summaryrefslogtreecommitdiffstats
path: root/Documentation/devicetree/bindings/arm
diff options
context:
space:
mode:
Diffstat (limited to 'Documentation/devicetree/bindings/arm')
-rw-r--r--Documentation/devicetree/bindings/arm/atmel-aic.txt38
-rw-r--r--Documentation/devicetree/bindings/arm/atmel-at91.txt92
-rw-r--r--Documentation/devicetree/bindings/arm/atmel-pmc.txt11
-rw-r--r--Documentation/devicetree/bindings/arm/exynos/power_domain.txt21
-rw-r--r--Documentation/devicetree/bindings/arm/fsl.txt22
-rw-r--r--Documentation/devicetree/bindings/arm/mrvl.txt6
-rw-r--r--Documentation/devicetree/bindings/arm/omap/intc.txt27
-rw-r--r--Documentation/devicetree/bindings/arm/omap/omap.txt8
-rw-r--r--Documentation/devicetree/bindings/arm/sirf.txt2
-rw-r--r--Documentation/devicetree/bindings/arm/spear.txt8
-rw-r--r--Documentation/devicetree/bindings/arm/tegra/emc.txt100
-rw-r--r--Documentation/devicetree/bindings/arm/tegra/nvidia,tegra20-pmc.txt19
-rw-r--r--Documentation/devicetree/bindings/arm/twd.txt48
-rw-r--r--Documentation/devicetree/bindings/arm/vexpress.txt146
14 files changed, 546 insertions, 2 deletions
diff --git a/Documentation/devicetree/bindings/arm/atmel-aic.txt b/Documentation/devicetree/bindings/arm/atmel-aic.txt
new file mode 100644
index 00000000000..aabca4f8340
--- /dev/null
+++ b/Documentation/devicetree/bindings/arm/atmel-aic.txt
@@ -0,0 +1,38 @@
+* Advanced Interrupt Controller (AIC)
+
+Required properties:
+- compatible: Should be "atmel,<chip>-aic"
+- interrupt-controller: Identifies the node as an interrupt controller.
+- interrupt-parent: For single AIC system, it is an empty property.
+- #interrupt-cells: The number of cells to define the interrupts. It sould be 2.
+ The first cell is the IRQ number (aka "Peripheral IDentifier" on datasheet).
+ The second cell is used to specify flags:
+ bits[3:0] trigger type and level flags:
+ 1 = low-to-high edge triggered.
+ 2 = high-to-low edge triggered.
+ 4 = active high level-sensitive.
+ 8 = active low level-sensitive.
+ Valid combinations are 1, 2, 3, 4, 8.
+ Default flag for internal sources should be set to 4 (active high).
+- reg: Should contain AIC registers location and length
+
+Examples:
+ /*
+ * AIC
+ */
+ aic: interrupt-controller@fffff000 {
+ compatible = "atmel,at91rm9200-aic";
+ interrupt-controller;
+ interrupt-parent;
+ #interrupt-cells = <2>;
+ reg = <0xfffff000 0x200>;
+ };
+
+ /*
+ * An interrupt generating device that is wired to an AIC.
+ */
+ dma: dma-controller@ffffec00 {
+ compatible = "atmel,at91sam9g45-dma";
+ reg = <0xffffec00 0x200>;
+ interrupts = <21 4>;
+ };
diff --git a/Documentation/devicetree/bindings/arm/atmel-at91.txt b/Documentation/devicetree/bindings/arm/atmel-at91.txt
new file mode 100644
index 00000000000..ecc81e36871
--- /dev/null
+++ b/Documentation/devicetree/bindings/arm/atmel-at91.txt
@@ -0,0 +1,92 @@
+Atmel AT91 device tree bindings.
+================================
+
+PIT Timer required properties:
+- compatible: Should be "atmel,at91sam9260-pit"
+- reg: Should contain registers location and length
+- interrupts: Should contain interrupt for the PIT which is the IRQ line
+ shared across all System Controller members.
