summaryrefslogtreecommitdiffstats
path: root/Documentation/arm/SA1100/GraphicsClient
diff options
context:
space:
mode:
Diffstat (limited to 'Documentation/arm/SA1100/GraphicsClient')
-rw-r--r--Documentation/arm/SA1100/GraphicsClient98
1 files changed, 0 insertions, 98 deletions
diff --git a/Documentation/arm/SA1100/GraphicsClient b/Documentation/arm/SA1100/GraphicsClient
deleted file mode 100644
index 867bb35..0000000
--- a/Documentation/arm/SA1100/GraphicsClient
+++ /dev/null
@@ -1,98 +0,0 @@
-ADS GraphicsClient Plus Single Board Computer
-
-For more details, contact Applied Data Systems or see
-http://www.applieddata.net/products.html
-
-The original Linux support for this product has been provided by
-Nicolas Pitre <nico@fluxnic.net>. Continued development work by
-Woojung Huh <whuh@applieddata.net>
-
-It's currently possible to mount a root filesystem via NFS providing a
-complete Linux environment. Otherwise a ramdisk image may be used. The
-board supports MTD/JFFS, so you could also mount something on there.
-
-Use 'make graphicsclient_config' before any 'make config'. This will set up
-defaults for GraphicsClient Plus support.
-
-The kernel zImage is linked to be loaded and executed at 0xc0200000.
-Also the following registers should have the specified values upon entry:
-
- r0 = 0
- r1 = 29 (this is the GraphicsClient architecture number)
-
-Linux can be used with the ADS BootLoader that ships with the
-newer rev boards. See their documentation on how to load Linux.
-Angel is not available for the GraphicsClient Plus AFAIK.
-
-There is a board known as just the GraphicsClient that ADS used to
-produce but has end of lifed. This code will not work on the older
-board with the ADS bootloader, but should still work with Angel,
-as outlined below. In any case, if you're planning on deploying
-something en masse, you should probably get the newer board.
-
-If using Angel on the older boards, here is a typical angel.opt option file
-if the kernel is loaded through the Angel Debug Monitor:
-
------ begin angelboot.opt -----
-base 0xc0200000
-entry 0xc0200000
-r0 0x00000000
-r1 0x0000001d
-device /dev/ttyS1
-options "38400 8N1"
-baud 115200
-#otherfile ramdisk.gz
-#otherbase 0xc0800000
-exec minicom
------ end angelboot.opt -----
-
-Then the kernel (and ramdisk if otherfile/otherbase lines above are
-uncommented) would be loaded with:
-
- angelboot -f angelboot.opt zImage
-
-Here it is assumed that the board is connected to ttyS1 on your PC
-and that minicom is preconfigured with /dev/ttyS1, 38400 baud, 8N1, no flow
-control by default.
-
-If any other bootloader is used, ensure it accomplish the same, especially
-for r0/r1 register values before jumping into the kernel.
-
-
-Supported peripherals:
-- SA1100 LCD frame buffer (8/16bpp...sort of)
-- on-board SMC 92C96 ethernet NIC
-- SA1100 serial port
-- flash memory access (MTD/JFFS)
-- pcmcia
-- touchscreen(ucb1200)
-- ps/2 keyboard
-- console on LCD screen
-- serial ports (ttyS[0-2])
- - ttyS0 is default for serial console
-- Smart I/O (ADC, keypad, digital inputs, etc)
- See http://www.eurotech-inc.com/linux-sbc.asp for IOCTL documentation
- and example user space code. ps/2 keybd is multiplexed through this driver
-
-To do:
-- UCB1200 audio with new ucb_generic layer
-- everything else! :-)
-
-Notes:
-
-- The flash on board is divided into 3 partitions. mtd0 is where
- the ADS boot ROM and zImage is stored. It's been marked as
- read-only to keep you from blasting over the bootloader. :) mtd1 is
- for the ramdisk.gz image. mtd2 is user flash space and can be
- utilized for either JFFS or if you're feeling crazy, running ext2
- on top of it. If you're not using the ADS bootloader, you're
- welcome to blast over the mtd1 partition also.
-
-- 16bpp mode requires a different cable than what ships with the board.
- Contact ADS or look through the manual to wire your own. Currently,
- if you compile with 16bit mode support and switch into a lower bpp
- mode, the timing is off so the image is corrupted. This will be
- fixed soon.
-
-Any contribution can be sent to nico@fluxnic.net and will be greatly welcome!
-