AUTONEG_DISABLE 0x00 -#define AUTONEG_ENABLE 0x01 - -/* Wake-On-Lan options. */ -#define WAKE_PHY (1 << 0) -#define WAKE_UCAST (1 << 1) -#define WAKE_MCAST (1 << 2) -#define WAKE_BCAST (1 << 3) -#define WAKE_ARP (1 << 4) -#define WAKE_MAGIC (1 << 5) -#define WAKE_MAGICSECURE (1 << 6) /* only meaningful if WAKE_MAGIC */ - -#endif /* _LINUX_ETHTOOL_H */ |