+
+TC/TCLIB Timer required properties:
+- compatible: Should be "atmel,<chip>-pit".
+ <chip> can be "at91rm9200" or "at91sam9x5"
+- reg: Should contain registers location and length
+- interrupts: Should contain all interrupts for the TC block
+ Note that you can specify several interrupt cells if the TC
+ block has one interrupt per channel.
+
+Examples:
+
+One interrupt per TC block:
+ tcb0: timer@fff7c000 {
+ compatible = "atmel,at91rm9200-tcb";
+ reg = <0xfff7c000 0x100>;
+ interrupts = <18 4>;
+ };
+
+One interrupt per TC channel in a TC block:
+ tcb1: timer@fffdc000 {
+ compatible = "atmel,at91rm9200-tcb";
+ reg = <0xfffdc000 0x100>;
+ interrupts = <26 4 27 4 28 4>;
+ };
+
+RSTC Reset Controller required properties:
+- compatible: Should be "atmel,<chip>-rstc".
+ <chip> can be "at91sam9260" or "at91sam9g45"
+- reg: Should contain registers location and length
+
+Example:
+
+ rstc@fffffd00 {
+ compatible = "atmel,at91sam9260-rstc";
+ reg = <0xfffffd00 0x10>;
+ };
+
+RAMC SDRAM/DDR Controller required properties:
+- compatible: Should be "atmel,at91sam9260-sdramc",
+ "atmel,at91sam9g45-ddramc",
+- reg: Should contain registers location and length
+ For at91sam9263 and at91sam9g45 you must specify 2 entries.
+
+Examples:
+
+ ramc0: ramc@ffffe800 {
+ compatible = "atmel,at91sam9g45-ddramc";
+ reg = <0xffffe800 0x200>;
+ };
+
+ ramc0: ramc@ffffe400 {
+ compatible = "atmel,at91sam9g45-ddramc";
+ reg = <0xffffe400 0x200
+ 0xffffe600 0x200>;
+ };
+
+SHDWC Shutdown Controller
+
+required properties:
+- compatible: Should be "atmel,<chip>-shdwc".
+ <chip> can be "at91sam9260", "at91sam9rl" or "at91sam9x5".
+- reg: Should contain registers location and length
+
+optional properties:
+- atmel,wakeup-mode: String, operation mode of the wakeup mode.
+ Supported values are: "none", "high", "low", "any".
+- atmel,wakeup-counter: Counter on Wake-up 0 (between 0x0 and 0xf).
+
+optional at91sam9260 properties:
+- atmel,wakeup-rtt-timer: boolean to enable Real-time Timer Wake-up.
+
+optional at91sam9rl properties:
+- atmel,wakeup-rtc-timer: boolean to enable Real-time Clock Wake-up.
+- atmel,wakeup-rtt-timer: boolean to enable Real-time Timer Wake-up.
+
+optional at91sam9x5 properties:
+- atmel,wakeup-rtc-timer: boolean to enable Real-time Clock Wake-up.
+
+Example:
+
+ rstc@fffffd00 {
+ compatible = "atmel,at91sam9260-rstc";
+ reg = <0xfffffd00 0x10>;
+ };
diff --git a/Documentation/devicetree/bindings/arm/atmel-pmc.txt b/Documentation/devicetree/bindings/arm/atmel-pmc.txt
new file mode 100644
index 00000000000..389bed5056e
--- /dev/null
+++ b/Documentation/devicetree/bindings/arm/atmel-pmc.txt
@@ -0,0 +1,11 @@
+* Power Management Controller (PMC)
+
+Required properties:
+- compatible: Should be "atmel,at91rm9200-pmc"
+- reg: Should contain PMC registers location and length
+
+Examples:
+ pmc: pmc@fffffc00 {
+ compatible = "atmel,at91rm9200-pmc";
+ reg = <0xfffffc00 0x100>;
+ };
diff --git a/Documentation/devicetree/bindings/arm/exynos/power_domain.txt b/Documentation/devicetree/bindings/arm/exynos/power_domain.txt
new file mode 100644
index 00000000000..6528e215c5f
--- /dev/null
+++ b/Documentation/devicetree/bindings/arm/exynos/power_domain.txt
@@ -0,0 +1,21 @@
+* Samsung Exynos Power Domains
+
+Exynos processors include support for multiple power domains which are used
+to gate power to one or more peripherals on the processor.
