summaryrefslogtreecommitdiffstats
path: root/Documentation/hwmon/smsc47b397
diff options
context:
space:
mode:
Diffstat (limited to 'Documentation/hwmon/smsc47b397')
-rw-r--r--Documentation/hwmon/smsc47b397163
1 files changed, 0 insertions, 163 deletions
diff --git a/Documentation/hwmon/smsc47b397 b/Documentation/hwmon/smsc47b397
deleted file mode 100644
index 3a43b69..0000000
--- a/Documentation/hwmon/smsc47b397
+++ /dev/null
@@ -1,163 +0,0 @@
-Kernel driver smsc47b397
-========================
-
-Supported chips:
- * SMSC LPC47B397-NC
- * SMSC SCH5307-NS
- * SMSC SCH5317
- Prefix: 'smsc47b397'
- Addresses scanned: none, address read from Super I/O config space
- Datasheet: In this file
-
-Authors: Mark M. Hoffman <mhoffman@lightlink.com>
- Utilitek Systems, Inc.
-
-November 23, 2004
-
-The following specification describes the SMSC LPC47B397-NC[1] sensor chip
-(for which there is no public datasheet available). This document was
-provided by Craig Kelly (In-Store Broadcast Network) and edited/corrected
-by Mark M. Hoffman <mhoffman@lightlink.com>.
-
-[1] And SMSC SCH5307-NS and SCH5317, which have different device IDs but are
-otherwise compatible.
-
-* * * * *
-
-Methods for detecting the HP SIO and reading the thermal data on a dc7100.
-
-The thermal information on the dc7100 is contained in the SIO Hardware Monitor
-(HWM). The information is accessed through an index/data pair. The index/data
-pair is located at the HWM Base Address + 0 and the HWM Base Address + 1. The
-HWM Base address can be obtained from Logical Device 8, registers 0x60 (MSB)
-and 0x61 (LSB). Currently we are using 0x480 for the HWM Base Address and
-0x480 and 0x481 for the index/data pair.
-
-Reading temperature information.
-The temperature information is located in the following registers:
-Temp1 0x25 (Currently, this reflects the CPU temp on all systems).
-Temp2 0x26
-Temp3 0x27
-Temp4 0x80
-
-Programming Example
-The following is an example of how to read the HWM temperature registers:
-MOV DX,480H
-MOV AX,25H
-OUT DX,AL
-MOV DX,481H
-IN AL,DX
-
-AL contains the data in hex, the temperature in Celsius is the decimal
-equivalent.
-
-Ex: If AL contains 0x2A, the temperature is 42 degrees C.
-
-Reading tach information.
-The fan speed information is located in the following registers:
- LSB MSB
-Tach1 0x28 0x29 (Currently, this reflects the CPU
- fan speed on all systems).
-Tach2 0x2A 0x2B
-Tach3 0x2C 0x2D
-Tach4 0x2E 0x2F
-
-Important!!!
-Reading the tach LSB locks the tach MSB.
-The LSB Must be read first.
-
-How to convert the tach reading to RPM.
-The tach reading (TCount) is given by: (Tach MSB * 256) + (Tach LSB)
-The SIO counts the number of 90kHz (11.111us) pulses per revolution.
-RPM = 60/(TCount * 11.111us)
-
-Example:
-Reg 0x28 = 0x9B
-Reg 0x29 = 0x08
-
-TCount = 0x89B = 2203
-
-RPM = 60 / (2203 * 11.11111 E-6) = 2451 RPM
-
-Obtaining the SIO version.
-
-CONFIGURATION SEQUENCE
-To program the configuration registers, the following sequence must be followed:
-1. Enter Configuration Mode
-2. Configure the Configuration Registers
-3. Exit Configuration Mode.
-
-Enter Configuration Mode
-To place the chip into the Configuration State The config key (0x55) is written
-to the CONFIG PORT (0x2E).
-
-Configuration Mode
-In configuration mode, the INDEX PORT is located at the CONFIG PORT address and
-the DATA PORT is at INDEX PORT address + 1.
-
-The desired configuration registers are accessed in two steps:
-a. Write the index of the Logical Device Number Configuration Register
- (i.e., 0x07) to the INDEX PORT and then write the number of the
- desired logical device to the DATA PORT.
-
-b. Write the address of the desired configuration register within the
- logical device to the INDEX PORT and then write or read the config-
- uration register through the DATA PORT.
-
-Note: If accessing the Global Configuration Registers, step (a) is not required.
-
-Exit Configuration Mode
-To exit the Configuration State the write 0xAA to the CONFIG PORT (0x2E).
-The chip returns to the RUN State. (This is important).
-
-Programming Example
-The following is an example of how to read the SIO Device ID located at 0x20
-
-; ENTER CONFIGURATION MODE
-MOV DX,02EH
-MOV AX,055H
-OUT DX,AL
-; GLOBAL CONFIGURATION REGISTER
-MOV DX,02EH
-MOV AL,20H
-OUT DX,AL
-; READ THE DATA
-MOV DX,02FH
-IN AL,DX
-; EXIT CONFIGURATION MODE
-MOV DX,02EH
-MOV AX,0AAH
-OUT DX,AL
-
-The registers of interest for identifying the SIO on the dc7100 are Device ID
-(0x20) and Device Rev (0x21).
-
-The Device ID will read 0x6F (0x81 for SCH5307-NS, and 0x85 for SCH5317)
-The Device Rev currently reads 0x01
-
-Obtaining the HWM Base Address.
-The following is an example of how to read the HWM Base Address located in
-Logical Device 8.
-
-; ENTER CONFIGURATION MODE
-MOV DX,02EH
-MOV AX,055H
-OUT DX,AL
-; CONFIGURE REGISTER CRE0,
-; LOGICAL DEVICE 8
-MOV DX,02EH
-MOV AL,07H
-OUT DX,AL ;Point to LD# Config Reg
-MOV DX,02FH
-MOV AL, 08H
-OUT DX,AL;Point to Logical Device 8
-;
-MOV DX,02EH
-MOV AL,60H
-OUT DX,AL ; Point to HWM Base Addr MSB
-MOV DX,02FH
-IN AL,DX ; Get MSB of HWM Base Addr
-; EXIT CONFIGURATION MODE
-MOV DX,02EH
-MOV AX,0AAH
-OUT DX,AL