path: root/Documentation/networking/smctr.txt
diff options
Diffstat (limited to 'Documentation/networking/smctr.txt')
1 files changed, 0 insertions, 66 deletions
diff --git a/Documentation/networking/smctr.txt b/Documentation/networking/smctr.txt
deleted file mode 100644
index 9af25b810c1..00000000000
--- a/Documentation/networking/smctr.txt
+++ /dev/null
@@ -1,66 +0,0 @@
-Text File for the SMC TokenCard TokenRing Linux driver (smctr.c).
- By Jay Schulist <>
-The Linux SMC Token Ring driver works with the SMC TokenCard Elite (8115T)
-ISA and SMC TokenCard Elite/A (8115T/A) MCA adapters.
-Latest information on this driver can be obtained on the Linux-SNA WWW site.
-Please point your browser to:
-This driver is rather simple to use. Select Y to Token Ring adapter support
-in the kernel configuration. A choice for SMC Token Ring adapters will
-appear. This drives supports all SMC ISA/MCA adapters. Choose this
-option. I personally recommend compiling the driver as a module (M), but if you
-you would like to compile it statically answer Y instead.
-This driver supports multiple adapters without the need to load multiple copies
-of the driver. You should be able to load up to 7 adapters without any kernel
-modifications, if you are in need of more please contact the maintainer of this
-Load the driver either by lilo/loadlin or as a module. When a module using the
-following command will suffice for most:
-# modprobe smctr
-smctr.c: v1.00 12/6/99 by
-tr0: SMC TokenCard 8115T at Io 0x300, Irq 10, Rom 0xd8000, Ram 0xcc000.
-Now just setup the device via ifconfig and set and routes you may have. After
-this you are ready to start sending some tokens.
-1). For anyone wondering where to pick up the SMC adapters please browse
- to
-2). If you are the first/only Token Ring Client on a Token Ring LAN, please
- specify the ringspeed with the ringspeed=[4/16] module option. If no
- ringspeed is specified the driver will attempt to autodetect the ring
- speed and/or if the adapter is the first/only station on the ring take
- the appropriate actions.
- NOTE: Default ring speed is 16MB UTP.
-3). PnP support for this adapter sucks. I recommend hard setting the
- IO/MEM/IRQ by the jumpers on the adapter. If this is not possible
- load the module with the following io=[ioaddr] mem=[mem_addr]
- irq=[irq_num].
- The following IRQ, IO, and MEM settings are supported.
- IO ports:
- 0x200, 0x220, 0x240, 0x260, 0x280, 0x2A0, 0x2C0, 0x2E0, 0x300,
- 0x320, 0x340, 0x360, 0x380.
- IRQs:
- 2, 3, 4, 5, 7, 8, 9, 10, 11, 12, 13, 14, 15
- Memory addresses:
- 0xA0000, 0xA4000, 0xA8000, 0xAC000, 0xB0000, 0xB4000,
- 0xB8000, 0xBC000, 0xC0000, 0xC4000, 0xC8000, 0xCC000,
- 0xD0000, 0xD4000, 0xD8000, 0xDC000, 0xE0000, 0xE4000,
- 0xE8000, 0xEC000, 0xF0000, 0xF4000, 0xF8000, 0xFC000
-This driver is under the GNU General Public License. Its Firmware image is
-included as an initialized C-array and is licensed by SMC to the Linux
-users of this driver. However no warranty about its fitness is expressed or
-implied by SMC.