+
+Required Properties:
+- compatiable: should be one of the following.
+ * samsung,exynos4210-pd - for exynos4210 type power domain.
+- reg: physical base address of the controller and length of memory mapped
+ region.
+
+Optional Properties:
+- samsung,exynos4210-pd-off: Specifies that the power domain is in turned-off
+ state during boot and remains to be turned-off until explicitly turned-on.
+
+Example:
+
+ lcd0: power-domain-lcd0 {
+ compatible = "samsung,exynos4210-pd";
+ reg = <0x10023C00 0x10>;
+ };
diff --git a/Documentation/devicetree/bindings/arm/fsl.txt b/Documentation/devicetree/bindings/arm/fsl.txt
index 54bdddadf1c..bfbc771a65f 100644
--- a/Documentation/devicetree/bindings/arm/fsl.txt
+++ b/Documentation/devicetree/bindings/arm/fsl.txt
@@ -28,3 +28,25 @@ Required root node properties:
i.MX6 Quad SABRE Lite Board
Required root node properties:
- compatible = "fsl,imx6q-sabrelite", "fsl,imx6q";
+
+Generic i.MX boards
+-------------------
+
+No iomux setup is done for these boards, so this must have been configured
+by the bootloader for boards to work with the generic bindings.
+
+i.MX27 generic board
+Required root node properties:
+ - compatible = "fsl,imx27";
+
+i.MX51 generic board
+Required root node properties:
+ - compatible = "fsl,imx51";
+
+i.MX53 generic board
+Required root node properties:
+ - compatible = "fsl,imx53";
+
+i.MX6q generic board
+Required root node properties:
+ - compatible = "fsl,imx6q";
diff --git a/Documentation/devicetree/bindings/arm/mrvl.txt b/Documentation/devicetree/bindings/arm/mrvl.txt
new file mode 100644
index 00000000000..d8de933e9d8
--- /dev/null
+++ b/Documentation/devicetree/bindings/arm/mrvl.txt
@@ -0,0 +1,6 @@
+Marvell Platforms Device Tree Bindings
+----------------------------------------------------
+
+PXA168 Aspenite Board
+Required root node properties:
+ - compatible = "mrvl,pxa168-aspenite", "mrvl,pxa168";
diff --git a/Documentation/devicetree/bindings/arm/omap/intc.txt b/Documentation/devicetree/bindings/arm/omap/intc.txt
new file mode 100644
index 00000000000..f2583e6ec06
--- /dev/null
+++ b/Documentation/devicetree/bindings/arm/omap/intc.txt
@@ -0,0 +1,27 @@
+* OMAP Interrupt Controller
+
+OMAP2/3 are using a TI interrupt controller that can support several
+configurable number of interrupts.
+
+Main node required properties:
+
+- compatible : should be:
+ "ti,omap2-intc"
+- interrupt-controller : Identifies the node as an interrupt controller
+- #interrupt-cells : Specifies the number of cells needed to encode an
+ interrupt source. The type shall be a <u32> and the value shall be 1.
+
+ The cell contains the interrupt number in the range [0-128].
+- ti,intc-size: Number of interrupts handled by the interrupt controller.
+- reg: physical base address and size of the intc registers map.
