1 files changed, 80 insertions, 34 deletions

diff --git a/arch/arm/mach-omap2/serial.c b/arch/arm/mach-omap2/serial.c
index 619f864c40b..c1b93c752d7 100644
--- a/arch/arm/mach-omap2/serial.c
+++ b/arch/arm/mach-omap2/serial.c
@@ -57,6 +57,7 @@ struct omap_uart_state {
 
 	struct list_head node;
 	struct omap_hwmod *oh;
+	struct omap_device_pad default_omap_uart_pads[2];
 };
 
 static LIST_HEAD(uart_list);
@@ -126,14 +127,73 @@ static void omap_uart_set_smartidle(struct platform_device *pdev) {}
 #endif /* CONFIG_PM */
 
 #ifdef CONFIG_OMAP_MUX
-static void omap_serial_fill_default_pads(struct omap_board_data *bdata)
+
+#define OMAP_UART_DEFAULT_PAD_NAME_LEN	28
+static char rx_pad_name[OMAP_UART_DEFAULT_PAD_NAME_LEN],
+		tx_pad_name[OMAP_UART_DEFAULT_PAD_NAME_LEN] __initdata;
+
+static void  __init
+omap_serial_fill_uart_tx_rx_pads(struct omap_board_data *bdata,
+				struct omap_uart_state *uart)
+{
+	uart->default_omap_uart_pads[0].name = rx_pad_name;
+	uart->default_omap_uart_pads[0].flags = OMAP_DEVICE_PAD_REMUX |
+							OMAP_DEVICE_PAD_WAKEUP;
+	uart->default_omap_uart_pads[0].enable = OMAP_PIN_INPUT |
+							OMAP_MUX_MODE0;
+	uart->default_omap_uart_pads[0].idle = OMAP_PIN_INPUT | OMAP_MUX_MODE0;
+	uart->default_omap_uart_pads[1].name = tx_pad_name;
+	uart->default_omap_uart_pads[1].enable = OMAP_PIN_OUTPUT |
+							OMAP_MUX_MODE0;
+	bdata->pads = uart->default_omap_uart_pads;
+	bdata->pads_cnt = ARRAY_SIZE(uart->default_omap_uart_pads);
+}
+
+static void  __init omap_serial_check_wakeup(struct omap_board_data *bdata,
+						struct omap_uart_state *uart)
 {
+	struct omap_mux_partition *tx_partition = NULL, *rx_partition = NULL;
+	struct omap_mux *rx_mux = NULL, *tx_mux = NULL;
+	char *rx_fmt, *tx_fmt;
+	int uart_nr = bdata->id + 1;
+
+	if (bdata->id != 2) {
+		rx_fmt = "uart%d_rx.uart%d_rx";
+		tx_fmt = "uart%d_tx.uart%d_tx";
+	} else {
+		rx_fmt = "uart%d_rx_irrx.uart%d_rx_irrx";
+		tx_fmt = "uart%d_tx_irtx.uart%d_tx_irtx";
+	}
+
+	snprintf(rx_pad_name, OMAP_UART_DEFAULT_PAD_NAME_LEN, rx_fmt,
+			uart_nr, uart_nr);
+	snprintf(tx_pad_name, OMAP_UART_DEFAULT_PAD_NAME_LEN, tx_fmt,
+			uart_nr, uart_nr);
+
+	if (omap_mux_get_by_name(rx_pad_name, &rx_partition, &rx_mux) >= 0 &&
+			omap_mux_get_by_name
+				(tx_pad_name, &tx_partition, &tx_mux) >= 0) {
+		u16 tx_mode, rx_mode;
+
+		tx_mode = omap_mux_read(tx_partition, tx_mux->reg_offset);
+		rx_mode = omap_mux_read(rx_partition, rx_mux->reg_offset);
+
+		/*
+		 * Check if uart is used in default tx/rx mode i.e. in mux mode0
+		 * if yes then configure rx pin for wake up capability
+		 */
+		if (OMAP_MODE_UART(rx_mode) && OMAP_MODE_UART(tx_mode))
+			omap_serial_fill_uart_tx_rx_pads(bdata, uart);
+	}
 }
 #else
-static void omap_serial_fill_default_pads(struct omap_board_data *bdata) {}
+static void __init omap_serial_check_wakeup(struct omap_board_data *bdata,
+		struct omap_uart_state *uart)
+{
+}
 #endif
 
-char *cmdline_find_option(char *str)
+static char *cmdline_find_option(char *str)
 {
 	extern char *saved_command_line;
 
@@ -245,14 +305,6 @@ void __init omap_serial_init_port(struct omap_board_data *bdata,
 	omap_up.dma_rx_poll_rate = info->dma_rx_poll_rate;
 	omap_up.autosuspend_timeout = info->autosuspend_timeout;
 
-	/* Enable the MDR1 Errata i202 for OMAP2430/3xxx/44xx */
-	if (!cpu_is_omap2420() && !cpu_is_ti816x())
-		omap_up.errata |= UART_ERRATA_i202_MDR1_ACCESS;
-
-	/* Enable DMA Mode Force Idle Errata i291 for omap34xx/3630 */
-	if (cpu_is_omap34xx() || cpu_is_omap3630())
-		omap_up.errata |= UART_ERRATA_i291_DMA_FORCEIDLE;
-
 	pdata = &omap_up;
 	pdata_size = sizeof(struct omap_uart_port_info);
 
@@ -279,32 +331,29 @@ void __init omap_serial_init_port(struct omap_board_data *bdata,
 /**
  * omap_serial_board_init() - initialize all supported serial ports
  * @info: platform specific data pointer
- * @port_id: uart port number to be initialised
  *
- * Initializes individual UARTs as serial ports. Platforms
+ * Initializes all available UARTs as serial ports. Platforms
  * can call this function when they want to have default behaviour
- * for serial ports (e.g initialize individual serial ports based on port id).
+ * for serial ports (e.g initialize them all as serial ports).
  */
-void __init omap_serial_board_init(struct omap_uart_port_info *info, u8 port_id)
+void __init omap_serial_board_init(struct omap_uart_port_info *info)
 {
 	struct omap_uart_state *uart;
 	struct omap_board_data bdata;
 
-	list_for_each_entry(uart, &uart_list, node)
-		if (uart->num == port_id) {
-			bdata.id = uart->num;
-			bdata.flags = 0;
-			bdata.pads = NULL;
-			bdata.pads_cnt = 0;
-
-			if (!cpu_is_omap24xx())
-				omap_serial_fill_default_pads(&bdata);
-
-			if (!info)
-				omap_serial_init_port(&bdata, NULL);
-			else
-				omap_serial_init_port(&bdata, info);
-		}
+	list_for_each_entry(uart, &uart_list, node) {
+		bdata.id = uart->num;
+		bdata.flags = 0;
+		bdata.pads = NULL;
+		bdata.pads_cnt = 0;
+
+		omap_serial_check_wakeup(&bdata, uart);
+
+		if (!info)
+			omap_serial_init_port(&bdata, NULL);
+		else
+			omap_serial_init_port(&bdata, &info[uart->num]);
+	}
 }
 
 /**
@@ -316,8 +365,5 @@ void __init omap_serial_board_init(struct omap_uart_port_info *info, u8 port_id)
  */
 void __init omap_serial_init(void)
 {
-	struct omap_uart_state *uart;
-
-	list_for_each_entry(uart, &uart_list, node)
-		omap_serial_board_init(NULL, uart->num);
+	omap_serial_board_init(NULL);
 }