+
+Example:
+
+ intc: interrupt-controller@1 {
+ compatible = "ti,omap2-intc";
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ ti,intc-size = <96>;
+ reg = <0x48200000 0x1000>;
+ };
+
diff --git a/Documentation/devicetree/bindings/arm/omap/omap.txt b/Documentation/devicetree/bindings/arm/omap/omap.txt
index dbdab40ed3a..e78e8bccac3 100644
--- a/Documentation/devicetree/bindings/arm/omap/omap.txt
+++ b/Documentation/devicetree/bindings/arm/omap/omap.txt
@@ -5,7 +5,7 @@ IPs present in the SoC.
On top of that an omap_device is created to extend the platform_device
capabilities and to allow binding with one or several hwmods.
The hwmods will contain all the information to build the device:
-adresse range, irq lines, dma lines, interconnect, PRCM register,
+address range, irq lines, dma lines, interconnect, PRCM register,
clock domain, input clocks.
For the moment just point to the existing hwmod, the next step will be
to move data from hwmod to device-tree representation.
@@ -41,3 +41,9 @@ Boards:
- OMAP4 PandaBoard : Low cost community board
compatible = "ti,omap4-panda", "ti,omap4430"
+
+- OMAP3 EVM : Software Developement Board for OMAP35x, AM/DM37x
+ compatible = "ti,omap3-evm", "ti,omap3"
+
+- AM335X EVM : Software Developement Board for AM335x
+ compatible = "ti,am335x-evm", "ti,am33xx", "ti,omap3"
diff --git a/Documentation/devicetree/bindings/arm/sirf.txt b/Documentation/devicetree/bindings/arm/sirf.txt
index 6b07f65b32d..1881e1c6dda 100644
--- a/Documentation/devicetree/bindings/arm/sirf.txt
+++ b/Documentation/devicetree/bindings/arm/sirf.txt
@@ -1,3 +1,3 @@
-prima2 "cb" evalutation board
+prima2 "cb" evaluation board
Required root node properties:
- compatible = "sirf,prima2-cb", "sirf,prima2";
diff --git a/Documentation/devicetree/bindings/arm/spear.txt b/Documentation/devicetree/bindings/arm/spear.txt
new file mode 100644
index 00000000000..f8e54f09232
--- /dev/null
+++ b/Documentation/devicetree/bindings/arm/spear.txt
@@ -0,0 +1,8 @@
+ST SPEAr Platforms Device Tree Bindings
+---------------------------------------
+
+Boards with the ST SPEAr600 SoC shall have the following properties:
+
+Required root node property:
+
+compatible = "st,spear600";
diff --git a/Documentation/devicetree/bindings/arm/tegra/emc.txt b/Documentation/devicetree/bindings/arm/tegra/emc.txt
new file mode 100644
index 00000000000..09335f8eee0
--- /dev/null
+++ b/Documentation/devicetree/bindings/arm/tegra/emc.txt
@@ -0,0 +1,100 @@
+Embedded Memory Controller
+
+Properties:
+- name : Should be emc
+- #address-cells : Should be 1
+- #size-cells : Should be 0
+- compatible : Should contain "nvidia,tegra20-emc".
+- reg : Offset and length of the register set for the device
+- nvidia,use-ram-code : If present, the sub-nodes will be addressed
+ and chosen using the ramcode board selector. If omitted, only one
+ set of tables can be present and said tables will be used
+ irrespective of ram-code configuration.
+
+Child device nodes describe the memory settings for different configurations and clock rates.
+
+Example:
+
+ emc@7000f400 {
+ #address-cells = < 1 >;
+ #size-cells = < 0 >;
+ compatible = "nvidia,tegra20-emc";
+ reg = <0x7000f4000 0x200>;
+ }
+
+
+Embedded Memory Controller ram-code table
+
+If the emc node has the nvidia,use-ram-code property present, then the
+next level of nodes below the emc table are used to specify which settings
+apply for which ram-code settings.
+
+If the emc node lacks the nvidia,use-ram-code property, this level is omitted
+and the tables are stored directly under the emc node (see below).
+
+Properties:
+
+- name : Should be emc-tables
+- nvidia,ram-code : the binary representation of the ram-code board strappings
+ for which this node (and children) are valid.
+
+
+
+Embedded Memory Controller configuration table
+
+This is a table containing the EMC register settings for the various
+operating speeds of the memory controller. They are always located as
+subnodes of the emc controller node.
+
+There are two ways of specifying which tables to use:
+
+* The simplest is if there is just one set of tables in the device tree,
+ and they will always be used (based on which frequency is used).
+ This is the preferred method, especially when firmware can fill in
+ this information based on the specific system information and just
+ pass it on to the kernel.
+
+* The slightly more complex one is when more than one memory configuration
+ might exist on the system. The Tegra20 platform handles this during
+ early boot by selecting one out of possible 4 memory settings based
+ on a 2-pin "ram code" bootstrap setting on the board. The values of
+ these strappings can be read through a register in the SoC, and thus
+ used to select which tables to use.
+
+Properties:
+- name : Should be emc-table
+- compatible : Should contain "nvidia,tegra20-emc-table".
+- reg : either an opaque enumerator to tell different tables apart, or
+ the valid frequency for which the table should be used (in kHz).
+- clock-frequency : the clock frequency for the EMC at which this
+ table should be used (in kHz).
+- nvidia,emc-registers : a 46 word array of EMC registers to be programmed
+ for operation at the 'clock-frequency' setting.
+ The order and contents of the registers are:
+ RC, RFC, RAS, RP, R2W, W2R, R2P, W2P, RD_RCD, WR_RCD, RRD, REXT,
+ WDV, QUSE, QRST, QSAFE, RDV, REFRESH, BURST_REFRESH_NUM, PDEX2WR,
+ PDEX2RD, PCHG2PDEN, ACT2PDEN, AR2PDEN, RW2PDEN, TXSR, TCKE, TFAW,
+ TRPAB, TCLKSTABLE, TCLKSTOP, TREFBW, QUSE_EXTRA, FBIO_CFG6, ODT_WRITE,
+ ODT_READ, FBIO_CFG5, CFG_DIG_DLL, DLL_XFORM_DQS, DLL_XFORM_QUSE,
+ ZCAL_REF_CNT, ZCAL_WAIT_CNT, AUTO_CAL_INTERVAL, CFG_CLKTRIM_0,
+ CFG_CLKTRIM_1, CFG_CLKTRIM_2
+
+ emc-table@166000 {
+ reg = <166000>;
+ compatible = "nvidia,tegra20-emc-table";
+ clock-frequency = < 166000 >;
+ nvidia,emc-registers = < 0 0 0 0 0 0 0 0 0 0 0 0 0 0
+ 0 0 0 0 0 0 0 0 0 0 0 0 0 0
+ 0 0 0 0 0 0 0 0 0 0 0 0 0 0
+ 0 0 0 0 >;
+ };
+
+ emc-table@333000 {
+ reg = <333000>;
+ compatible = "nvidia,tegra20-emc-table";
+ clock-frequency = < 333000 >;
+ nvidia,emc-registers = < 0 0 0 0 0 0 0 0 0 0 0 0 0 0
+ 0 0 0 0 0 0 0 0 0 0 0 0 0 0
+ 0 0 0 0 0 0 0 0 0 0 0 0 0 0
+ 0 0 0 0 >;
+ };
diff --git a/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra20-pmc.txt b/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra20-pmc.txt
new file mode 100644
index 00000000000..b5846e21cc2
--- /dev/null
+++ b/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra20-pmc.txt
@@ -0,0 +1,19 @@
+NVIDIA Tegra Power Management Controller (PMC)
+
+Properties:
+- name : Should be pmc
+- compatible : Should contain "nvidia,tegra<chip>-pmc".
+- reg : Offset and length of the register set for the device
+- nvidia,invert-interrupt : If present, inverts the PMU interrupt signal.
+ The PMU is an external Power Management Unit, whose interrupt output
+ signal is fed into the PMC. This signal is optionally inverted, and then
+ fed into the ARM GIC. The PMC is not involved in the detection or
+ handling of this interrupt signal, merely its inversion.
+
+Example:
+
+pmc@7000f400 {
+ compatible = "nvidia,tegra20-pmc";
+ reg = <0x7000e400 0x400>;
+ nvidia,invert-interrupt;
+};
diff --git a/Documentation/devicetree/bindings/arm/twd.txt b/Documentation/devicetree/bindings/arm/twd.txt
new file mode 100644
index 00000000000..75b8610939f
--- /dev/null
+++ b/Documentation/devicetree/bindings/arm/twd.txt
@@ -0,0 +1,48 @@
+* ARM Timer Watchdog
+
+ARM 11MP, Cortex-A5 and Cortex-A9 are often associated with a per-core
+Timer-Watchdog (aka TWD), which provides both a per-cpu local timer
+and watchdog.
+
+The TWD is usually attached to a GIC to deliver its two per-processor
+interrupts.
+
+** Timer node required properties:
+
+- compatible : Should be one of:
+ "arm,cortex-a9-twd-timer"
+ "arm,cortex-a5-twd-timer"
+ "arm,arm11mp-twd-timer"
+
+- interrupts : One interrupt to each core
+
+- reg : Specify the base address and the size of the TWD timer
+ register window.
+
+Example:
+
+ twd-timer@2c000600 {
+ compatible = "arm,arm11mp-twd-timer"";
+ reg = <0x2c000600 0x20>;
+ interrupts = <1 13 0xf01>;
+ };
+
+** Watchdog node properties:
+
+- compatible : Should be one of:
+ "arm,cortex-a9-twd-wdt"
+ "arm,cortex-a5-twd-wdt"
+ "arm,arm11mp-twd-wdt"
+
+- interrupts : One interrupt to each core
+
+- reg : Specify the base address and the size of the TWD watchdog
+ register window.
+
+Example:
+
+ twd-watchdog@2c000620 {
+ compatible = "arm,arm11mp-twd-wdt";
+ reg = <0x2c000620 0x20>;
+ interrupts = <1 14 0xf01>;
+ };
diff --git a/Documentation/devicetree/bindings/arm/vexpress.txt b/Documentation/devicetree/bindings/arm/vexpress.txt
new file mode 100644
index 00000000000..ec8b50cbb2e
--- /dev/null
+++ b/Documentation/devicetree/bindings/arm/vexpress.txt
@@ -0,0 +1,146 @@
+ARM Versatile Express boards family
+-----------------------------------
+
+ARM's Versatile Express platform consists of a motherboard and one
+or more daughterboards (tiles). The motherboard provides a set of
+peripherals. Processor and RAM "live" on the tiles.
+
+The motherboard and each core tile should be described by a separate
+Device Tree source file, with the tile's description including
+the motherboard file using a /include/ directive. As the motherboard
+can be initialized in one of two different configurations ("memory
+maps"), care must be taken to include the correct one.
+
+Required properties in the root node:
+- compatible value:
+ compatible = "arm,vexpress,<model>", "arm,vexpress";
+ where <model> is the full tile model name (as used in the tile's
+ Technical Reference Manual), eg.:
+ - for Coretile Express A5x2 (V2P-CA5s):
+ compatible = "arm,vexpress,v2p-ca5s", "arm,vexpress";
+ - for Coretile Express A9x4 (V2P-CA9):
+ compatible = "arm,vexpress,v2p-ca9", "arm,vexpress";
+ If a tile comes in several variants or can be used in more then one
+ configuration, the compatible value should be:
+ compatible = "arm,vexpress,<model>,<variant>", \
+ "arm,vexpress,<model>", "arm,vexpress";
+ eg:
+ - Coretile Express A15x2 (V2P-CA15) with Tech Chip 1:
+ compatible = "arm,vexpress,v2p-ca15,tc1", \
+ "arm,vexpress,v2p-ca15", "arm,vexpress";
+ - LogicTile Express 13MG (V2F-2XV6) running Cortex-A7 (3 cores) SMM:
+ compatible = "arm,vexpress,v2f-2xv6,ca7x3", \
+ "arm,vexpress,v2f-2xv6", "arm,vexpress";
+
+Optional properties in the root node:
+- tile model name (use name from the tile's Technical Reference
+ Manual, eg. "V2P-CA5s")
+ model = "<model>";
+- tile's HBI number (unique ARM's board model ID, visible on the
+ PCB's silkscreen) in hexadecimal transcription:
+ arm,hbi = <0xhbi>
+ eg:
+ - for Coretile Express A5x2 (V2P-CA5s) HBI-0191:
+ arm,hbi = <0x191>;
+ - Coretile Express A9x4 (V2P-CA9) HBI-0225:
+ arm,hbi = <0x225>;
+
+Top-level standard "cpus" node is required. It must contain a node
+with device_type = "cpu" property for every available core, eg.:
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu@0 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a5";
+ reg = <0>;
+ };
+ };
+
+The motherboard description file provides a single "motherboard" node
+using 2 address cells corresponding to the Static Memory Bus used
+between the motherboard and the tile. The first cell defines the Chip
+Select (CS) line number, the second cell address offset within the CS.
+All interrupt lines between the motherboard and the tile are active
+high and are described using single cell.
+
+Optional properties of the "motherboard" node:
+- motherboard's memory map variant:
+ arm,v2m-memory-map = "<name>";
+ where name is one of:
+ - "rs1" - for RS1 map (i.a. peripherals on CS3); this map is also
+ referred to as "ARM Cortex-A Series memory map":
+ arm,v2m-memory-map = "rs1";
+ When this property is missing, the motherboard is using the original
+ memory map (also known as the "Legacy memory map", primarily used
+ with the original CoreTile Express A9x4) with peripherals on CS7.
+
+Motherboard .dtsi files provide a set of labelled peripherals that
+can be used to obtain required phandle in the tile's "aliases" node:
+- UARTs, note that the numbers correspond to the physical connectors
+ on the motherboard's back panel:
+ v2m_serial0, v2m_serial1, v2m_serial2 and v2m_serial3
+- I2C controllers:
+ v2m_i2c_dvi and v2m_i2c_pcie
+- SP804 timers:
+ v2m_timer01 and v2m_timer23
+
+Current Linux implementation requires a "arm,v2m_timer" alias
+pointing at one of the motherboard's SP804 timers, if it is to be
+used as the system timer. This alias should be defined in the
+motherboard files.
+
+The tile description must define "ranges", "interrupt-map-mask" and
+"interrupt-map" properties to translate the motherboard's address
+and interrupt space into one used by the tile's processor.
+
+Abbreviated example:
+
+/dts-v1/;
+
+/ {
+ model = "V2P-CA5s";
+ arm,hbi = <0x225>;
+ compatible = "arm,vexpress-v2p-ca5s", "arm,vexpress";
+ interrupt-parent = <&gic>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ chosen { };
+
+ aliases {
+ serial0 = &v2m_serial0;
+ };
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu@0 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a5";
+ reg = <0>;
+ };
+ };
+
+ gic: interrupt-controller@2c001000 {
+ compatible = "arm,cortex-a9-gic";
+ #interrupt-cells = <3>;
+ #address-cells = <0>;
+ interrupt-controller;
+ reg = <0x2c001000 0x1000>,
+ <0x2c000100 0x100>;
+ };
+
+ motherboard {
+ /* CS0 is visible at 0x08000000 */
+ ranges = <0 0 0x08000000 0x04000000>;
+ interrupt-map-mask = <0 0 63>;
+ /* Active high IRQ 0 is connected to GIC's SPI0 */
+ interrupt-map = <0 0 0 &gic 0 0 4>;
+ };
+};
+
+/include/ "vexpress-v2m-rs1.dtsi"